Weider Pro 8900 Support Question
Weider Pro 8900 Support Question
Find answers below for this question about Weider Pro 8900.Need a Weider Pro 8900 manual? We have 1 online manual for this item!
Question posted by patoro969 on September 10th, 2019
Weider Pro 8900
Hello,Do universal weights fit Weider pro 8900?Thank you
Current Answers
Related Weider Pro 8900 Manual Pages
English Manual - Page 1
Serial Number Decal
WEIGHT SYSTEM EXERCISER Userʼs Manual
• Assembly • Operation • Maintenance • Part List and Drawing
Sears, Roebuck and Co. Model No. 831.14923.1 Serial No.
Keep ...
English Manual - Page 2
... in the location shown. TABLE OF CONTENTS
WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 PART IDENTIFICATION CHART 5 ASSEMBLY 7 ADJUSTMENT 34 WEIGHT RESISTANCE CHART 37 CABLE DIAGRAM 38 MAINTENANCE 39 EXERCISE GUIDELINES 40 PART LIST 43 EXPLODED DRAWING 45 ORDERING REPLACEMENT PARTS Back Cover 90-DAY FULL WARRANTY Back Cover
WARNING DECAL...
English Manual - Page 3
... to protect the floor or carpet. Never release the arms, leg lever, lat bar, handle, ankle strap, or double strap while weights are exercising, stop immediately and cool down.
3 IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and ...
English Manual - Page 4
..., note the product model number and serial number before using the weight system. To help you for selecting the versatile WEIDER PRO™ 8900 weight system. BEFORE YOU BEGIN
Thank you to develop every major muscle group of the body.
The weight system offers a selection of weight stations designed to achieve the specific results you have questions after...
English Manual - Page 7
... information and instructions:
• Assembly requires two persons.
• Because of its weight and size, assemble the weight system in the location where it will be more convenient if you have a socket ...one Phillips screwdriver
Assembly may be used. Attach the Side Stabilizers (2) to walk around the weight system.
• Place all parts in the box above. Do
not overtighten the Screws...
English Manual - Page 11
10. Attach each Weight Guide with an M10 x 63mm Bolt (89) and an M10 Locknut (74). Holes 31
74
74
1
89
11
Orient the Weight Guides (31) so that the indicated holes are closer to the floor.
10
Insert the Weight Guides (31) into the holes in the Base (1).
English Manual - Page 12
... 28
12. Make sure that the notch is inserted into the notch in the indicated location.
11
Slide the Bottom Cover (28) downward over the Weight Guides (31) and the Burn Cable (45). 11.
English Manual - Page 13
...) so that the pin hole is in the indicated location.
Slide the Top Cover onto the
14
27
Top Frame.
6
15. Then, slide the Weight (30) onto the Weight Guides (31). Do not fully
tighten the Locknuts yet.
74
88 6
63
13
63 5 Orient the Top Frame (6) and the Top Cover (27...
English Manual - Page 14
..., the Top Cover (27) is not shown.
17
Route the Burn Cable (45) over two Burn Pulleys (68). Attach each Burn Pulley (68) to the Weight
16
Guides (31) with an M10 x 40mm Bolt (97) and an M10 Locknut (74).
74
86
86
6
65
65
31
74
68
68
45
6
97...
English Manual - Page 25
...of the High Cable (44) through the upper end of Weights (30).
45
Lift the top Weight (30) upward, and tap a Roll Pin (37) into the Weight Selector (32) in the indicated location.
44 A 45...the High Cable (44) at least five complete turns into the Weight Selector (32). Tighten the Nut (A) against the Weight Selector (32).
45. Insert the Weight Selector (32) into the stack of the Burn Cable (45...
English Manual - Page 26
46. Insert the Weight Pin (41) under a Weight (30).
46
30 41
47. Orient the Seat (24) and a Cushion Frame (9) as shown.
48
24
Attach the Seat (24) to the Cushion Frame (9) with four M6 x 16mm Screws (62).
9 62
62
26 Insert the Lock Pin (39) through a Weight Guide (31) and secure the Lock (38) into the Lock Pin.
47
31 38
39
48.
English Manual - Page 33
.... 61. Insert a Pulley (69) under the High Cable (44) in the cables, you will be damaged when heavy weight is any slack in the location shown.
61
Attach the Pulley (69) inside the Top Frame (6) with an M10 x...73), and an M10 Locknut (74).
74 88 73 69 44
6 73 88 75
62. Before using the weight system, pull each cable a few times to the High or Low Anchor (C, D) on page 38 for proper ...
