Fujitsu MHY2160BH - 160GB SATA/150 5400RPM 8MB 2.5" Hard Drive Support and Manuals
Get Help and Manuals for this Fujitsu item
View All Support Options Below
Free Fujitsu MHY2160BH manuals!
Problems with Fujitsu MHY2160BH?
Ask a Question
Free Fujitsu MHY2160BH manuals!
Problems with Fujitsu MHY2160BH?
Ask a Question
Popular Fujitsu MHY2160BH Manual Pages
Manual/User Guide - Page 1
C141-E262
3-1
CHAPTER 3 Installation Conditions
3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System
This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
Manual/User Guide - Page 2
Installation Conditions
3.1 Dimensions
Figure 3.1 illustrates the dimensions of the
connector pins
Figure 3.1 Dimensions
3-2
C141-E262 All dimensions are in mm.
*1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of...
Manual/User Guide - Page 3
... should satisfy the specification in any direction.
(2) Frame
The MR head bias of the HDD disk enclosure (DE) is zero.
The mounting frame is attached.
The tightening torque must be mounted in Figure 3.2. 3.2 Mounting
3.2 Mounting
For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)."
(1) Orientation The disk drives can be 0.49N...
Manual/User Guide - Page 4
Bottom surface mounting
DE
2 A
Frame of system cabinet
2.5 2.5
2.5
Side surface
2.5
mounting
PCA
B
Frame of system
cabinet
3.0 or less
Screw
Details of mounting
Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us. Installation Conditions
(3) Limitation of A
3.0 or less
Screw
Figure 3.2 Mounting frame structure
3-4
C141-E262
Manual/User Guide - Page 5
Figure 3.3 Location of breather hole is shown as Figure 3.3. Locating of breather
C141-E262
3-5 For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. 3.2 Mounting
Because of breather hole mounted to the HDD, do not allow this to block.
Manual/User Guide - Page 6
... cover temperature measurement points
Table 3.1 Surface temperature measurement points and standard values
No. Installation Conditions
(4) Ambient temperature
The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover temperature from the disk drive. To check the cooling efficiency, measure the surface cover temperatures of the ambient temperature...
Manual/User Guide - Page 7
...Please keep the following cautions, and handle the HDD under the safety environment.
Mounting screw hole
Cable connection
Mounting screw hole Figure 3.5 Service area
Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. 3.2 Mounting
(5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation.
Manual/User Guide - Page 8
...HDD is occasionally damaged by the impact of the driver.
(2) Please observe the tightening torque of a low impact when you use the driver of the screw strictly. Recommended equipments
ESD Shock
Contents Wrist strap ESD mat
Low shock driver
Model... JX-1200-3056-8 SKY-8A (Color Seiden Mat)
SS-6500
Maker SUMITOMO 3M
Achilles HIOS
3-8
C141-E262 Installation Conditions -...
Manual/User Guide - Page 9
SATA interface and power connectors
PCA
Figure 3.7 Connector locations
C141-E262
3-9 Figure 3.7 shows the locations of these connectors and terminals. 3.3 Connections with Host System
3.3 Connections with Host System
3.3.1 Device connector
The disk drive has the SATA interface connectors listed below for connecting external devices.
Manual/User Guide - Page 10
...specifications for host system The connector of requirements about SATA interface connector, refer to the "Serial-ATA Revision 2.5."
Installation Conditions
3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of the connection with the host system. For detail of host system for mating with the disk drive must be compliant with Serial-ATA Revision 2.5 specification...
Manual/User Guide - Page 11
...in position. 3.3 Connections with the Serial ATA Revision 2.5 specification.
3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle:
When plugging together the disk drive SATA interface connector and the host receptacle or SATA...
Fujitsu MHY2160BH Reviews
We have not received any reviews for Fujitsu yet.