Uniden BC248CLT Support Question
Uniden BC248CLT Support Question
Find answers below for this question about Uniden BC248CLT.Need a Uniden BC248CLT manual? We have 1 online manual for this item!
Current Answers
Answer #1: Posted by waelsaidani1 on November 14th, 2017 7:33 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
Related Uniden BC248CLT Manual Pages
English Owners Manual - Page 3
TABLE OF CONTENTS
Introduction 1 About Scanning 1 Taking Proper Care of Your Scanner 2 Unpacking 2
Getting Started 3 Installing the BC248CLT 3
Operation 4 Controls and Functions 4 Scanning Overview 7
Clock Set-Up 8 Initial Clock Set-up 8
Using the Scanner 9
Set the Squelch 9
Programming Tips for Scanner 11
Programming ...
English Owners Manual - Page 4
The BC248CLT scans programmed channels at rate of up to 12 channels per second until another transmission is Scanning? When the transmission ends, the ...remains on the channel for 2 more seconds, waiting for a responding transmission. INTRODUCTION
About Scanning
Scanning Options Scanning is easy and fun with the BC248CLT 50-Channel Base Scanner with AM/FM Radio. Types of Communication below).
English Owners Manual - Page 5
...The Bearcat Radio Club and other printed information
If any known local frequencies to reset. s Do not plug the scanner into each channel you with a few sample ... Complete and mail your local library.
Monday through your Registration Form immediately. Read this list: s BC248CLT Base Scanner s Telescopic Antenna s AM Radio Antenna s AC Adapter (Model AC-144U) s This Reference...
English Owners Manual - Page 6
...electronics store.) If the optional antenna has no cable, use a 50-70 ohm coaxial cable for leadin. c. jack.
*Carefully remove the tube inserted before using the AM Antenna Jack. You may improve the reception.
4. it could cause clock reset...Adapter into the AC 10V jack on the scanner.
2. GETTING STARTED
Installing the BC248CLT
AM RADIO ANT
AC 10V
USE AC-144U ONLY EXT.SP
ANT
1. Insert ...
English Owners Manual - Page 10
Scanning Overview The BC248CLT has 50 memory channels. As the unit scans, the word SCAN moves across the display, and the bank number flashes. If no responding ...on the channel for 2 more seconds, waiting for activity (skipping channels that channel as long as the transmission continues. If you press SCAN, the BC248CLT scans each programmed frequency for a responding transmission.
English Owners Manual - Page 15
... the frequency numbers, including the decimal point, using the numeric keypad: 420.0150. Type in the display.
3. Programming Scanner Frequencies Before you can use your BC248CLT scanner, you make entry.
12
English Owners Manual - Page 17
In the event of a power failure, the scanner will retain channel information for an indefinite amount of time.
About Memory Back-up Your BC248CLT has a convenient memory back-up system. To deactivate a bank, press the bank number on the screen goes out.
.
14 Channel information is automatically in Scan ...
English Owners Manual - Page 20
... and program it into the desired channel location. The PRI indicator appears in Scan or Manual mode, press PRIORITY. To Set the Priority Channel Your BC248CLT has one default Priority Channel per bank. Press 5 and MANUAL for direct channel access.
English Owners Manual - Page 24
... for a closer station. WX icon appears in the display. To exit Weather Channel Scan mode, press SCANNER, RADIO AM/FM or OFF. Weather Channel The BC248CLT allows you to find the active weather channel in your area. Once the Weather Scan stops on a transmission, it remains on that channel.
All weather...
English Owners Manual - Page 29
... keys. Enter the time directly by pressing the w / v keys.
3. Press AM/PM to complete the entry. The display stops flashing..
26 The display digits flash.
2. Reset the Clock Time 1. Press E to select the desired setting either a.m. After the scanner has been turned on, to...
English Owners Manual - Page 34
... prevent scratches, do not use excessive amounts of water. Be careful not to reset. Contact the Uniden Customer Service Center or take it may provide better reception....the antenna. A higher elevation may be receiving a birdie. s Always write down the programmed frequencies in the electronics of the noise. Press SCAN to the unit before disconnecting the power. s Avoid placing the unit in ...
English Owners Manual - Page 35
...following steps. Check with your room. s Check to another wall outlet. TROUBLESHOOTING
If your BC248CLT is higher than 406MHz, a shorter antenna length may be using an outlet controlled by ... a fringe area.
Solution
s Check the connections at both ends of your dealer or local electronics store.
s Adjust the Squelch control.
s Move the AC Adapter to see if 50 channels...
English Owners Manual - Page 36
... none of this time. Our Uniden representatives will be happy to help you with this product, please call our Customer Hotline at this
unit, available accessories, or any other related matters.
33 s Review each channel's frequency to the threshold (Page 9). s Check the antenna connection. s Check to the threshold (Page 9). At Uniden...
English Owners Manual - Page 37
... Standard Band 470-512 MHz UHF"T" Band
Above bands in accordance with FCC Rules and Regulations Part 15 Sub-part C as of date of optional accessories are all subject to change without notice.
34 TECHNICAL SPECIFICATIONS
Certified in 12.5kHz steps 520 to 1720 KHz (AM Radio Band) 88 to 108...
English Owners Manual - Page 39
...'s manual for warranty service. PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after the date of original retail sale. The Product should include all parts and accessories originally packaged with the performance of this warranty.
This warranty is void outside the United States of original purchase and a note describing the defect that...
Similar Questions
How Can I Factory Reset My Bc248clt Where There Is No Codes In It
(Posted by jamesallenholbrook1215 1 year ago)
About My Scanner
i got a bc248clt scanner i need to program please help
i got a bc248clt scanner i need to program please help
(Posted by lavishachapman 9 years ago)
Reset To Factory
How do I do a factory reset on my bearcat bct8 scanner
How do I do a factory reset on my bearcat bct8 scanner
(Posted by codyshanks14 10 years ago)