Garmin GT50M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 455/800 kHz Traditional 300 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-pin Support and Manuals

Get Help and Manuals for this Garmin item

+ Add to My products ?

This item is in your list!

View All Support Options Below
Free Garmin GT50M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 455/800 kHz Traditional 300 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-pin manuals!
Problems with Garmin GT50M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 455/800 kHz Traditional 300 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-pin?

Ask a Question

Popular Garmin GT50M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 455/800 kHz Traditional 300 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-pin Manual Pages

Installation Instructions - Page 1

... that enhances your awareness of your boat, you by a qualified marine installer. Thru-Hull Transducer Installation Instructions Important Safety Information WARNING See the Important Safety and Product Information guide in the product box for in-country support information. • In the USA, call 913-397-8200 or 1-800-800-1020. • In the UK, call 0808 238 0000. •...

Installation Instructions - Page 2

... to install the transducer. Drilling the Transducer Stem Hole and the Anti-Rotation Bolt Holes in a Cored Fiberglass Hull Before you can also ask your boat manufacturer for the deadrise angle of the specific point on your mounting location exceeds 5°, you must drill the hole for increased sonar accuracy. The wood becomes a cutting guide for...

Installation Instructions - Page 3

... to ensure a tight, waterproof seal between the fairing block and the hull. NOTE: When installing the transducer in a Cored Hull without a Fairing Block If the deadrise angle of the anti-rotation bolts and transducer stem . Á 7 From inside the boat. You should follow these instructions, with one positioned outside the boat and one of the fairing...

Installation Instructions - Page 4

... inside the boat. You should use a utility knife to cut the fairing block (Cutting the Fairing Block). Non-cored/Fiberglass Boat Hull Installation Instructions Thru-Hull Transducer in a non-cored fiberglass hull, avoid over the transducer. Do not over the pilot hole, use a fairing block to Æ the anti-rotation bolts. Do not apply sealant directly to...

Installation Instructions - Page 5

... washer . Æ Do not over -tightening the nuts to prevent damaging the hull. 1 Apply marine sealant to the base of the anti-rotation bolts and transducer stem , and to the sides of the transducer plate Á that two installers complete these instructions if you can mount the device without surface irregularities or obstructions. 3 Using the...

Installation Instructions - Page 6

... bushings to the anti-rotation bolts and À Á transducer stem .  Metal Boat Hull Installation Instructions Thru-Hull Transducer in .) hole saw, cut the stem hole from outside the hull, insert the transducer through the ull at the base of the anti-rotation bolts and transducer stem. 3 Seat the transducer housing firmly within the fairing block à recess...

Installation Instructions - Page 7

...12 mm (1/2 in a Metal Hull without a Fairing Block If the deadrise angle of your mounting location does not exceed 5°, you must complete all other installation instructions. Thru-Hull Transducer...cut the stem hole from outside the hull. Installing the Transducer in an aluminum or steel hull, you are not using a fairing block to mount your transducers to the network, power, and ...

Installation Instructions - Page 8

... to work properly. or its subsidiaries www.garmin.com/support Because water is severe, use a scouring pad or putty knife to remove growth. 3 Wipe the device dry. Garmin® and the Garmin logo are trademarks of the water. Anti-Fouling Paint To prevent corrosion on metal hulls and to slow the growth of organisms that...

Garmin GT50M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 455/800 kHz Traditional 300 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-pin Reviews

Popular Garmin GT50M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 455/800 kHz Traditional 300 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-pin Search Terms