Manual/User Guide
Page 1
C141-E262 3-1 CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
C141-E262 3-1 CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
Manual/User Guide
Page 2
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E262 All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive.
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E262 All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive.
Manual/User Guide
Page 3
... The MR head bias of the HDD disk enclosure (DE) is attached. When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other than parts to Signal Ground (SG). C141-E262 3-3 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be...
... The MR head bias of the HDD disk enclosure (DE) is attached. When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other than parts to Signal Ground (SG). C141-E262 3-3 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be...
Manual/User Guide
Page 4
Installation Conditions (3) Limitation of A 3.0 or less Screw Figure 3.2 Mounting frame structure 3-4 C141-E262 Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less Screw Details of mounting Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us.
Installation Conditions (3) Limitation of A 3.0 or less Screw Figure 3.2 Mounting frame structure 3-4 C141-E262 Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less Screw Details of mounting Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us.
Manual/User Guide
Page 5
For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. Locating of breather C141-E262 3-5 Figure 3.3 Location of breather hole is shown as Figure 3.3. 3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to block.
For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. Locating of breather C141-E262 3-5 Figure 3.3 Location of breather hole is shown as Figure 3.3. 3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to block.
Manual/User Guide
Page 6
Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover temperature from the disk drive. Regardless of the DE. Figure 3.4 shows the temperature measurement point. 1 Figure 3.4 Surface cover temperature measurement points Table 3.1 Surface temperature measurement points and standard values No. To check the cooling efficiency, measure the surface cover temperatures of the ambient...
Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover temperature from the disk drive. Regardless of the DE. Figure 3.4 shows the temperature measurement point. 1 Figure 3.4 Surface cover temperature measurement points Table 3.1 Surface temperature measurement points and standard values No. To check the cooling efficiency, measure the surface cover temperatures of the ambient...
Manual/User Guide
Page 7
... 3.5 shows how the drive must be accessed (service areas) during and after installation. Ensure that the disk drive is not affected by the edges. (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. Pressing it by external magnetic fields. Do not touch the printed circuit board, but hold it too hard, the cover and...
... 3.5 shows how the drive must be accessed (service areas) during and after installation. Ensure that the disk drive is not affected by the edges. (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. Pressing it by external magnetic fields. Do not touch the printed circuit board, but hold it too hard, the cover and...
Manual/User Guide
Page 8
... avoid falling down. Do not hit HDD each other. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use an electric driver. Installation (1) Please use the driver of the screw strictly. Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY-8A...
... avoid falling down. Do not hit HDD each other. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use an electric driver. Installation (1) Please use the driver of the screw strictly. Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY-8A...
Manual/User Guide
Page 9
3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals. SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E262 3-9
3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals. SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E262 3-9
Manual/User Guide
Page 10
... 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for mating with the disk drive must be compliant with the Serial ATA Revision 2.5 specification. 3-10 C141-E262 The connection reliability per number of insertion/extractions varies with the condition of requirements about SATA interface connector, refer to the "Serial-ATA Revision 2.5." Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of host system for host system The connector of the SATA interface connector and pin numbers.
... 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for mating with the disk drive must be compliant with the Serial ATA Revision 2.5 specification. 3-10 C141-E262 The connection reliability per number of insertion/extractions varies with the condition of requirements about SATA interface connector, refer to the "Serial-ATA Revision 2.5." Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of host system for host system The connector of the SATA interface connector and pin numbers.
Manual/User Guide
Page 11
... SATA interface Latch may lead to remove the cable while releasing the Latch. C141-E262 3-11 Accordingly, be compliant with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be sure to connector damage and the loss of force in the connection direction once they are snugly and securely in position. 3.3 Connections with the Serial ATA Revision 2.5 specification. 3.3.5 Note about SATA interface cable connection...
... SATA interface Latch may lead to remove the cable while releasing the Latch. C141-E262 3-11 Accordingly, be compliant with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be sure to connector damage and the loss of force in the connection direction once they are snugly and securely in position. 3.3 Connections with the Serial ATA Revision 2.5 specification. 3.3.5 Note about SATA interface cable connection...