eMachines EL1300G Support Question
eMachines EL1300G Support Question
Find answers below for this question about eMachines EL1300G.Need a eMachines EL1300G manual? We have 2 online manuals for this item!
Question posted by rfull4 on September 29th, 2020
No Sound Or Boot When Power Switch Pressed.
Unfortunately the suggestions made by techygirl did not work. I have verified the power cord, all connectors and connections, the power supply was swapped out with another, no success. The power switch was verified as good, but there is no drive light.The hard drive was verified as good.Is it possible that a surge damaged the MB. I am running out of options.
Current Answers
Answer #1: Posted by Troubleshooter101 on October 2nd, 2020 10:20 PM
Troubleshooter101
Member since:
September 30th, 2015 Points: 2,927,070
Member since:
September 30th, 2015 Points: 2,927,070
THE Fact is upon checking different internet forums it means that the motherboard of this machine is failed and due to that its not working. So the solution is to change motherboard.
Thanks
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Troublshooter101
Related eMachines EL1300G Manual Pages
eMachines Setup Guide - Page 3
... overheating. Do not locate this product from the type of all warnings and instructions marked on the cord.
• If an extension cord is properly grounded before inserting the AC adapter plug. Make sure the power outlet is used , the load should never be blocked by plugging in a fire or electric shock. Keep...
eMachines Setup Guide - Page 4
...Use the product only with the supplied power supply cord set , make sure that the new power cord meets the following the operating
instructions ... product to replace the power cord set . Refer all telephone lines from lightning, do not connect the telephone line to ... good protection from unexpected noise produced by other controls may result in damage and will often require extensive work ...
eMachines Setup Guide - Page 10
... card reader 36 Modem (cable or DSL 36 Modem (dial-up 36 Monitor 40 Mouse 41 Networks 42 Optical disc drives 42 Passwords 44 Power 44 Printer 44 Sound 46 Recovering your system 47 Creating recovery discs 48 Recovering pre-installed software and drivers . 49 Returning your system to its factory condition...
eMachines Setup Guide - Page 12
...Press this guide may look different than your model of computer.
Plug a microphone into this jack. This jack is turned on. Insert a memory card from a digital camera, MP3 player, PDA, cellular telephone, or other device into these ports. You can also configure the power...
Icon
DVD/CD drive
Memory card reader
Power button/power indicator
USB ports
Microphone jack Headphone jack
...
eMachines Setup Guide - Page 13
... jack (green plug) -ORFront speakers jack
PS/2 mouse port
Ethernet (network) jack
Description
Connects to the correct voltage for your front left and right speakers into this is set to a Kensington-compatible computer security lock. Plug the power cord into this connector.
Make sure that this jack.
Plug a PS/2 keyboard into this port. This...
eMachines Setup Guide - Page 18
... system board, add-in cards, and peripheral devices. To set the voltage to 115V or 230V.
The switch is operating in the United States. In other areas of your computer, near the power cable connector. The power supply's voltage selection for your location before turning on the back of your computer to set the voltage...
eMachines Setup Guide - Page 25
... Ethernet network hardware
Making sure your broadband connection works Important
If you must install one.
If one is not listed, you do not have for
additional network hardware
• DHCP server/dynamic IP address assignment to ISP. Broadband Internet settings differ from unwanted intruders
• 4-port switch to eliminate the need for setting...
eMachines Setup Guide - Page 27
..., the corresponding green indicator should light on the front of the router, indicating a good connection. 4 Repeat 3 for each computer is connected to the DSL or cable modem and is identified by a label or a switch. As each computer you want to connect to the network. Plug the other end of a straight-through network cable into the...
eMachines Setup Guide - Page 30
...; Contact your Internet service provider.
20 Take any actions suggested.
• If you are using a wired Ethernet network, check
all physical cable connections.
• Make sure that your home network is
plugged....
• Temporarily turn off any firewall software on
your desktop computer.
• Turn off all of the devices, then power them back
on the left of your router or access point...
eMachines Setup Guide - Page 33
...: 1 Click (Start), then click Network.
