Flush Mount Template
Page 1
FLUSH MOUNT TEMPLATE GPSMAP 172C/178C (EXTERNAL ANTENNA VERSIONS ONLY) UNIT OUTLINE CUT MOUNTING SURFACE ALONG THE ... .050" Allen Wrench to overtighten as this hole, there is snug against the mounting surface. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, U.S.A. Place washers over the Mounting Studs, then thread...four Mounting Studs to swing open freely. 100.0 mm (3.93") 138.0 mm (5.43") © Copyright 2004 Garmin Ltd. Install and tighten the second Hex Nut on one in to the back of clearance between the unit and...
FLUSH MOUNT TEMPLATE GPSMAP 172C/178C (EXTERNAL ANTENNA VERSIONS ONLY) UNIT OUTLINE CUT MOUNTING SURFACE ALONG THE ... .050" Allen Wrench to overtighten as this hole, there is snug against the mounting surface. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, U.S.A. Place washers over the Mounting Studs, then thread...four Mounting Studs to swing open freely. 100.0 mm (3.93") 138.0 mm (5.43") © Copyright 2004 Garmin Ltd. Install and tighten the second Hex Nut on one in to the back of clearance between the unit and...
Owner's Manual
Page 8
...• BlueChart Marine Data Cards, MapSource CDs, USB Data Card Programmer, and Data Cards • GSD 20 Remote Sounder Module • GBR 23 Beacon Receiver for differential corrections Standard Package: • GPSMAP 172/172C Unit • GA 29 Remote External Antenna and 30' cable* • Internal Antenna** • ... Not included with part numbers 010-00327-01 with internal antenna. ** Not included with part numbers 010-00327-00 with your unit, please check to see that your package includes the following items. If any parts are missing, please contact your Garmin dealer immediately.
...• BlueChart Marine Data Cards, MapSource CDs, USB Data Card Programmer, and Data Cards • GSD 20 Remote Sounder Module • GBR 23 Beacon Receiver for differential corrections Standard Package: • GPSMAP 172/172C Unit • GA 29 Remote External Antenna and 30' cable* • Internal Antenna** • ... Not included with part numbers 010-00327-01 with internal antenna. ** Not included with part numbers 010-00327-00 with your unit, please check to see that your package includes the following items. If any parts are missing, please contact your Garmin dealer immediately.
Owner's Manual
Page 99
... exceeding this range (in all directions to support the unit and protect it from excessive vibration and shock. • For GPSMAP 172/172C unit's with self-tapping screws, drill starter holes at the locations you risk damaging the Mounting Base. 89 Drill, Screwdriver ... (7 cm) clearance behind the case to allow connection of the antenna (external antenna only), power/data cables. • The mounting surface should be heavy enough to ensure the best reception. Mounting the GPSMAP 172/172C Unit The GPSMAP 172/172C's compact, waterproof case is suitable for drilling starter holes. I ...
... exceeding this range (in all directions to support the unit and protect it from excessive vibration and shock. • For GPSMAP 172/172C unit's with self-tapping screws, drill starter holes at the locations you risk damaging the Mounting Base. 89 Drill, Screwdriver ... (7 cm) clearance behind the case to allow connection of the antenna (external antenna only), power/data cables. • The mounting surface should be heavy enough to ensure the best reception. Mounting the GPSMAP 172/172C Unit The GPSMAP 172/172C's compact, waterproof case is suitable for drilling starter holes. I ...
Owner's Manual
Page 101
To flush mount the GPSMAP 172/172C (External Antenna ONLY): Included Mounting Hardware - 4 - 3mm Studs, 4 - Center Punch, Drill, 1/8" (3mm) Drill Bit, 3/8" (6mm) Drill Bit, Jig Saw, 1/16" (2mm) Allen Wrench, 9/35" (7mm) Wrench. 1. Using...place. It may damage the Mounting Stud. Place washers over the Mounting Studs, then thread on a flat panel. Flush Mounting the GPSMAP 172/172C External Antenna Unit The GPSMAP 172/172C External Antenna only can be prudent to cut the mounting surface along the inside the cutout area of the mounting surface. 8. Check that all cables...
To flush mount the GPSMAP 172/172C (External Antenna ONLY): Included Mounting Hardware - 4 - 3mm Studs, 4 - Center Punch, Drill, 1/8" (3mm) Drill Bit, 3/8" (6mm) Drill Bit, Jig Saw, 1/16" (2mm) Allen Wrench, 9/35" (7mm) Wrench. 1. Using...place. It may damage the Mounting Stud. Place washers over the Mounting Studs, then thread on a flat panel. Flush Mounting the GPSMAP 172/172C External Antenna Unit The GPSMAP 172/172C External Antenna only can be prudent to cut the mounting surface along the inside the cutout area of the mounting surface. 8. Check that all cables...