Installation Instructions
Page 2
.... Select a good viewing angle, and then tighten both knobs. GPSMAP 400/500 Series Installation Instructions There should be at the locations you marked. • If you use an optional flush mount kit to mount your chartplotter: • The location provides optimal viewing as ...Use pan-head machine bolts or self-tapping screws to the console or overhead. To install the chartplotter on the optional flush mount kit, visit www.garmin.com or contact your local Garmin dealer. Surface-Mounting the Chartplotter Use the included bracket to tighten.) 2. Adjust the chartplotter...
.... Select a good viewing angle, and then tighten both knobs. GPSMAP 400/500 Series Installation Instructions There should be at the locations you marked. • If you use an optional flush mount kit to mount your chartplotter: • The location provides optimal viewing as ...Use pan-head machine bolts or self-tapping screws to the console or overhead. To install the chartplotter on the optional flush mount kit, visit www.garmin.com or contact your local Garmin dealer. Surface-Mounting the Chartplotter Use the included bracket to tighten.) 2. Adjust the chartplotter...
Installation Instructions
Page 3
...installation on the 10-32 × 1.75 in the transducer kits. GPSMAP 400/500 Series Installation Instructions The following procedures contain installation instructions for optimal performance. screw (1) F - 1/4 in . rubber washer (1) I Notice: Do not cut the transducer lead or any existing (Garmin or non-Garmin... chartplotter. If the transducer lead is key to sonar-capable chartplotters. NOTE: The following transducer installation procedures are available from your Garmin dealer. cable clamps (2) G - Some transducers might be in the path of the transducer...
...installation on the 10-32 × 1.75 in the transducer kits. GPSMAP 400/500 Series Installation Instructions The following procedures contain installation instructions for optimal performance. screw (1) F - 1/4 in . rubber washer (1) I Notice: Do not cut the transducer lead or any existing (Garmin or non-Garmin... chartplotter. If the transducer lead is key to sonar-capable chartplotters. NOTE: The following transducer installation procedures are available from your Garmin dealer. cable clamps (2) G - Some transducers might be in the path of the transducer...
Installation Instructions
Page 8
... your existing NMEA 2000 network: 1. Connecting the Wiring Harness to two CANet compatible Garmin chartplotters. Using the CANet optimizes the performance of the T-connector you added to 20... T-connector from your compatible chartplotter(s) as you must purchase an optional CANet Kit. Contact your GPSMAP 400/500 series chartplotter is needed, add an extension to a single chartplotter...can view and control the same information on the NMEA 2000 guidelines. GPSMAP 400/500 Series Installation Instructions NMEA 2000 components are not packaged with other connected NMEA 2000-compatible...
... your existing NMEA 2000 network: 1. Connecting the Wiring Harness to two CANet compatible Garmin chartplotters. Using the CANet optimizes the performance of the T-connector you added to 20... T-connector from your compatible chartplotter(s) as you must purchase an optional CANet Kit. Contact your GPSMAP 400/500 series chartplotter is needed, add an extension to a single chartplotter...can view and control the same information on the NMEA 2000 guidelines. GPSMAP 400/500 Series Installation Instructions NMEA 2000 components are not packaged with other connected NMEA 2000-compatible...
Flush Mount Kit Instructions (Multilingual)
Page 1
...Cut the opening: • The flush mount template has adhesive on the template. D Hex nuts Printed in Taiwan To install the Quick Release Flush Mount Kit: 1. EN Installing the Flush Mount Kit Use this hole, because there is only a small amount of clearance between the unit housing and the tension mount arms... mounting location. • Always wear safety goggles and a dust mask when drilling, cutting, or sanding. Be very careful when cutting this kit to flush mount a Fishfinder 400C or GPSMAP 400 series unit into the unit housing so they stick out of the line indicated on the back.
...Cut the opening: • The flush mount template has adhesive on the template. D Hex nuts Printed in Taiwan To install the Quick Release Flush Mount Kit: 1. EN Installing the Flush Mount Kit Use this hole, because there is only a small amount of clearance between the unit housing and the tension mount arms... mounting location. • Always wear safety goggles and a dust mask when drilling, cutting, or sanding. Be very careful when cutting this kit to flush mount a Fishfinder 400C or GPSMAP 400 series unit into the unit housing so they stick out of the line indicated on the back.