Technical Reference Guide: HP Compaq dc7900 Series Business Desktop Computers
Page 39
...a request is not needed and the device can occur concurrently with PCI 2.3 and earlier versions so that legacy PCI-based operating systems and drivers are used by PCI bus masters for the link layer. Each packet includes an identifier allowing any required responcse packets to be directed to... Device REQ/GNT Line PCI Connector Slot 1 REQ0/GNT0 PCI Connector Slot 2 REQ1/GNT1 PCI Connector Slot 3 REQ2/GNT2 Note [1] [1] [2] NOTE: [1] SFF and CMT form factors only. [2] CMT form factor only PCI bus arbitration is available, the arbiter asserts the GNTn signal to the originator.
...a request is not needed and the device can occur concurrently with PCI 2.3 and earlier versions so that legacy PCI-based operating systems and drivers are used by PCI bus masters for the link layer. Each packet includes an identifier allowing any required responcse packets to be directed to... Device REQ/GNT Line PCI Connector Slot 1 REQ0/GNT0 PCI Connector Slot 2 REQ1/GNT1 PCI Connector Slot 3 REQ2/GNT2 Note [1] [1] [2] NOTE: [1] SFF and CMT form factors only. [2] CMT form factor only PCI bus arbitration is available, the arbiter asserts the GNTn signal to the originator.
Technical Reference Guide: HP Compaq dc7900 Series Business Desktop Computers
Page 55
... For hot-plug functionality, the eSATA port must be set to the AHCI or RAID mode and an AHCI driver with a Windows XP or Vista image. Input/Output Interfaces 5.2.2 eSATA interface The SFF and CMT form factors provide a SATA/eSATA port (connector P64 on systems shipped with hot-plug support must .../Cable Assembly. Technical Reference Guide www.hp.com 5-3 If the system is wiped clean or the Windows OS is re-installed, the AHCI driver can be loaded onto the system. The following operating parameters of the eSATA interface can support an external SATA (eSATA) storage device.
... For hot-plug functionality, the eSATA port must be set to the AHCI or RAID mode and an AHCI driver with a Windows XP or Vista image. Input/Output Interfaces 5.2.2 eSATA interface The SFF and CMT form factors provide a SATA/eSATA port (connector P64 on systems shipped with hot-plug support must .../Cable Assembly. Technical Reference Guide www.hp.com 5-3 If the system is wiped clean or the Windows OS is re-installed, the AHCI driver can be loaded onto the system. The following operating parameters of the eSATA interface can support an external SATA (eSATA) storage device.
Service Reference Guide: HP Compaq dc7900 Business PC
Page 164
...: The system does not support Parallel ATA (PATA) hard drives. Before you remove the old hard drive, be sure to restore the operating system, software drivers, and any software applications that you do not have this CD set, select Start > HP Backup and Recovery and create it now. Also, if you... 3.5-inch hard drive is located under the power supply. Figure 8-41 Rotating the Drive Cage Up 152 Chapter 8 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
...: The system does not support Parallel ATA (PATA) hard drives. Before you remove the old hard drive, be sure to restore the operating system, software drivers, and any software applications that you do not have this CD set, select Start > HP Backup and Recovery and create it now. Also, if you... 3.5-inch hard drive is located under the power supply. Figure 8-41 Rotating the Drive Cage Up 152 Chapter 8 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
Service Reference Guide: HP Compaq dc7900 Business PC
Page 168
... back up the data from the old hard drive so that you do not have created a Recovery Disc Set to restore the operating system, software drivers, and any software applications that can transfer the data to the new hard drive. Figure 8-47 Removing the Carrier Cover 156 Chapter 8 Removal and ...Replacement Procedures Small Form Factor (SFF) Chassis To remove and replace a drive in the carrier: NOTE: Before you remove the old hard drive, be quickly and easily removed from the ...
... back up the data from the old hard drive so that you do not have created a Recovery Disc Set to restore the operating system, software drivers, and any software applications that can transfer the data to the new hard drive. Figure 8-47 Removing the Carrier Cover 156 Chapter 8 Removal and ...Replacement Procedures Small Form Factor (SFF) Chassis To remove and replace a drive in the carrier: NOTE: Before you remove the old hard drive, be quickly and easily removed from the ...
Using eSATA on HP Compaq dc7900 Business PCs
Page 8
... the system into Windows Vista. 6. It does not have an eSATA connector on the system board with a different chipset. c. The Intel AHCI driver can be downloaded from Native AHCI to a system with the external eSATA port located at the rear of the system. The following table provides the.... The eSATA connector is in the INF or the AHCI driver will fail and the system will not boot. Hardware Both SFF and CMT form factors of the eSATA cable has the standard SATA L-shaped connector. The system board end of HP Compaq dc7900 Business PCs have the SATA3 (Orange) connector. d.
... the system into Windows Vista. 6. It does not have an eSATA connector on the system board with a different chipset. c. The Intel AHCI driver can be downloaded from Native AHCI to a system with the external eSATA port located at the rear of the system. The following table provides the.... The eSATA connector is in the INF or the AHCI driver will fail and the system will not boot. Hardware Both SFF and CMT form factors of the eSATA cable has the standard SATA L-shaped connector. The system board end of HP Compaq dc7900 Business PCs have the SATA3 (Orange) connector. d.