Troy-Bilt TB625 Support Question
Troy-Bilt TB625 Support Question
Find answers below for this question about Troy-Bilt TB625.Need a Troy-Bilt TB625 manual? We have 1 online manual for this item!
Question posted by costel36 on August 24th, 2014
How Do Reinstall The Pull Clutch Unit On This Type Troy Built Unit Tb625
The person who posted this question about this Troy-Bilt product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Troy-Bilt TB625 Manual Pages
Operation Manual - Page 1
...Rights Reserved.
01/13 Operator's Manual
Electric Start Capable 4-Cycle Trimmer
TB625 EC
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil and Fuel 8 Starting and Stopping... latest product information available at any time without notice. Additional information about the unit can be performed by an authorized and approved service dealer. We reserve the...
Operation Manual - Page 2
... their explanations, deserve your LOCAL SERVICE DEALER to possible dangers.
Do not operate the unit with a spark arrestor, maintained in the Specifications section of California, Maine, Oregon and...the head, hands and feet.
• Carefully inspect the area before starting the unit. Read the operator's manual and follow these requirements could subject you are approached, stop...
Operation Manual - Page 3
... operating the unit. Be in a stable position while starting position whenever pulling the starter rope. Do not operate the unit with both ...unit faster than the maintenance procedures described in a dry place, secured or at a height to Cleaning and Storage. • Keep these instructions. Keep the engine and muffler free from debris. Use of the shield.
• This unit has a clutch...
Operation Manual - Page 4
...describes safety and international symbols and pictographs that fuel containing
greater than 10% ethanol will likely damage this unit.
Use a full face shield when needed.
• UNLEADED FUEL Always use clean, fresh unleaded fuel.... to operator's manual for the proper type of oil.
• DO NOT USE E85 FUEL IN THIS UNIT
WARNING: It has been proven that may get extremely hot from...
Operation Manual - Page 5
...Choke Lever
Cutting Head
Coupler
Cutting Head Shield
Oil Fill Plug
Line Cutting Blade
SPECIFICATIONS*
Engine Type Air-Cooled, 4-Cycle Displacement 30 cc (1.83 cu. in.) Spark Plug Gap 0.025 ...2.03 oz. (60 ml) Fuel Tank Capacity 12 oz. (355 ml) Approximate Unit Weight (No fuel, with this unit. KNOW YOUR UNIT
APPLICATIONS
As a trimmer: • Cutting grass and light weeds. • Edging...
Operation Manual - Page 6
...the square bolt until the handle is firmly in the handle should be to the type of the shaft grip (Fig. 3).
4.
Loosen the bolt with a 3/8" socket, but do not tighten the...
6.
Tighten the bolt with the hole on the cutting head shield (Fig. 1).
3. While holding the unit in the operating position (Fig. 14), move
the handle to the location that provides the best grip. Square...
Operation Manual - Page 7
...unit on the ground or on a work bench. While firmly holding the attachment, push it straight into the
coupler until the release button snaps firmly into the 90° edging hole (Fig. 4).
While firmly holding the upper shaft housing, pull... installation (Fig. 5). 3. Turn the knob counterclockwise to the unit, shut the unit off before removing or installing an attachment. Press and hold the...
Operation Manual - Page 8
...up any oil that may have spilled. 7. Reinstall the oil fill plug. Failure to the Maintenance Schedule. Check the oil level before starting the unit. Pour the entire bottle into the oil ...
Use a high-quality SAE 30 weight oil. The importance of the correct type can cause premature engine wear and failure. NOTE: This unit comes with gasoline. 6.
Unscrew the oil fill plug (Fig. 8). 5.
...
Operation Manual - Page 9
... Use a fuel additive, such as STA-BIL Fuel Stabilizer or an equivalent, to the unit's fuel tank. WARNING: Remove the fuel cap slowly to federal, state and local
regulations. WARNING: Add fuel in place. Remove the fuel cap. 3. Reinstall the fuel cap. 6.
Do not smoke while filling the tank. Alcohol-blended fuel...
Operation Manual - Page 10
... time.
the engine does not start the engine.
9.
the engine fails to Position 2, and run the unit for 2-5 minutes, or as needed . Pull the starter rope with step 3. If it does not, repeat this time. IF THE UNIT WAS RUN FOR 10-15 MINUTES AND THE ENGINE IS HOT... perform steps 3 - 8 to squeeze...
Operation Manual - Page 11
.... 10).
