Home » Troy-Bilt » Lawn Mowers » Troy-Bilt TB554

Troy-Bilt TB554 Support Question

Find answers below for this question about Troy-Bilt TB554.
Need a Troy-Bilt TB554 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by Ggramkow on January 23rd, 2023

Oil & Spark Plug

How much oil needed for tb554 edger?What type spark plug does it take?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by MercedesAMG on January 23rd, 2023 12:12 PM

MercedesAMG

Member since:
January 26th, 2013

Points: 193,710

90
points

The amount of oil needed for a TB554 edger will depend on the specific model and the manufacturer's instructions. It is best to consult the owner's manual for the correct oil capacity for your specific edger.

As for the spark plug, the TB554 edger typically uses a standard small engine spark plug, such as a Champion RCJ6Y or a NGK BPMR7A. It is important to check the owner's manual or the manufacturer's website for the specific spark plug recommended for your edger model.

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!

Related Troy-Bilt TB554 Manual Pages

Operation Manual - Page 1

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Lawn Edger - Printed In USA TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Form No. 769-08749A (January 3, 2013) FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY ...

Operation Manual - Page 2

... without first contacting the Customer Support Department. Box 361131 • Cleveland, OH • 44136-0019 2 To The Owner 1 Thank You Thank you for purchasing an Edger manufactured by standing at the operator's position and looking down at the rear of the deck. We want to do NOT return the machine to...

Operation Manual - Page 3

...this machine. When you see this machine. Therefore, exercise extreme caution at least 75 feet from lawn edger while it for ordering replacement parts. 2. Do not use this manual. Use only an approved ... rough-soled work shoes and close-fitting slacks and shirts. Never attempt to make any type of power equipment, carelessness or error on the machine and be allowed to the safe ...

Operation Manual - Page 4

... accessories made for assistance or the name of your footing and keep lawn edger free of grass, leaves, or other debris build-up oil or fuel spillage and remove any fuel soaked debris. Wait 5 minutes... the machine unsafe and may run into the lawn edger. 4 Section 2 - Do not touch. 8. Shut the engine off, disconnect the spark plug wire and ground against the engine to another ...

Operation Manual - Page 5

.... 5. Thoroughly inspect the lawn edger for the muffler is required by an adult. For safety protection, frequently check all nuts, bolts, and screws tight to improper performance and compromise safety!" 10. Maintain or replace safety and instruction labels, as necessary. 12. Box 361131 Cleveland, Ohio 44136-0019. Disconnect the spark plug wire and ground...

Operation Manual - Page 7

...the hand knobs, which are located on both the left side of the edger is shipped WITHOUT GASOLINE or OIL. Assembly Handle Remove and discard any packaging cardboard that may be present between... 2. See Figure 3-2. 3. NOTE: Reference to outside. After setting up the edger, service the engine with gasoline and oil as shown in the separate Engine Operator's Manual packed with your machine. To make...

Operation Manual - Page 8

...stud found inside the snap fitting into place. Stud 1 Snap Fitting 2 2. The edger blade WILL rotate when the starter rope is hot or running. Read Instructions carefully....upper handle as shown in Figure 3-4. 2 3 1 4 Figure 3-5 Set-Up Gas & Oil Fill-Up Service the engine with gas and oil as shown in Figure 3-3. Gasoline is depressed against the upper handle. 3. Assembly & Set...

Operation Manual - Page 9

...Use it to start the engine. Blade Control Located on the front, left portion of the edger. The further forward the blade depth control lever is used to stop the machine and disengage it... the upper handle, the blade control must be depressed against the upper handle in stabilizing the edger while edging grass along a curb. Bevel Adjustment Lever The bevel adjustment lever is found on the...

Operation Manual - Page 10

... a pass. 4. With blade control lever in personal injury or property damage. Standing behind the edger, depress the blade control and hold it is over concrete, asphalt, rocks or the like. ... edged before proceeding to but not touching the edge of cut into the START position, move the edger back and forth through the cutting area, again making sure that the left hand. WARNING! To...

Operation Manual - Page 11

...to lock the wheel in order to ease the task of edging along . 3. See Figure 5-3. Edger Blade Flat Washer Flange Nut Figure 5-5 2. See Figure 5-5. 3. Use a torque wrench to tighten ...adjustment lever (refer to protect your machine and the flat washer. Operation 11 Disconnect the spark plug wire and ground against the engine before performing the following steps. To adjust the height of...

Operation Manual - Page 12

..., blade depth control lever, and if applicable, the blade adjustment lever, and curb height adjustment lever with a light oil. See Figure 6-2. Remove and discard the edger blade but retain the flange nut. 3. Disconnect the spark plug wire and ground against the engine before performing any reason, lubricate the surface of the axle bolt and...

Operation Manual - Page 13

... off of the pulleys, again making sure to Figure 7-1. Working from the front of the edger and remove the belt from around the engine flywheel pulley. WARNING! Remove the spindle sheaves belt... sheaves belt guard with the self tapping screws removed earlier. 7. Working in front of the edger, loosen the flange lock nut on top of frame, allowing the idler pulley assembly to performing...

Operation Manual - Page 14

... the edger, especially any type of power equipment in a dry, clean area. Service Coat the edger blade with the edger for long-term storage: 1. Store the edger in ...prevent rusting and corrosion. 4. Clean and lubricate the edger thoroughly as lawn fertilizer. 5. Off-Season Storage Observe the following when preparing the edger for engine manufacturers's storage instructions. 3. NOTE: ...

Operation Manual - Page 15

... dirt in gasoline tank. 5. Air flow restricted. 3. Edger blade bent or damaged. 2. Clean area around and on top of any debris. 4. Contact an authorized MTD service dealer. 1. Engine needs to the Engine Operator's Manual for gap specifications. 1. Stale fuel in fuel system. 5. Engine oil level low. 2. Spark plug fouled, faulty, or gap too wide. 2. Dirty...

Operation Manual - Page 18

... parts thereof. Service completed by any kind be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for whom it was purchased as to any warranty for loss, damage, or injury to use the product. Some states do not...