Weed Eater WE EL-15TNE Support Question
Weed Eater WE EL-15TNE Support Question
Find answers below for this question about Weed Eater WE EL-15TNE.Need a Weed Eater WE EL-15TNE manual? We have 2 online manuals for this item!
Question posted by SMGMICKEY on May 31st, 2021
I Need To Replace The Head Assembly. How Do I Do That?
How
Current Answers
Answer #1: Posted by Odin on May 31st, 2021 10:08 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Weed Eater WE EL-15TNE Manual Pages
Owner Manual - Page 2
...of electrical shock. • Use a voltage supply as suitable for line trimmer use and replace if damaged.
Inspect extension cord before using electric gar- If in the OPERATION section). •....
Never carry unit with loosely hanging ties, straps, tassels, etc. Watch what you need assistance, call 1-800-554-6723. Always wear safety
glasses or similar eye protection when ...
Owner Manual - Page 3
...can cause the double insulation construction
to
this unit, including housing, switch, motor,
locking sleeve assembly, wires, etc., must be recommended by
the manufacturer. Store unit unplugged. • Do ...so the line limiter blade (on circuit or outlet to plug movement (see USER REPLACEABLE SERVICE PARTS in cutting head. • Do not overreach or stand on and off properly. Do not ...
Owner Manual - Page 4
...operator and/or damage to the operator including electrocution. NOTE: If shield is properly assembled and all assembly steps to ensure your unit is not properly installed, damage to unit (including ...
Tube
Option 1
Option 2
5.
ATTACHING EDGE GUIDE AND SHIELD
WARNING: The shield must be assembled as illustrated below. Your unit is sharp and can be positioned on shield prior to the ...
Owner Manual - Page 5
...Twist and Edge Button Motor Housing
Cord Retainer
Clamp Recessed
Plug
Locking
Sleeve
Assembly
Air Vents
Debris Shield
Edge Guide
Trimmer Head with the location of the unit into shield and motor housing as ...LIMITER BLADE The LINE LIMITER BLADE cuts the cutting line to rotate and the line is assembled to the unit as shown.
EDGE GUIDE The EDGE GUIDE protects the unit from contacting...
Owner Manual - Page 6
... the handle and around the hook as shown.
tion.
Without bending over the trimmer head. Cord Retainer Extension Cord CORRECT OPERATING POSITION
ADJUSTING TRIMMER HEIGHT The height of cutting line... past the line limiter, too much line is at the desired length.
6 The tube will need to the TROUBLESHOOTING TABLE. sist handle with the automatic line feed, refer to be heard, more...
Owner Manual - Page 7
...and become a dangerous missile that can cause serious injury.
Other sizes and shapes of the trimmer head about 3 inches (8 cm) above the surfaces being swept and move the tool from side to ... ground and damage the tool.
Avoid pressing the head into work area. Mowing
EDGING POSITION While holding the trimmer in places conventional lawn mowers cannot reach. Keep the line parallel to...
Owner Manual - Page 8
... line into hub with eyelet (see illustration). WARNING: Never use , inspect complete unit for replacement of unit if debris shield is damaged. BEFORE EACH USE
CHECK FOR LOOSE FASTENERS AND PARTS • Housing Screws • Locking Sleeve Assembly • Assist Handle • Debris Shield • Edge Guide
CHECK FOR DAMAGED OR WORN...
Owner Manual - Page 9
... PARTS REPLACEMENT PART Spool with 0.065 inch Trimmer Line Assist Handle Bolt Carriage, M6 X 1 Knob Clamp
Shield Assembly
Edge Guide Spool cap Bolt
PART NUMBER 952711920 574495601 574495901 574473101 574495801
574495401 574491601 574492201 574471601
STORAGE
WARNING: Perform the following
steps after each use . • Carry the unit with tip of head.
2. forming all...
Owner Manual - Page 10
...set-up or normal adjustments explained in material and workmanship and agrees to repair or replace under this warranty any defective WEED EATER brand electric or cordless product within two ...not transferable and does not cover damage or liability caused by WEED EATER for repair or replacement at any time without notice or obligation to any unanswered questions concerning this warranty, please ...
Parts List - Page 1
Description
Not Shown 115254226 Manual
= New Part Number For This IPL
= Refer to design changes. MODEL
WE EL-15TNE
Page: 1
2 43
1
WARNING
All repairs, adjustments and maintenance not described in the Operator's Manual must be ... 574495401 8. 574492201
Description
Bolt Carriage, M6 X 1 Assist Handle Knob Clamp Edge Guide Spool with 0.065" Trimmer line Shield Assembly Spool Cap
Ref.
Similar Questions
Spool Spindle Fit
Model WE EL-15TNE should spool fit tight on spindal, I inherited item, and don't know , works but wo...
Model WE EL-15TNE should spool fit tight on spindal, I inherited item, and don't know , works but wo...
(Posted by jimolbrych 5 years ago)
How To Remove And Change Out Cutter Head On We El- 15tne
How To Remove The String Head And Replace On Trimmer
How To Remove The String Head And Replace On Trimmer
(Posted by GMM203 6 years ago)
How Long Should The Replacement Fillament Line Be To Be Rewinded? 10, 25, ?
(Posted by javiervalenciano 8 years ago)
Weedeater Head
Where may I find a replacement head for Weedeater 20V cordless string trimmer- mode LT 20V, serial n...
Where may I find a replacement head for Weedeater 20V cordless string trimmer- mode LT 20V, serial n...
(Posted by 622dsb 8 years ago)
How Do You Replace The Primer Bulb. There Are No Screws, Only An Assembly.
(Posted by mikewilliams1717 10 years ago)