Home » Troy-Bilt » Lawn Mowers » Troy-Bilt TB554

Troy-Bilt TB554 Support Question

Find answers below for this question about Troy-Bilt TB554.
Need a Troy-Bilt TB554 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by gls0480 on June 23rd, 2021

Can't Start Engine

new spark plug, new gas. still won't start. what else could it be?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on June 23rd, 2021 8:38 AM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,660

1,100
points

See https://www.repairclinic.com/RepairHelp/How-To-Fix-A-Lawn-Mower/79-323--/Troy-Bilt-Lawn-Mower-Won-T-Start.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Troy-Bilt TB554 Manual Pages

Operation Manual - Page 1

... MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Lawn Edger -

Operation Manual - Page 2

...troybilt.com/tutorials ◊ Call a Customer Support Representative at www.opei.org or the engine manufacturer's web site. Troy-Bilt's Customer Support telephone numbers, website address and mailing address... 15 Parts List 16 Record Product Information Before setting up , operate and maintain your new equipment, please locate the model plate on the web at www.troybilt.com See How...

Operation Manual - Page 3

... sticks, wire, bones, toys and other purpose. 4. Only responsible individuals who are recommended. Engine Exhaust, some of its entirety before attempting to operate this manual in a safe place for... blade. Keep this machine. Therefore, exercise extreme caution at least 75 feet from lawn edger while it for ordering replacement parts. 2. Never attempt to make any other foreign...

Operation Manual - Page 4

... dryer or other gas appliances. Remove gas-powered equipment from ...lawn edger off the engine and equipment. d. g. h. i. l. Contact with a portable container, rather than from your vehicle before starting . 12. Never operate without good visibility or light. Failure to the presence of ignition. Shut the engine off, disconnect the spark plug wire and ground against the engine...

Operation Manual - Page 5

Never allow children under 14 years of age to prevent unintended starting and operating the lawn edger. 8. Wrap the blade or wear gloves, and use . After striking a foreign object, stop the engine, disconnect the spark plug wire and ground against the engine to operate this machine. Improper disposal of operation. This machine is equipped with an internal...

Operation Manual - Page 7

...Set-Up 3 Contents of the handle. 7 Control Cable Z-Fitting Unwrap the control cable from the engine and route it easier to attach the Z-fitting, temporarily remove the left hand side of the brake...of the blade control. 2 Figure 3-1 2. After setting up the edger, service the engine with your machine. Assembly Handle Remove and discard any packaging cardboard that may be present between the ...

Operation Manual - Page 8

... controls inoperative. 1. Push the snap fitting down on the left side of the upper handle as shown in Figure 3-4. 2 3 1 4 Figure 3-5 Set-Up Gas & Oil Fill-Up Service the engine with gas and oil as shown in the manual bag. Press the stud found inside the snap fitting into place. Tighten the wing knob...

Operation Manual - Page 9

...in order to start the engine. It is moved, the deeper into the carburetor and aid in starting the engine. The further forward the blade depth control lever is used to start a cold engine, but do ...is used to the separate Engine Operator's Manual. It is found on the front, left portion of the edger. Be familiar with all engine controls, refer to pump gas into the soil the edger...

Operation Manual - Page 10

... until resistance is felt, then pull with your right hand, grasp recoil starter handle and pull rope slowly until engine cranks. Move the edger to an area to be difficult to start the edger's engine, proceed as follows: 1. The further forward the blade depth control lever is over concrete, asphalt, rocks or the...

Operation Manual - Page 11

...-Hand Position Left-Hand Position Figure 5-4 Section 5 - Curb Height Adjustment Lever 1 3 Trenching (If equipped) You can be edged along a curb. Disconnect the spark plug wire and ground against the engine before performing the following steps. Use two wrenches (one of five positions to ease the task of edging along . 3. See Figure 5-5. 2 Tri-Star...

Operation Manual - Page 12

Disconnect the spark plug wire and ground against the engine before performing any reason, lubricate the surface of the axle bolt and the ...end of the wheel with a light oil. Also if the wheels are removed for a detailed description of all engine-related service specifications. Refer to protect your edger for any adjustment, repairs or maintenance. Remove and discard the edger...

Operation Manual - Page 13

...1. Remove the spindle sheaves belt guard by removing the two self-tapping screws which secure it onto the engine flywheel pulley. See Figure 7-2. 5. Make certain that the "V" side of the belt is seated into ... Figure 7-1. See Figure 7-2. 4. NOTE: Make certain that the drive belt is on the engine flywheel pulley and idler pulleys, and retighten the flange lock nut on the spindle sheaves and ...

Operation Manual - Page 14

Do not store next to the Engine Operator's Manual packed separately with a light oil or silicone spray. NOTE: When ...with chassis grease to rustproof the equipment. 14 Section 7- Off-Season Storage Observe the following when preparing the edger for engine manufacturers's storage instructions. 3. Store the edger in an poorly ventilated or metal storage shed, care should be taken ...

Operation Manual - Page 15

... gasoline and refill tank with proper oil. 2. Refer to the spark plug. 6. Contact an authorized MTD service dealer. 1. Troubleshooting 8 Problem Engine fails to the Engine Operator's Manual. 1. Dirty air cleaner. 1. Blade spindle bent or damaged. 1. Refer to start Engine runs erratic Engine Overheats Occasional skips (hesitates) at high speed Idles poorly Excessive Vibration...

Operation Manual - Page 18

... for a period of export distribution. Attachments - The engine or component parts thereof. Refer to applicable manufacturer's warranty... without limitation, expenses incurred for substitute or replacement lawn care services or for terms and conditions. To...warranty. b. c. f. Replacement parts that are not limited to new merchandise purchased and used in the United States and/or its...