Manual/User Guide
Page 1
C141-E262 3-1 CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
C141-E262 3-1 CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
Manual/User Guide
Page 2
All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive. Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E262
All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive. Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E262
Manual/User Guide
Page 3
... attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other than parts to which the HDD is connected to Signal Ground (SG). Use M3 screw for the mounting screw and the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE...
... attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other than parts to which the HDD is connected to Signal Ground (SG). Use M3 screw for the mounting screw and the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE...
Manual/User Guide
Page 4
Installation Conditions (3) Limitation of A 3.0 or less Screw Figure 3.2 Mounting frame structure 3-4 C141-E262 Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less Screw Details of mounting Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us.
Installation Conditions (3) Limitation of A 3.0 or less Screw Figure 3.2 Mounting frame structure 3-4 C141-E262 Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less Screw Details of mounting Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us.
Manual/User Guide
Page 5
Locating of breather C141-E262 3-5 Figure 3.3 Location of breather hole is shown as Figure 3.3. For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. 3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to block.
Locating of breather C141-E262 3-5 Figure 3.3 Location of breather hole is shown as Figure 3.3. For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. 3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to block.
Manual/User Guide
Page 6
...;C max 3-6 C141-E262 To check the cooling efficiency, measure the surface cover temperatures of the ambient temperature, this surface cover temperature must be considered to the ambient temperature at a point 3 cm from exceeding 60 °C. Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover temperature from the disk drive. The ambient temperature must...
...;C max 3-6 C141-E262 To check the cooling efficiency, measure the surface cover temperatures of the ambient temperature, this surface cover temperature must be considered to the ambient temperature at a point 3 cm from exceeding 60 °C. Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover temperature from the disk drive. The ambient temperature must...
Manual/User Guide
Page 7
..., and handle the HDD under the safety environment. Mounting screw hole Cable connection Mounting screw hole Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Damage: Do not press the cover of the disk drive. 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. Static: When handling...
..., and handle the HDD under the safety environment. Mounting screw hole Cable connection Mounting screw hole Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Damage: Do not press the cover of the disk drive. 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. Static: When handling...
Manual/User Guide
Page 8
... not drop. Installation (1) Please use an electric driver. General notes Wrist strap Use the Wrist strap. Do not hit HDD each other. ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it. Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056...
... not drop. Installation (1) Please use an electric driver. General notes Wrist strap Use the Wrist strap. Do not hit HDD each other. ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it. Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056...
Manual/User Guide
Page 9
SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E262 3-9 Figure 3.7 shows the locations of these connectors and terminals. 3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices.
SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E262 3-9 Figure 3.7 shows the locations of these connectors and terminals. 3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices.
Manual/User Guide
Page 10
... the disk drive must be compliant with Serial-ATA Revision 2.5 specification. Therefore, we recommend that the customer evaluate the connector on the customer's system and select it from the PCA side Figure 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for host system The connector of the connection with the Serial ATA Revision 2.5 specification. 3-10 C141-E262 Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of requirements about SATA interface connector...
... the disk drive must be compliant with Serial-ATA Revision 2.5 specification. Therefore, we recommend that the customer evaluate the connector on the customer's system and select it from the PCA side Figure 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for host system The connector of the connection with the Serial ATA Revision 2.5 specification. 3-10 C141-E262 Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of requirements about SATA interface connector...
Manual/User Guide
Page 11
... cable without releasing the SATA interface Latch may lead to remove the cable while releasing the Latch. C141-E262 3-11 Accordingly, be compliant with the Serial ATA Revision 2.5 specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connector and the host receptacle or SATA interface cable connector...
... cable without releasing the SATA interface Latch may lead to remove the cable while releasing the Latch. C141-E262 3-11 Accordingly, be compliant with the Serial ATA Revision 2.5 specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connector and the host receptacle or SATA interface cable connector...