Garmin GT41-TH - Stainless Steel Thru-Hull DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducer with Temp 12-pin Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin GT41-TH - Stainless Steel Thru-Hull DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducer with Temp 12-pin manuals!
Problems with Garmin GT41-TH - Stainless Steel Thru-Hull DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducer with Temp 12-pin?
Ask a Question
Free Garmin GT41-TH - Stainless Steel Thru-Hull DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducer with Temp 12-pin manuals!
Problems with Garmin GT41-TH - Stainless Steel Thru-Hull DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducer with Temp 12-pin?
Ask a Question
Popular Garmin GT41-TH - Stainless Steel Thru-Hull DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducer with Temp 12-pin Manual Pages
Installation Instructions - Page 1
..., and relays sound-wave information to install and maintain this equipment in a safe
place.
Thru-Hull Transducer
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in Taiwan
190-01774-02_0B
Read all installation instructions before the device restarts fully, the software update is complete. 5 Remove the memory card...
Installation Instructions - Page 2
... Hull Installation Instructions
Thru-Hull Transducer in a Cored Hull with at least one of the included anti-rotation bolts. Drilling the Transducer Stem Hole and the Anti-Rotation Bolt Holes in a Cored Fiberglass Hull ...the propeller.
The transducer must be in clean (non-turbulent) water for the deadrise angle of the specific point on the table so the cutting guide rests against the fence...
Installation Instructions - Page 3
... should follow these instructions, with one inside the hull, slide the backing block onto the transducer stem and seat it firmly against the inner hull. Do not apply sealant directly to the stem or anti-rotation bolts.
Drilling the Transducer Stem and Anti-Rotation Bolt Holes Using a Template
WARNING The device must be installed with at...
Installation Instructions - Page 4
... cut the fairing block (Cutting the Fairing Block).
Non-cored/Fiberglass Boat Hull Installation Instructions
Thru-Hull Transducer in a Non-cored/Fiberglass Hull with a Fairing Block If the deadrise angle of the stem hole and
anti-rotation bolts. 3 Drill a 3 mm (1/8 in.) pilot hole and hull at the stem hole
location, from outside of the stem and À...
Installation Instructions - Page 5
... a Template
WARNING The device must be installed with the
included M8 nuts and 8 mm washers .
Ç
È
Do not over-tighten the M8 nuts.
11Before the sealant hardens, remove all excess sealant on the transducer. You should follow these instructions, with an 9 mm (3/8 in a non-cored fiberglass hull, avoid over-tightening the nuts to prevent...
Installation Instructions - Page 6
... and seat it firmly against the hull.
3 From inside the hull, apply the included anti-seize compound to the exposed transducer stem and anti-rotation bolts.
4 From inside the boat.
1 Secure the bushings to the anti-rotation bolts and
À
Á
transducer stem .
Â
Metal Boat Hull Installation Instructions
Thru-Hull Transducer in a Metal Hull with a Fairing Block
It is...
Installation Instructions - Page 7
NOTE: When installing a transducer in an aluminum or steel hull, you must use the included isolation plate.
1 Secure the bushings to the anti-rotation bolts .
À
Á
2 Seat the isolation plate firmly against the transducer.
Â
Drilling the Transducer Stem and Anti-Rotation Bolt Holes Using a Template
WARNING The device must be installed with a 12 mm (1/2 in a Metal Hull without...
Installation Instructions - Page 8
... destroy your transducer. Item
À Á Â Ã
Description Chartplotter Sounder Power Source Y-cable
Maintenance
Testing the Installation
NOTICE You should apply a water-based anti-fouling paint to the hull of your vessel every six months.
Anti-Fouling Paint To prevent corrosion on metal hulls and to work properly. Garmin® and the Garmin logo are...
Garmin GT41-TH - Stainless Steel Thru-Hull DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducer with Temp 12-pin Reviews
We have not received any reviews for Garmin yet.