English Manual - Page 34
... in the Cushion Frame (not shown).
Make sure that the Adjustment Knob is used. Turn the bent end downward. Use the WEIGHT
41
RESISTANCE CHART on page 40 for several exercises. ADJUSTING THE SEAT, THE BACKREST, AND THE LEG LOCK FRAME
To adjust the Seat (24), remove the Adjustment Knob (29), move...
English Manual - Page 35
...attach the hook to the Top Frame (6).
See the WEIGHT RESISTANCE CHART on the Burn Cable (45). Adjust the length of resistance added by the burn band at each exercise station.
44 50
47
6
26 45 Slot Hook... be attached at the ab station or the low pulley station in the correct starting position for the exercise to be performed. Then, insert the Burn Cable into the slot on the Burn Band. When the...
English Manual - Page 36
... a footrest, rotate the Foot Plate downward so that it is flat on the floor.
4
LOCKING THE WEIGHT STACK To lock the weight stack after each workout, insert the Lock Pin (39) through one of the Weight Guides (31), and secure the Lock (38) into the Lock Pin.
31 38
39
36 When you...
English Manual - Page 37
... the butterfly arm station is for each exercise station.
WEIGHT RESISTANCE CHART
The chart below shows the approximate weight resistance at each station may vary due to differences in the left column refer to the 12.5-lb. The actual resistance at each arm. WEIGHT RESISTANCE WITHOUT BURN BAND
WEIGHT
1 2 3 4 5 6 7 8 9 10 11 12
AB STATION BUTTERFLY...
English Manual - Page 40
... measurements once a month. WORKOUT GUIDELINES
Familiarize yourself with 5 to workout. Perform the repetitions in each exercise and move only the appropriate parts of the body. Exhale during the return stroke.
When you perform.
Weight Loss-To lose weight, use a low amount of resistance and increase the number of repetitions in each repetition should...
English Manual - Page 41
... your workouts will help you to make exercise a regular and enjoyable part of this page, and use the copies to schedule and record your life.
Exercise
Lbs. Sets Reps Time Distance Speed
41
Lbs. Sets Reps
2.
7.
3.
8.
4.
9.
5.
10.
Sets Reps Exercise 6. 7. 8. 9. 10. Sets Reps Exercise 6. 7. 8. 9. 10. Sets Reps Exercise 6. EXERCISE LOG
Make copies of your strength and...
English Manual - Page 44
... 1
110 1
*
-
*
-
*
-
*
- Qty. Lat Bar Foam Grip Lat Bar Cap Plastic Bushing Handle M4 x 12mm Bolt M4 Locknut Containment Bracket Left Side Shroud Userʼs Manual Exercise Guide Grease Packet Assembly Tool
Note: Specifications are not illustrated.
44 If a part is missing, please call 1-877-992-5999. *These parts are subject to...
English Manual - Page 48
..., LLC ® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
90-DAY FULL WARRANTY
If this Sears WEIGHT SYSTEM EXERCISER fails due to a defect in your home or ours! For Sears professional installation of carry-in China © 2012 ICON IP, Inc. This warranty does...
Similar Questions
I Need A Replacement Cable For My Welder Pro 8900 Do You Guys Carry One?
(Posted by mjdunkin21 3 years ago)
Hello, Where Can I Find A Cable For My Welder Pro 9635 ? Thanks For Your Answer.
hello, where can I find a cable for my weider pro 9635 ? I have had it for few years and the cable f...
hello, where can I find a cable for my weider pro 9635 ? I have had it for few years and the cable f...
(Posted by Nathaliebrachet 4 years ago)
Can You Show Me Page 31 Of The Weider Pro 9930 Manual
can you show me page 31 of the weider pro 9930 manual
can you show me page 31 of the weider pro 9930 manual
(Posted by rdnehus 10 years ago)
How Do U Assemble The Pulleys On The Weider Pro 8900 Instructions Not Clear
the diagram in the manual looks nothing like the actual machine is there a better way to see this di...
the diagram in the manual looks nothing like the actual machine is there a better way to see this di...
(Posted by carmen011374 10 years ago)
Weider Pro 8900 Pulley Position/tension.
Pulley's 3-6 do not seem to be set up correctly. I have them exactly as they are in the book, howeve...
Pulley's 3-6 do not seem to be set up correctly. I have them exactly as they are in the book, howeve...
(Posted by djbillbraun 11 years ago)