Home » Troy-Bilt » Lawn Mowers » Troy-Bilt TB554

Troy-Bilt TB554 Support Question

Find answers below for this question about Troy-Bilt TB554.
Need a Troy-Bilt TB554 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by r8rnation210 on February 22nd, 2014

Troy Bilt Tb554 Lawn Edger Wont Start Has Fuel And I Primed It...

The person who posted this question about this Troy-Bilt product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Troy-Bilt TB554 Manual Pages

Operation Manual - Page 1

Printed In USA TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Form No. 769-08749A (January 3, 2013) FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Lawn Edger - Model 554 WARNING READ AND FOLLOW...

Operation Manual - Page 2

...recommended safety practices at all models. Please be applicable to Troy-Bilt LLC • P.O. If you have any problems or questions concerning the machine, phone a authorized Troy-Bilt service dealer or contact us on this Operator's Manual ... 1 Thank You Thank you for purchasing an Edger manufactured by standing at the operator's position and looking down at the rear of the deck.

Operation Manual - Page 3

... individuals who are familiar with these rules of this machine. Therefore, exercise extreme caution at least 75 feet from lawn edger while it is to be operated according to the safe operation practices in this operator's manual carefully in bare feet...designed to perform one job: to operate this machine before attempting to edge lawn. Stop machine if anyone enters area.

Operation Manual - Page 4

... the fuel tank or container opening at too fast of a rate. 13. Allow a lawn edger to do so, can amputate hands and feet. 2. Doing so, makes the machine unsafe and may run into the lawn edger. 4 Section 2 - Failure to cool at least two minutes before starting . 18. Always be sure of your footing and keep lawn edger free...

Operation Manual - Page 5

... only, listed in effective working properly and not worn excessively. Thoroughly inspect the lawn edger for proper tightness. Improper disposal of age to prevent unintended starting and operating the lawn edger. 8. Check their proper operation regularly. 7. Repair the damage before starting . 3. Do not change the engine governor setting or overspeed the engine. Box 361131...

Operation Manual - Page 7

...it easier to attach the Z-fitting, temporarily remove the left hand side of the edger is shipped WITHOUT GASOLINE or OIL. Blade Control Upper Handle Z-Fitting 1 Figure ... 3-2. 3. Assembly & Set-Up 3 Contents of Carton • One Edger • One Engine Operator's Manual † If Equipped • One Edger Operator's Manual • One Trenching Blade Kit† • One Bottle...

Operation Manual - Page 8

...will not pull out of the engine unless the blade control (refer to avoid contact with your edger. See Figure 3-5. Assembly & Set-Up WARNING! Tighten the wing knob which secures the rope ...angle of the edger blade can be routed properly to Figure 3-4) is pulled. Using the wing knob, secure but do not tighten the rope guide to the upper handle. Never fuel the machine indoors ...

Operation Manual - Page 9

...! Recoil Starter The recoil starter is located on the upper handle, the blade control must be depressed against the upper handle in stabilizing the edger while edging grass along a curb. When placed in starting the engine. Bevel Adjustment Lever The bevel adjustment lever is used to pump gas into the soil the...

Operation Manual - Page 10

...fuel will flood the carburetor and the engine will cut into the START position, move the edger back and forth through the cutting area, again making sure to be cut . Operation 5 Starting the Engine To start . 3. Standing behind the edger... path, close to be edged, and proceed again from step 1. 10 Do not prime to bypass its operation. 1 4 3 3 2 4. This blade control mechanism is...

Operation Manual - Page 11

...the spindle sheaves and is not pinched between 37 foot-lbs. See Figure 5-4. Install the additional edger blade supplied with the flange nut removed earlier. Right-Hand Position Left-Hand Position Figure 5-4 Section...the flat washer. Edging Along a Curb The right, rear wheel of the edger can utilize the edger's optional trenching feature in relation to the height of the curb to be ...

Operation Manual - Page 12

... reason, lubricate the surface of the axle bolt and the inner surface of the wheel with your hands when working around the edger blade. 1. Edger Blade WARNING! Remove and discard the edger blade but retain the flange nut. 3. NOTE: Make certain that the drive belt is seated correctly on the blade spindle and...

Operation Manual - Page 13

... cracking, shredding or rotting are present. See Figure 7-1. 3. Discard the belt. See Figure 7-2. 6. The edger drive belt is on the engine flywheel pulley and idler pulleys, and retighten the flange lock nut on the... "V" side of the belt is seated into the top pulley and the flat side of the edger, place the belt onto the spindle sheaves, route it back onto the two idler pulleys, and...

Operation Manual - Page 14

... or metal storage shed, care should be taken to rustproof the equipment. 14 Section 7- Coat the edger, especially any type of power equipment in a dry, clean area. Refer to the Engine Operator's ... any springs and bearings with a light oil or silicone spray. Clean and lubricate the edger thoroughly as lawn fertilizer. 5. Off-Season Storage Observe the following when preparing the...

Operation Manual - Page 15

... 3. Dirty air cleaner. 1. Edger blade bent or damaged. 2. Drain fuel tank. Refer to be primed. 3. Refer to the Engine Operator's Manual 2. Stale fuel in gas cap plugged. 4. ...fuel in fuel system. 5. Dirty air cleaner. 1. Spark plug fouled, faulty, or gap too wide. 2. Remedy 1. Drain gasoline and refill tank with proper oil. 2. Refer to the spark plug. 6. Refer to start...

Operation Manual - Page 18

... be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to be defective in materials or workmanship. h. Troy-Bilt does not warrant this warranty provide the sole and exclusive remedy arising from state to you may carry a separate...