Garmin GT51M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-Pin Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin GT51M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-Pin manuals!
Problems with Garmin GT51M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-Pin?
Ask a Question
Free Garmin GT51M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-Pin manuals!
Problems with Garmin GT51M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-Pin?
Ask a Question
Popular Garmin GT51M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-Pin Manual Pages
Installation Instructions - Page 1
...installed with the installation. You are responsible for the software update instructions to appear, the device must install the Garmin® transducer according to these instructions could cause damage to install...-Hull Transducer
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in the product box for in-country support
...
Installation Instructions - Page 2
... on the table so the cutting guide rests against water seepage. 1 Select...12 in .).
2
The hole must be installed with at the mounting
location. 3 Tilt your vessel.
• The transducer should not be mounted behind strakes, struts, fittings, water intake or discharge ports, or anything that can also ask your boat manufacturer for the deadrise angle of the specific point on your boat hull...
Installation Instructions - Page 3
...-rotation bolts. NOTE: When installing the transducer in a cored fiberglass hull, avoid over the transducer. The hole must be perpendicular to the water surface. 6 Sand and clean the inner skin, core, and outer skin around
the hole. 7 Seal the exposed inner core with epoxy , and allow the
à epoxy to set thoroughly. 8 While holding a drill...
Installation Instructions - Page 4
... over-tighten the M8 nuts.
6 Before the sealant hardens, remove all excess sealant on the transducer. You should use a utility knife to Æ the anti-rotation bolts.
Non-cored/Fiberglass Boat Hull Installation Instructions
Thru-Hull Transducer in .) pilot hole and hull at the stem hole
location, from outside of the stem hole and
anti-rotation bolts...
Installation Instructions - Page 5
... bolt holes from outside the hull.
You should follow these instructions, with at the base of the anti-rotation bolts and transducer stem . Á
3 Seat the transducer housing firmly within the fairing block Â
recess.
4 Apply marine sealant to the face of the fairing block that two installers complete these instructions if you can mount...
Installation Instructions - Page 6
... boat and one inside the boat.
1 Secure the bushings to the anti-rotation bolts and
À
Á
transducer stem .
Â
Metal Boat Hull Installation Instructions
Thru-Hull Transducer in a Metal Hull with a 13 mm (1/2 in a Metal Hull You should follow these instructions when you should use slip-joint pliers or a crescent wrench to secure the included M8 nuts and...
Installation Instructions - Page 7
... isolation plate that two installers complete these instructions if you must complete all excess sealant on the
outside of the included anti-rotation bolts.
You can mount the device without a Fairing Block It is moving and could result in an aluminum or steel hull, you are not using the Y-cable.
7 Thru-Hull Transducer in .) bit plumb...
Installation Instructions - Page 8
...Maintenance
Testing the Installation
NOTICE You should apply a water-based anti-fouling paint to the hull of the ...transducer. Anti-Fouling Paint To prevent corrosion on metal hulls and to carry the sonar signal, the transducer must be used without the express permission of Garmin Ltd. Cleaning the Transducer...garmin.com/support These trademarks may not be in the USA and other countries...
Garmin GT51M-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W Mid-band CHIRP 80-160 kHz Transducers with Temp 12-Pin Reviews
We have not received any reviews for Garmin yet.