eMachines EL1358G Support Question
eMachines EL1358G Support Question
Find answers below for this question about eMachines EL1358G.Need a eMachines EL1358G manual? We have 1 online manual for this item!
Question posted by sonjaoliver on February 18th, 2013
Battery Location
Where is the battery located?
Current Answers
Answer #1: Posted by tintinb on February 21st, 2013 8:43 AM
tintinb
Member since:
October 26th, 2012 Points: 7,056,560
Member since:
October 26th, 2012 Points: 7,056,560
I believe that you are referring to the CMOS battery of your eMachines EL1358G. It is because this is the only battery inserted on any desktop computer. The CMOS battery is located somewhere on your keyboard. You can see a small round shiny battery in the motherboard. I also provided the supporting image below to show the image of CMOS battery.
Read the user's manual here for further information.
http://www.helpowl.com/manuals/eMachines/EL1358G/114380
If you have more questions, please don't hesitate to ask here at HelpOwl. Experts here are always willing to answer your questions to the best of our knowledge and expertise.
Regards,
Tintin
Supporting Images
You can click the images below to enlarge
Related eMachines EL1358G Manual Pages
eMachines EL1358 Service Guide - Page 2
Date
Chapter
Updates
ii
EL1358 Service Guide
Revision History
Refer to the table below for changes made on this version of the EL1358 Desktop Computer Service Guide.
eMachines EL1358 Service Guide - Page 15
... configuration error is detected by the system and you repeatedly receive "Run Setup" messages, the RTC battery located on the mainboard (BT1) may be defective. If the values and the actual hardware do not ...in this case, the system cannot retain configuration values in a battery-backed nonvolatile memory called CMOS RAM. IMPORTANT If you are already properly configured and optimized, there ...
eMachines EL1358 Service Guide - Page 30
Remove the two screws located on the rear edge of the side panel.
2. Slide the panel back about 2.5 cm (1.0 in) to release it from the chassis notches, then detach the panel from the chassis.
3. Disassembly Procedures
Removing the Side Panel
1. Put the side panel aside for reinstallation later. 22
EL1358 Service Guide
eMachines EL1358 Service Guide - Page 48
Please detach the RTC battery and follow local regulations for disposal.
40
EL1358 Service Guide 2. Note:RTC battery has been highlighted with the yellow circle as above image shows. Lift the board from the chassis.
3. Remove the RTC battery.
eMachines EL1358 Service Guide - Page 49
... System Check" procedure on the next section and the "Beep Codes" section on the front panel.
Go to "Front View" section on page 4 for the location and description of the failure is set to recreate the failure by running the diagnostic tests or repeating the
same operation. 3.
eMachines EL1358 Service Guide - Page 52
.... Early POST initialization of chipset registers.
Uncompress all the output devices. Initialize System Management Interrupt. Initializes different devices. Check CMOS diagnostic byte to determine if battery power is OK and CMOS checksum is initialized at this checkpoint. Activate ADM module. USB controllers are initialized at this point.
Set the window for...
eMachines EL1358 Service Guide - Page 59
... using AMIBIOS Setup. It could also appear when the user intentionally discharges the CMOS battery.
Keyboard is not present or the hardware is not responding when the keyboard controller ... data has been changed by a program other than the BIOS or that the CMOS battery needs to malfunction. Keyboard controller failure.
Miscellaneous
Message Displayed KBC BAT Test failed
Keyboard ...
eMachines EL1358 Service Guide - Page 62
... PCI modem, make sure Power on By Ring in cable from modem adapter card is configured correctly for your modem and set correctly.
• RTC battery • Mainboard
Audio-related Symptoms
Symptom/Error Audio software program invoked but has no sound comes from suspend mode. Real-Time Clock-related Symptoms
Symptom...
eMachines EL1358 Service Guide - Page 63
... to the service manual for the power cable) is not set to Instant-off. • Power switch cable assembly
• Ensure the power override switch (located at the back of the computer, just above the connector for the printer.
Printer-related Symptoms Symptom/Error Printing failed. Printer problems.
Action/FRU
•...
eMachines EL1358 Service Guide - Page 70
... set it over the 2-3 pins for 20 to turn on the computer. 14. Return the jumper block to the system. 13. Remove the side panel. 6. Locate the JBIOS1 jumper on a flat, steady surface. 5. Connect the AC power cord to its default 1-2 position. 10. During POST, press Delete to load the system...
eMachines EL1358 Service Guide - Page 73
... caps are numbered. Jumpers with more than one pin are placed on pins 1 and 2 to close or short the jumper. The following illustration shows the location of the main board. Place the jumper cap on pins 2 and 3 to turn off the system.
eMachines EL1358 Service Guide - Page 96
... check type/speed 10 specifications 82 troubleshooting 52 PSU, see power supply unit 32
R
Return Merchandise Authorization 73 RMA, see Return Merchandise Authorization 73 RTC battery
BIOS error 7 RTC clock
troubleshooting 54
S
Save & Exit Setup 19 side panel
remove 22 slots
expansion 5 software specifications
antivirus 2 operating system 1 specifications
Similar Questions
Battery For Emachine
Where is the battery located on a desktop emachine PC model EL1352-07e
Where is the battery located on a desktop emachine PC model EL1352-07e
(Posted by mottosam 8 years ago)
Bios Battery Location And Numbers To Order New One
Looking for diagram for emachines EL1358G-51w showing location of little bios battery and the number...
Looking for diagram for emachines EL1358G-51w showing location of little bios battery and the number...
(Posted by ljett 8 years ago)
I Need To Restore My Model El1358g. Where Do I Get The Restore Disk, Please.
I need to restore my model EL1358G. Where do I get the restore disk, please.
I need to restore my model EL1358G. Where do I get the restore disk, please.
(Posted by furgeson 8 years ago)
