Troy-Bilt TB625 Support Question
Troy-Bilt TB625 Support Question
Find answers below for this question about Troy-Bilt TB625.Need a Troy-Bilt TB625 manual? We have 1 online manual for this item!
Question posted by Christiangrill on July 13th, 2014
How To Change Putt Cord
How do I change the Pull Cord on my TB625ec
Current Answers
Answer #1: Posted by BusterDoogen on July 13th, 2014 4:13 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,397
Member since:
October 30th, 2011 Points: 28,565,397
Go here for the procedure.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Troy-Bilt TB625 Manual Pages
Operation Manual - Page 1
...We reserve the right to obtain a list of printing. Operator's Manual
Electric Start Capable 4-Cycle Trimmer
TB625 EC
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil and...controls, operation or maintenance of the unit, please call the Customer Support Department to make changes at 1-800-828-5500 in the United States or 1-800-668-1238 in this unit,...
Operation Manual - Page 3
... in use . These parts get extremely hot from one location to another.
• If you loan this manual, should be in the starting position whenever pulling the starter rope. Inspect the unit for an adjustment.
• Adjust the handle to prevent unauthorized use them these instructions. OTHER SAFETY WARNINGS
• All...
Operation Manual - Page 5
We reserve the right to make changes at the time of printing. in.) Spark Plug Gap 0.025 in. (0.635 mm) Spark Plug Champion® RDZ4H or equivalent plug Lubrication SAE 30 Oil ...
Operation Manual - Page 7
...)
Coupler
Fig. 4
Knob
Release Button
Nut Fig. 5
Primary Hole
Guide Recess
Upper Shaft Housing
Lower Shaft Housing
Fig. 6
7 While firmly holding the upper shaft housing, pull the attachment
straight out of various optional attachments. NOTE: Do not tighten the nut (Fig. 5). Turn the knob counterclockwise to loosen (Fig. 4). 2.
CAUTION: Before operating...
Operation Manual - Page 8
... spilled. 7. Use the bottle to measure the
correct amount of maintaining the proper oil level cannot be added before each use clean oil of oil. 1. Change the oil according to Checking the Oil Level. Oil must be overemphasized. Pour the entire bottle into the oil fill hole (Fig. 8).
Reinstall the oil...
Operation Manual - Page 10
... starting position (Fig. 12). Squeeze the throttle control (Fig. 9) and pull the starter rope with a controlled and steady motion 3 to 8 times. Pull the starter rope with step 3. Move the choke lever to Position 3 (...and the unit must be in the starting the unit. Crouch in a stable position when pulling the starter rope (Fig. 12). Press and hold the throttle control, move the choke...
Operation Manual - Page 13
... to Removing Old Trimming Line and Obstructions.
2.
If necessary, remove any seasonal tune-up. Pull the line until a few inches protrude from starting accidentally.
NOTE: Maintenance, replacement, or repair...NOTE: The outer spool will remain attached to Maintaining the Air Filter.
• Change the oil.
Disconnect the spark plug wire to an MTD authorized service dealer. The ...
Operation Manual - Page 15
... out of SAE 30 oil into
a container (Fig. 22). NOTE: DO NOT overfill. Push the air filter cover back onto the air filter housing. CHANGING THE OIL
Change the oil while the engine is not covered by the product warranty. The oil will
VOID the warranty. 7. Cleaning the Air Filter
1. Wipe up...
Operation Manual - Page 16
Grasp the spark plug boot firmly and pull it from the cylinder head with a 5/8-inch socket, turning counterclockwise. NOTE: If using a torque wrench, torque to cool. Reattach the spark plug boot. NOTE: Careless ...
Operation Manual - Page 17
... in a dry, well-ventilated area. • Store the unit out of the reach of children. Pull the starter rope slowly to cool. Do not use fuel that has been stored for Use after Long... such as kerosene, can damage plastic. Refer to federal, state and local regulations.
17
Change the oil. Preparing the Unit for more than 30 days.
CLEANING AND STORAGE
CLEANING
WARNING:...
Operation Manual - Page 18
... inner reel and outer spool Open the cutting head and remove the welded section Rewind the line Stop the unit, push the bump knob and pull the line until 4 inches (102 mm) is outside of line The inner reel is bound up The cutting head is dirty The line is welded...
Operation Manual - Page 20
... has not been subject to ninety (90) days from the sales. Troy-Bilt reserves the right to change or improve the design of any Troy-Bilt Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for a listing in the Yellow Pages, call...
Similar Questions
How Do I Replace The Primer Bulb On Tb625 Ec
How do I get the cover off a Troy Bilt TB625 EC Trimmer so I can replace the Primer bulb
How do I get the cover off a Troy Bilt TB625 EC Trimmer so I can replace the Primer bulb
(Posted by Myers8708 2 years ago)
How Do I Change Cutting Head On A Troybilt Tb625ec?
I can't figure out how to remove the old cutting head.
I can't figure out how to remove the old cutting head.
(Posted by dougclapp24 7 years ago)
Troy Cs 4325 Oil Change Procedure
How do I change the oil in my chipper shredder
How do I change the oil in my chipper shredder
(Posted by gbaker1951 9 years ago)