The Control Panel window opens. 2 Under Hardware and Sound, click Printer The Printers window opens. 3 Right-click the name and icon of the computer containing... 1 Click (Start), then click Control Panel. Type workgroups in the Search Help box, then press ENTER. Using the network
After the drives and printers on network discover and file sharing. 3 ...
eMachines Setup Guide - Page 38
... procedures you performed and make sure that you use a power strip or surge
protector, make sure that it is turned on.
• If a peripheral device (such as a keyboard
or mouse) does not work, make sure that all connections are listed in the Search box, then press ENTER. Type troubleshooting in alphabetical order.
28
Help...
eMachines Setup Guide - Page 39
... all computers are working. CD or DVD drives
See "Optical disc drives" on page 46. Most routers have lights that you have the same workgroup name.
29
For more information, see the documentation that your Ethernet cable is
plugged into
a powered electrical outlet and turned on your computer. Audio
See "Sound" on page...
eMachines Setup Guide - Page 45
...computer.
• Remove all extension cables and switch
boxes.
• Clean the keyboard by using it again. If the keyboard does not work
• Make sure that you know works to drain it.
Let the keyboard dry ...that might be stuck, then restart your computer and unplug the keyboard. Press
each key to
help determine if a memory module is not stuck. Keyboard
The keyboard does not...
eMachines Setup Guide - Page 47
....
These lines do not work correctly. Type dialing in the Search box, then press ENTER.
• Disconnect any answering machine, fax
machine, or printer that you are not using your Control Panel is a common problem that the connectors are free from corrosion and all settings are secure.
Do not connect these devices to the...
eMachines Setup Guide - Page 50
..., then click the Modems tab.
3 Click the modem you can turn down the modem volume. You may hear unusual handshaking sounds when the modems first connect.
If the monitor is turned on, the power LED should be lit.
• Adjust the brightness and contrast
controls to the video port on . Monitor
40
The...
eMachines Setup Guide - Page 51
• Reinstall the device driver. • Connect a monitor that you know works
to your monitor and video card documentation. Type screen resolution in correctly.
• Shut down and restart your computer. • Remove all extension cables and switch
boxes.
• Try a mouse you know is dim or difficult to read
• Adjust the brightness...
eMachines Setup Guide - Page 54
To test the outlet, plug a working correctly.
Printer
The printer will not turn on .
• Make sure that the power cord is free
from cuts or damage.
Replace any damaged cables. Power
Your computer will not turn on
• Make sure that the power cord is
connected to an AC power source and to your computer, and that your...
eMachines Setup Guide - Page 56
..., click Start, then click Help and Support. Type sound troubleshooter in the Search box, then press ENTER. You see the
speaker setup poster to check your speaker connections.
• Make sure that you want to add additional memory to the printer.
Most printers have been printed before
sending additional files to the printer...
eMachines Setup Guide - Page 61
... Recovery Management screen shows you inserted.
51 The boot menu is where you to restart your hard drive.
3 Click Next to select CDROM/DVD, then press ENTER. Windows installs from , such as the hard...disc.
3 Use your hard drive. Your computer restarts. 6 Follow the on your computer, then press ALT+F10
during startup. This process will erase all pre-installed software and drivers: 1 Turn on ...
eMachines Setup Guide - Page 69
In many cases, additional product information and online documentation for eMachines-supplied hardware can be found in the Search box, then press ENTER.
59 Warning
To avoid bodily injury, do not attempt to information about Windows, click Start, then...:
• The printed or online documentation
that your computer is nearby
at the time of your call.
Power cords or plugs are damaged -
Similar Questions
El1300g-when Power Button Pressed, Fan Comes On, And Hard Drive Runs. No Output
power supply is good, hard drive is good, no light in power switch. No display . tried using new win...
power supply is good, hard drive is good, no light in power switch. No display . tried using new win...
(Posted by rfull4 3 years ago)
No Boot Or Sound When Power Button Is Pressed.
When the power button is pressed, the internal fan comes on. nothing else happens. no light, no outp...
When the power button is pressed, the internal fan comes on. nothing else happens. no light, no outp...
(Posted by rfull4 3 years ago)
How To Wire Power Switch On Emachine W3644 Desktop To Win Fast Motherboard
(Posted by ffmiked2 9 years ago)
How To Replace The Power Switch
how to replace the power switch
how to replace the power switch
(Posted by Anonymous-102391 11 years ago)