Home » Weed Eater » Lawn & Garden » Weed Eater WE EL-15TNE

Weed Eater WE EL-15TNE Support Question

Find answers below for this question about Weed Eater WE EL-15TNE.
Need a Weed Eater WE EL-15TNE manual? We have 2 online manuals for this item!

Weed Eater Overview Questions Manuals Reviews Videos Research

Question posted by GMM203 on September 26th, 2017

How To Remove And Change Out Cutter Head On We El- 15tne

How To Remove The String Head And Replace On Trimmer

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Weed Eater WE EL-15TNE Manual Pages

Owner Manual - Page 2

...shock. • Use a voltage supply as suitable for line trimmer use multiple cords. 2 The lower the gauge number, the... the risk of electrical shock, use and replace if damaged. Do not change the equipment plug, extension cord receptacle, or...sandals. • Secure hair above shoulder length. Secure or remove loose clothing and jewelry or clothing with no cracks or deterioration...

Owner Manual - Page 3

... 0.065 inch (1.65 mm) diameter recommended trimmer line (see ATTACH THE EXTENSION CORD TO YOUR TRIMMER in cutting head. • Do not overreach or stand on and off properly. Never carry the unit by an authorized service dealer to recommended procedures. Remove objects (rocks, broken glass, nails, wire, string, etc.) which it was designed. •...

Owner Manual - Page 4

...the tubes do not come apart, repeat step 1 and push until they are secure. Remove knob and bolt from the risk of thrown objects to the unit. close excess wires in.... NOTE: Edge guide must be positioned on shield prior to the proper length while running. Remove the wire protector from the tubes and discard. 2. Assist handle Alignment Triangle 3. erly installed....

Owner Manual - Page 5

...Cord Retainer Clamp Recessed Plug Locking Sleeve Assembly Air Vents Debris Shield Edge Guide Trimmer Head with the hole in the KNOW YOUR UNIT section of the various controls and... an edging position. Insert the shield onto the motor housing. Line Limiter Blade TRIMMER HEAD The TRIMMER HEAD holds the cutting line and rotates during edging. 5 Compare the illustrations with your...

Owner Manual - Page 6

...is fed out, remove the spool cap and click spool counterclockwise until the line reaches the line limiter. Cord Retainer Extension Cord CORRECT OPERATING POSITION ADJUSTING TRIMMER HEIGHT The height of... will need to be cut . ATTACH THE EXTENSION CORD TO YOUR TRIMMER Loop your unit. Without bending over the trimmer head. Never lean over , keep line near and parallel to ensure debris...

Owner Manual - Page 7

... work area. Button EDGING While edging allow the tip of the trimmer head about 3 inches (8 cm) above the surfaces being swept and move the tool from side to the ground. Sweeping Edging 7 Take extra caution while edging as wire, string, rope, etc. WARNING: Use only 0.065 inch (1.65 mm) diameter round line. Do...

Owner Manual - Page 8

...into small hole on the inside of the arrow found on this manual. Discontinue use wire, rope, string, etc., which can break off unit with a pre--wound spool or cut out area of unit if debris.... 9. Push the line into hub with eyelet (see illustration). Remove old spool. 5. Replace with a clean dry cloth. WARNING: Never use of spool in the two cap release latches...

Owner Manual - Page 9

... against material being cut . 1. Line improperly routed in head. 2. Check line routing. 2. TROUBLE Trimmer head stops under a load or does not turn when switch is incorrect. 2. Clean unit. Line improperly routed in head. 2. Check line routing. 2. Spool worn or damaged. 1. Electrical failure. 3. Debris stopping head. Replace spool. Remove spool cap and pull 4 inches (10 cm) of...

Owner Manual - Page 10

... and/or attachments not specifically recommended by WEED EATER for repair or replacement at any time without notice or obligation to any unanswered questions concerning this warranty...workmanship and agrees to repair or replace under this product. Therefore, WEED EATER reserves the right to continuously improve its products. This warranty is to change, modify, or discontinue models, ...

Parts List - Page 1

...574492201 Description Bolt Carriage, M6 X 1 Assist Handle Knob Clamp Edge Guide Spool with 0.065" Trimmer line Shield Assembly Spool Cap Ref. Parts List No. 966048001 Date 02/26/10 NEW WEED EATER... Shown 115254226 Manual = New Part Number For This IPL = Refer to design changes. Part No. MODEL WE EL-15TNE Page: 1 2 43 1 WARNING All repairs, adjustments and maintenance not described in...