Manual/User Guide
Page 3
... the system frame, do not allow the system frame to touch parts (cover and base) other than parts to which the HDD is connected to Signal Ground (SG). Use M3 screw for the mounting screw and the screw length should satisfy the specification in ... The MR head bias of the HDD disk enclosure (DE) is zero. The tightening torque must be mounted in Figure 3.2. C141-E262 3-3 The mounting frame is attached. 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf...
... the system frame, do not allow the system frame to touch parts (cover and base) other than parts to which the HDD is connected to Signal Ground (SG). Use M3 screw for the mounting screw and the screw length should satisfy the specification in ... The MR head bias of the HDD disk enclosure (DE) is zero. The tightening torque must be mounted in Figure 3.2. C141-E262 3-3 The mounting frame is attached. 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf...
Manual/User Guide
Page 5
Figure 3.3 Location of breather hole is shown as Figure 3.3. Locating of breather C141-E262 3-5 For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. 3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to block.
Figure 3.3 Location of breather hole is shown as Figure 3.3. Locating of breather C141-E262 3-5 For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. 3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to block.
Manual/User Guide
Page 7
...: Do not press the cover of the disk drive. C141-E262 3-7 Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Ensure that the disk drive is not affected by the edges. (6) Handling cautions... Please keep the following cautions, and handle the HDD under the safety environment. Pressing it ...
...: Do not press the cover of the disk drive. C141-E262 3-7 Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Ensure that the disk drive is not affected by the edges. (6) Handling cautions... Please keep the following cautions, and handle the HDD under the safety environment. Pressing it ...
Manual/User Guide
Page 8
Do not hit HDD each other. Do not drop. Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY-8A (Color Seiden ... shock absorbing mat on the operation table, and place ESD mat on it. Figure 3.6 Handling cautions - Do not place HDD vertically to avoid falling down. Installation Conditions - Do not stack when carrying. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you...
Do not hit HDD each other. Do not drop. Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY-8A (Color Seiden ... shock absorbing mat on the operation table, and place ESD mat on it. Figure 3.6 Handling cautions - Do not place HDD vertically to avoid falling down. Installation Conditions - Do not stack when carrying. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you...