4. Move the choke lever to idle. 2. Allow the engine to Position 3.
Run the unit for an additional 60 seconds. Release the throttle control and allow the engine to Position 2 (Fig. ...accessory operator's manual for more information. Continue to restart the engine. The unit may be used during this instruction. Item No. Description
49M2027P966 Electric Starter ...
Operation Manual - Page 12
... Each time the bump knob is tapped, about 1.5 inches (38 mm) of injury when operating this unit.
• Stand in the cutting head shield will cut thick vegetation • Forcing the line into ...or fence posts
DECORATIVE TRIMMING When trimming around trees, posts, fences, etc., rotate the whole unit so that it easily
contacts the grass without stopping the engine. This may stall the engine...
Operation Manual - Page 13
.... Refer to overheat or fail. Refer to cool before servicing or repairing the unit. Other types of the emission control devices and system may not release properly if the line is...MTD authorized service dealer.
Installing New Trimming Line
1.
These can break off and become dangerous projectiles. Pull the line until the ends are unsure about 5 inches (12.7 cm) protrude from the exit...
Operation Manual - Page 14
... the tabs on the oil fill plug (Fig. 21). Inspecting the Oil Level Window 1. Set the unit on the outer
spool (Fig. 19). NOTE: DO NOT overfill the crankcase. 4. Check the oil level...should fill the window approximately halfway (Fig. 21). Look into the holes. Unscrew the oil fill plug. 3. Reinstall the oil fill plug.
use . If the oil level is level (Fig. 20). Adding Oil 1. Tab Hole...
Operation Manual - Page 15
... the air filter in place on the air filter
housing. Rinse the air filter
thoroughly and allow it to cool before cleaning or maintaining the unit. Reinstall the air filter in poor performance or can result in the air filter housing (Fig. 24). Insert the tab on the back of the old...
Operation Manual - Page 16
...025 in. (0.635 mm) (Fig. 26).
5. Start the engine. Grasp the spark plug boot firmly and pull it to : 110-120 in the cylinder head. NOTE: If using a torque wrench, torque to cool. ...Do not sand blast, scrape or clean spark plug
electrodes.
NOTE: Careless adjustments can seriously damage the unit. If, after checking the fuel and cleaning the air filter, the engine still will not idle &#...
Operation Manual - Page 17
... that has been stored for more than 30 days.
Reinstall the fuel cap.
2. This ensures that all of the oil from the carburetor.
3. Pull the starter rope slowly to Changing the Oil. Store the unit in a dry, well-ventilated area. • Store the unit out of the reach of any loose or damaged parts...
Operation Manual - Page 18
... the line Clean the inner reel and outer spool Open the cutting head and remove the welded section Rewind the line Stop the unit, push the bump knob and pull the line until 4 inches (102 mm) is outside of line The inner reel is bound up The cutting head is dirty The...
Operation Manual - Page 20
...Cultivator Tines, Blades. Troy-Bilt reserves the right to change or improve the design of any Troy-Bilt Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation... new merchandise purchased and used for use with respect to any Troy-Bilt product that is used in the United States, its possessions and territories. Wear items - C. No other...
Similar Questions
Fuel Tank
How do you remove the fuel tank on a troy built TB625EC leaf blower
How do you remove the fuel tank on a troy built TB625EC leaf blower
(Posted by Anonymous-172522 1 year ago)
What Are The Factory Settings On A Troy Built Tb 225 Carburetor.
What are the factory settings on a troy built TB 225 carburetor.
What are the factory settings on a troy built TB 225 carburetor.
(Posted by Cb058241 3 years ago)
Spark Plug Gap Set
what should the spark plug for. my tb625 ec troy built weed eater be gapped at?
what should the spark plug for. my tb625 ec troy built weed eater be gapped at?
(Posted by ginac566 6 years ago)
What Type Of Gas Do I Use, It Says No Mixing Oil And Gas. Same With Oil? What Ty
it says no mixing. It's a troy bilt TB625 EC WHAT GAS N WHAT OIL
it says no mixing. It's a troy bilt TB625 EC WHAT GAS N WHAT OIL
(Posted by cruzontiveros15 7 years ago)
My Troy Built Horse Tiller, Tiller Attachment Worm Gear Has Wore Out
I have a troy built tiller horse model 12056 I purchased it new the tines attachment seals have been...
I have a troy built tiller horse model 12056 I purchased it new the tines attachment seals have been...
(Posted by frankchristensen50 8 years ago)