Cisco CISCO775M-G2 - 760 ISDN Router Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco CISCO775M-G2 manuals!
Problems with Cisco CISCO775M-G2?
Ask a Question
Free Cisco CISCO775M-G2 manuals!
Problems with Cisco CISCO775M-G2?
Ask a Question
Popular Cisco CISCO775M-G2 Manual Pages
Installation Guide - Page 2
...installed and used in accordance with the instruction manual, may cause harmful interference to provide reasonable protection against harmful interference when the equipment is for FCC compliance of Class A devices: This equipment has been tested and found to part 15 of the FCC rules. IN NO EVENT SHALL CISCO... with Cisco's installation instructions, it off. These specifications are ...
Installation Guide - Page 9
... models. • Chapter 2, "Preparing for a person with your router to cable the router. Organization
The major sections of this guide can be acquired by reading general information on the Cisco Documentation CD-ROM in HTML format (Document Number DOC-782412=). About This Guide ix
About This Guide
The Cisco 700 Series Router Installation Guide provides hardware installation instructions...
Installation Guide - Page 10
...previous versions of the software are having trouble with your Cisco 700 series router:
• Release Notes for Cisco 700 Series Router Software provides the latest information on the Cisco Documentation CD-ROM and the Cisco Web site.
• Cisco 760 Quick Reference Guide and Cisco 770 Quick Reference Guide provide
hardware installation instructions, forms to the Cisco 700 series router.
Installation Guide - Page 34
... black power supply. • One black power supply cord. • One Cisco 700 Series Router Installation Guide. • One Documentation CD-ROM set. (The Cisco 700 Series Command Reference is on
Disk 2 of the CD-ROM set.)
• One Cisco 700 Quick Reference Guide. • One Cisco Fast Step CD-ROM. (The CD-ROM is inside the back cover...
Installation Guide - Page 49
... to a Cisco 765, Cisco 766, Cisco 775, or Cisco 776 router basic telephone service port (also known as "plain old telephone service" or "POTS" port). Note During a voice call . Do not touch the RJ-11 (phone) port wires... a Cisco 700 series router and how to configure the router to send and receive data. The ISDN telephone communicates over the same ISDN line the router uses to support that ...
Installation Guide - Page 56
... to put the call .
4-8 Cisco 700 Series Router Installation Guide To disable call waiting, use the dual tone multifrequency (DTMF) command, dialed on -hook (quickly press the telephone receiver button once) to determine if this is an example of the set callwaiting command that use the NET3 switch do not support ISDN provisioning for the analog...
Installation Guide - Page 59
...supported are using, you can disable the end-of-call function on the other end of -call is not established within a predefined period of a set internaltones command that enables the dial tone only:
766> set...Cisco 700 series routers to 1TR6 router software.
ISDN and Analog Telephone Devices 4-11
The set... for NET3 and 1TR6 ISDN Lines for Europe
Depending on the ISDN service provider,...
Installation Guide - Page 61
... digital and analog devices or have been instructed to do except power on the router.
Call Forwarding Busy
Activation: *67*forwarded-to number# Deactivation: #67# The switch type NET3 supports these features where the country group must be provisioned on the ISDN line for the service to be set for a list of Call Forwarding supplementary...
Installation Guide - Page 65
... Cisco 700 series router configurations. Troubleshooting Cisco 700 Series Routers 5-3
Communicating with the ISDN service provider.
• The SPIDs were not entered or were entered incorrectly. Enter or change the SPIDs by the ISDN service provider. Change the switch type by
using the set spid command or the Cisco 700 Fast Step Setup application. Terminal Identifier or SPID Problems...
Installation Guide - Page 66
... calls without any problems, but cannot receive incoming calls, check the following conditions:
• A telephone number was incorrectly configured by the ISDN service provider. Router Calls Itself
ISDN supports two separate logical data channels on -demand dialing is enabled or if the user issues the call command.
5-4 Cisco 700 Series Router Installation Guide Communicating with the...
Installation Guide - Page 89
... does not support hardware flow control.
Step 8 Click OK to the correct values, if you can test the connection by selecting File>Save As. Once it is created, you have problems, select File>Properties, and check the following. Troubleshooting the Terminal Connection
Although the balance of the 16550 UART chip and set this is...
Installation Guide - Page 91
...of the image contains features you intend to -date version available. You might want to update the image if
• The default image is the most up-to download the ... times.
The default image for all other Cisco 700 series routers is NET3, IR.
Downloading Software
The default image for Cisco 761, Cisco 765, Cisco 771, and Cisco 775 routers is US. Table B-2
Approximate ...
Installation Guide - Page 97
...the Integrated Service Digital ...models are implemented with your Cisco 700 series router. Data and Voice
The Cisco 765, Cisco 766, Cisco 775, and Cisco 776 routers support data and voice applications. However, there might be cases where you can configure your router by filling out the forms provided in the Cisco 700 Quick Reference Guide and following the instructions in the Cisco Fast Step Setup...
Installation Guide - Page 116
... DMS-100 switch C-9 ISDN BRI line C-1 to C-4 summaries C-6 to C-10 PSTN 6-3
Q
QIC-122 standard 1-5 quick reference guide xi
R
RAM 5-2, A-1 RD/RDY LED 1-11 release notes x Request For Comments (RFC) 1-9 RIP 1-9, 6-3
to support demand circuits 1-9 triggered extensions 1-9 Triggered RIP 1-3 RIVA 1-3 router damage, preventing 2-3 router manuals xi
Index 6
Cisco 700 Series Router Installation Guide
Installation Guide - Page 117
... image B-1 load command B-5
troubleshooting B-7 loading errors B-7 specifications A-1
SPIDs C-3 automatic SPID and switch detection 1-4 definition 6-3 setting SPIDs 5-3
stack revision C-4 Stacker LZ 1-5 StacLZS Compression 1-9 status message 5-8 stop bits A-3, B-2 supplementary service 1-5 support
Cisco ISDN Support Services C-6 Cisco Web site C-6 support demand circuits 1-9 suspended call...
Cisco CISCO775M-G2 Reviews
We have not received any reviews for Cisco yet.