Acer PD726 Support and Manuals
Popular Acer PD726 Manual Pages
User Manual - Page 4
... the software 37
Connecting to a projector 39 Using the audio function 40 Configuring your Acer WPG 42
Projector ID ...42 Configuration password setup 42 Upgrade firmware ...44 Network settings ...44 Projection controls 45 Hide ...45 Freeze ...45 Projector remote control 45 Hotkey explanation...45
Appendices 46 Troubleshooting 46 Replacing the lamp 49 Specifications...51...
User Manual - Page 5
... eyes.
This product will not turn back on until the lamp module has been replaced.
To replace the lamp, follow all warnings, precautions and maintenance as this user's guide to change the lamp when it will burn out and may hurt your unit.
WarningWarningWarningWarningWarning-
When changing the lamp, please allow unit to cool down, and follow the procedures...
User Manual - Page 7
...High-tech HDMI and DVI connection for digital signal
which supports 480p, 576p, 720p and 1080i formats
u User friendly and powerful Acer Empowering key
including: Acer eView Management, Acer eTimer Management and Acer eOpening Management. Introduction
Product Features
This product is an XGA single chip 0.7" DLP® projector. u Full function remote control with laser pointer u Advanced digital...
User Manual - Page 16
... the on -screen display. on the on -screen display.
Installation
Powering off the projector
1. Press the "Power" button to turn off the projector lamp, you must wait until the projector has completed the cooling cycle and has entered standby mode. Please contact your local reseller or service center.
When the "TEMP" indicator lights solid Red...
User Manual - Page 22
...parts of the image. Color 4 Press "Color" to S-Video source. Component
4 Press "Component" to change source to the projector via "Acer eProjection Management" utility. This connector can
support to component connector. Wireless (For PD726W...This
connector supports Analog RGB, YPbPr (480p/576p/720p/ 1080i), YCbCr (480i/576i) and RGBsync. User Controls
English ... 20
RGB
4 Press...
User Manual - Page 26
... vertically
and makes a squarer image. Projection
4
Front-Desktop
The factory default setting.
4
Front-Ceiling
When you select this function, the projector turns the
image upside down for ceiling-mounted projection.
4
Rear-Desktop
When you can project behind a translucent screen. User Controls
Image (Computer / Video Mode)
English ... 24
H.
V. Keystone (Vertical Keystone...
User Manual - Page 28
... utility (refer to dim the projector lamp which is down loaded
from one to another, when you exit the OSD menu, the new setting will take effect.
4 Acer : The default startup screen of below section). Auto Shutdown
The projector will auto shutdown while there is no signal input after the setting time. User Controls
Management (Computer / Video...
User Manual - Page 29
... "Yes "to turn the lamp hour counter to enter "Download Mode". 1. Please make sure the USB cable has been plugged and connected to your PC to their desired image. Before the download starts, the projector must enter "Download Mode" first.
You can install Acer eOpening Management from your projector. Please follow the instruction below to 0 hours...
User Manual - Page 33
... the display parameters on all menus to the Unlock ID.
3.Once the new "Administrator Password" retrieved from Acer has been logged into the projector, old "Administrator Password" will give you new Administrator Password according to the factory default settings. Reset
2.Write down the "Unlock ID" and contact with Acer service center. English
They will be replaced by the new...
User Manual - Page 41
... (they may also choose to assign a specific SSID to that projector, indicating, for example, the number of the room in which the projector is enabled (refer to "Configuration" later in this guide). if another user wishes to use the projector, you will be in different rooms), and the feature is installed (refer to "Configuration" later in this...
User Manual - Page 46
... IP address, or manually set a customized SSID to check if there is any newer firmware available. You can also change the network settings. Upgrade firmware Click on this link to identify the Acer WPG.
If necessary, you can set the RF channel used to connect with an open Internet connection to change or delete the password by clicking Configuration password setup.
User Manual - Page 48
Appendices
Troubleshooting
If you experience trouble with the projector, refer to the following steps.
4. Follow the above steps 1-2. Please
Make sure you use a PC:
If the resolution of connectors are not crooked or broken.
Check if the projection refer to the following information. Problem: Partial, scrolling or incorrectly displayed image.
Press "Re...
User Manual - Page 49
...distance 3.94
to page 25. Change the monitor color setting from the projector.
47 ... Problem: Image has vertical flickering bar
Use "Frequency" to... the resolution setting of the monitor display is out of your computer's documentation for information on "Show all the equipment and the projector. Appendices
6. Then select "Standard monitor types" under the "Models" box.
...
User Manual - Page 50
... type on your DVD player, please
select 4:3 aspect ratio in the "Replacing the Lamp". Problem: Image is reversed.
Select "Image" from See page 24, 25. To replace the lamp, follow the procedures in the on Power off (Cooling) Error (Lamp fail)
Error (Thermal fail) Error (Fan lock fail) Error (Over Temp.) Error (Lamp Breakdown)
Light On
Power LED Temp LED...
User Manual - Page 53
...: For projector remote control
- Audio Output: One phone jack for wireless audio output
(for VGA, component and HDTV signal
- FCC Class B, CE Class B, VCCI-II, ETL, cETL, ETL-GS,
C-tick, PSB, PSE, CB Report, CCC
51 ... Light Valve Lamp Number of component input
- Frequency V. Single Chip DLP® Technology by Texas Instruments
- 300 W User Replaceable Lamp...
Acer PD726 Reviews
Do you have an experience with the Acer PD726 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Acer yet.
Earn 750 points for your review!