Cisco 2503 Support and Manuals
Get Help and Manuals for this Cisco item
Popular Cisco 2503 Manual Pages
Getting Started Guide - Page 2
..., uses, and can be familiar with the instructions, may harm you install and minimally configure your Cisco 2504 Wireless Controller (2504 controller), which is part of each warning statement. The warnings below are general warnings that accompanied this device. Use the statement number provided at the end of the Cisco 2500 Series Wireless Controllers. These limits are provided in the...
Getting Started Guide - Page 3
...to 50 lightweight access points in conjunction with four 4 Gigabit Ethernet ports.
3
The 2504 controllers supports up to provide system-wide wireless LAN functions. As a component of the Cisco Unified Wireless Network (CUWN), the 2504 controller provides real-time communication between 32 to 104° F (0 to 40° C), taking into account the elevated temperatures when installed in...
Getting Started Guide - Page 4
... LAN connection to Cisco 2500 Series Wireless Controllers are not currently supported. To best use straight-through or crossover cables.
The controller has an auto MDI feature, so you can use this guide, you should have already designed the wireless topology of your network and have a working knowledge of access points to main office
10/100/1000BASE-T MDI cables
Access point connections...
Getting Started Guide - Page 5
... configures the RS-232 port as a console port with default settings of the LED manufacturer's specifications and is expected that there will default to unit.
A default baud-rate recovery mechanism is within the normal range of 9600, N, 8, 1. Note
It is not a defect. Figure 2 Front Panel and LEDs
282249
CONSOLE
CONSOLE
CISCO 2500 Series WIRELESS CONTROLLER
RESET
Model 2504...
Getting Started Guide - Page 9
...-head screws for damage. 2 Unpacking and Preparing the Controller for Operation
Follow these steps to unpack the 2504 controller and prepare it .
Controller with factory-supplied power cord and mounting hardware -
Network, operating system service network, and access point cables as required • Command-line interface (CLI) console - Ensure that all packing materials to the shipping...
Getting Started Guide - Page 10
... your wireless LAN or network administrator:
• A system (controller name), such as rfgrp40 if required. Cisco uses an integral TFTP server. An SSID can be the same.
• A management interface (DS Port or network interface port) IP address, such as 10.40.0.4. • A management interface netmask address, such as 255.255.255.0. • A management interface default router...
Getting Started Guide - Page 11
...or refer to the Cisco Wireless LAN Controller Configuration Guide for this installation.
For maximum reliability, mount the controller while following these guidelines:
• Make sure you can reach a 100 to 240 VAC grounded electrical outlet.
3 Installing the Controller
This section includes the following installation procedures: • Mounting the Controller, page 11 • Connecting...
Getting Started Guide - Page 13
... mounted on a shelf or desk, perform the following tasks to complete the installation:
• Connecting the Controller Console Port • Securing the Power Adapter Cable • Connecting to the Network
For configuration instructions about using the CLI setup program, see the "Running the Bootup Script and Power-On Self Test" section on a wall using rack-mount brackets, follow...
Getting Started Guide - Page 21
... 3
Plug the RJ-45 connector on a null-modem serial cable into the controller console port and the other end of the cable into the serial port of the PC. Start the PC terminal emulation program. Caution
If the relief clip is not installed, the power connector can configure the 2504 controller for the following parameters:
• 9600 baud • 8 data...
Getting Started Guide - Page 25
...: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services: ok Starting LWAPP: ok Starting CAPWAP: ok Starting LOCP: ok Starting Security...
Getting Started Guide - Page 27
... selected Validating XML configuration octeon_device_init: found 1 DPs /dev/fpga: No such device or address readCPUConfigData: cardid 0x6060001 Cisco is a trademark of Cisco Systems, Inc. Software Copyright Cisco Systems, Inc. Format FLASH Drive 6. Active 2. Manually update images
Enter selection:
If you did not press Esc, the boot process continues and takes two to access the following menu...
Getting Started Guide - Page 30
... the access point manager interface. You can enter up to 31 ASCII characters. Ports values are 1 to this controller. Enter the IP address of the management interface netmask.
Enter the IP address of the management interface (a valid VLAN identifier or 0 for each . Enter the administrative password to be assigned to match the switch interface configuration. You...
Getting Started Guide - Page 34
...
10/100/1000BASE-T MDI cable
282298 You can set the automatic logout from 0 (never log out) to 160 minutes using double quotation marks. Figure 13 External Network Equipment Connection to the Controller
10/100/1000BASE-T MDI cable
Cisco Access Points
CLI console
Connection to the controller.
The connection uses 10/100/1000BASE-T Ethernet (RJ-45 physical port, UTP, Category-5 or higher...
Getting Started Guide - Page 35
... is operational, the controller is available to Cisco 2500 Series Wireless Controllers are scanning for a controller. You have configured the controller, use Category-5, Category-5e, Category-6, or Category-7 Ethernet cables to connect up to 50 Cisco lightweight access points to the controller Ethernet ports or to the Cisco Wireless LAN Controller Configuration Guide for basic operation...
Getting Started Guide - Page 36
...boots. The guide is complete. To reset the controller using the Reset button, follow these steps:
Step 1 Connect a PC to the controller console point.
36 See Table 1 on page 5 for more information about configuring your 2504 controller is not working properly, check the LEDs on cisco.com. Figure 14 Access Points Connected to a Controller
Network
Cisco 2504 Wireless Controller
10/100...
Cisco 2503 Reviews
We have not received any reviews for Cisco yet.