Troy-Bilt TB625 Support Question
Troy-Bilt TB625 Support Question
Find answers below for this question about Troy-Bilt TB625.Need a Troy-Bilt TB625 manual? We have 1 online manual for this item!
Question posted by ccurrie098 on July 6th, 2019
Threading Weed Eater
how to take head off to thread weed eater
Current Answers
Answer #1: Posted by Odin on July 6th, 2019 9:37 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,640
Member since:
April 10th, 2010 Points: 41,236,640
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Troy-Bilt TB625 Manual Pages
Operation Manual - Page 1
... information available at any time without notice. Copyright© 2013 MTD SOUTHWEST INC, All Rights Reserved.
01/13 Operator's Manual
Electric Start Capable 4-Cycle Trimmer
TB625 EC
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil and Fuel 8 Starting and Stopping 10 Operation 12 Maintenance 13 Cleaning and Storage...
Operation Manual - Page 2
...; Clear the area of injury to do not by an adult.
• All guards and safety attachments must not operate the unit.
Failure to the head, hands and feet.
• Carefully inspect the area before starting the engine. Please read these instructions for the prevention of the equipment. Please keep them...
Operation Manual - Page 3
...for damage. Vibration is idling. Make sure all moving parts have stopped. 3. The cutting head remains stationary when the engine is generally an indicator of trouble. These are marked as such...short pants, sandals or go barefoot. Secure hair above shoulder level.
• The cutting head shield must be in place while operating the unit. Do not extend the trimming line ...
Operation Manual - Page 5
...Rope Grip
Primer Bulb
Fuel Cap
Handle Shaft Housing
Air Filter Cover
Throttle Control
Choke Lever
Cutting Head
Coupler
Cutting Head Shield
Oil Fill Plug
Line Cutting Blade
SPECIFICATIONS*
Engine Type Air-Cooled, 4-Cycle Displacement 30 cc... KNOW YOUR UNIT
APPLICATIONS
As a trimmer: • Cutting grass and light weeds. • Edging • Decorative trimming around trees, fences, etc.
Operation Manual - Page 6
...the location that provides the best grip. Screw the wing nut onto the square bolt until the cutting head shield is not installed. Insert the bolt into the bolt hole and push it a minimum of 6 ... with the hole on the mount bracket (Fig. 1).
4. Insert the square bolt into the slot on the cutting head shield (Fig. 1).
3. The bolt hole in . (15.24 cm)
Bolt
Fig. 3
Mount Bracket
Mount Bracket...
Operation Manual - Page 12
...be released from the operator. • Do not trim wet grass or weeds. NOTE: Do not rest the cutting head on the ground while the unit is released. This improves the unit's
cutting... unit at high speed. Keep the left hand. TIPS FOR BEST TRIMMING RESULTS • Keep the cutting head parallel to the ground. • Cut from :
• Entanglement with foreign matter • Normal line...
Operation Manual - Page 13
...Perform these procedures, take the unit to overheat or fail.
Push
the line through the cutting head until about these required maintenance procedures at 38 hours
MAINTENANCE REQUIRED
• Clean and re-oil...while the unit is complete. Always allow the unit to prevent the unit from the cutting head.
If you are of trimming line may not release properly if the line is too long...
Operation Manual - Page 14
... oil fill plug. NOTE: Make sure the O-ring is level (Fig. 20). Set the unit on the cutting head (Fig. 19). 2. Look into the holes. Adding Oil 1.
NOTE: DO NOT overfill the crankcase. 4. The... press in place on the outer
spool (Fig. 19). NOTE: Failure to prevent debris
from the cutting head. 1. Tab Hole
Fig. 19
Fig. 20
Oil Fill Plug Oil Fill Hole
Maximum Oil Level
Fig....
Operation Manual - Page 16
.... Tighten the spark plug with a 5/8-inch socket, turning it to set the air gap at a time (as follows: 1.
ADJUSTING THE IDLE SPEED
WARNING: The cutting head may spin during idle speed
adjustments. If, after checking the fuel and cleaning the air filter, the engine still will not idle • the engine...
Operation Manual - Page 18
... idle speed
Drain the fuel tank and add fresh fuel Stop the engine and clean the cutting head Clean or replace the air filter
Drain the fuel tank and add fresh fuel Clean or replace ...push the bump knob and pull the line until 4 inches (102 mm) is outside of the cutting head
THE CUTTING LINE ADVANCES UNCONTROLLABLY There is oil, cleaner or lubricant in the Starting and Stopping section
THE ENGINE...
Operation Manual - Page 20
Damage resulting from the date of any Troy-Bilt Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for a listing in the Yellow Pages, call 1-800-828-5500 or 1-800-668-1238 in Canada, ...
Similar Questions
Troy Bilt 22tb Weed Eater Trouble
Mt Troy-Bilt 2TB Weed Eater has had Bumper and Head replaced 2 times. Both were replaces because Bum...
Mt Troy-Bilt 2TB Weed Eater has had Bumper and Head replaced 2 times. Both were replaces because Bum...
(Posted by denisstpierre1961 1 year ago)
Stringing The Weed Eater
how how do you string a troy built tb22 2 cycle weedeater
how how do you string a troy built tb22 2 cycle weedeater
(Posted by Shannonslayman78 2 years ago)
Spark Plug Gap Set
what should the spark plug for. my tb625 ec troy built weed eater be gapped at?
what should the spark plug for. my tb625 ec troy built weed eater be gapped at?
(Posted by ginac566 6 years ago)
How Do I Remove The Cutting Head Of The Tb625 Ec Trimmer
head removal instructions.
head removal instructions.
(Posted by Anonymous-150877 9 years ago)
How To Change Putt Cord
How do I change the Pull Cord on my TB625ec
How do I change the Pull Cord on my TB625ec
(Posted by Christiangrill 9 years ago)