Home » Troy-Bilt » Lawn & Garden » Troy-Bilt Storm Tracker 2690

Troy-Bilt Storm Tracker 2690 Support Question

Find answers below for this question about Troy-Bilt Storm Tracker 2690.
Need a Troy-Bilt Storm Tracker 2690 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by mfitz7834 on December 15th, 2021

What Needs To Be Replaced

I love my machine..but right now it doesn't throw snow very well at all (it used to). Do I need to replace a belt? My model # is 31AM73R3766 THANKSMIKE FITZGERALD

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Deeretek on December 30th, 2021 5:21 AM

This answer was accepted by the poster of the original question.

Deeretek

Member since:
November 18th, 2021

Points: 4,410

1,100
points

Hello my name is Eric and I have been a small engine technician for 19 years and it's my pleasure to assist you today.

The problem is most likely the auger drive belt needs to be replaced.Part number is 954-04050A

Related Troy-Bilt Storm Tracker 2690 Manual Pages

Operation Manual - Page 1

... • Warranty Operator's Manual Track Drive Snow Thrower - Printed In USA TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Form No. 769-07126 (May 02, 2011) Storm Tracker 2690XP WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS...

Operation Manual - Page 2

...Failure to do NOT return the machine to right and left side of product specifications for various models. All information in this entire ...Thank You Thank you have any questions regarding the controls, operation, or maintenance of Contents Safe Operation Practices 3 Assembly & Set-Up 7 Controls 12 Operation 15 Maintenance & Adjustment 16 Service 19 Troubleshooting 23 Replacement...

Operation Manual - Page 3

... to be used. Do not wear jewelry, long scarves or other reproductive harm. Use a grounded three-wire extension cord and receptacle for ordering replacement parts. 2....Proposition 65 WARNING! Plan your snow-throwing pattern to protect your eyes. Let engine and machine adjust to outdoor temperature before starting to operate this machine without wearing adequate winter outer ...

Operation Manual - Page 4

... discharge opening at least two minutes before refueling. Replace gasoline cap and tighten securely. If gasoline is ... abnormally, stop engine before when backing up. Move machine to the disengaged position when care and good judgment...snow-throwing pattern to a complete stop before unclogging the chute assembly, making any damage before Operation 1. Never bypass its operation. Use...

Operation Manual - Page 5

... minutes to clear snow from machine and prevent freeze up of this manual. 2. Do not crank engine with the governor setting can result in effective working condition. At the end of the Average Useful Life have similar laws. Tampering with spark plug removed. 14. Maintenance & Storage 1. Refer to keep the machine in safe working...

Operation Manual - Page 6

... of inlet and discharge openings while machine is running . WARNING-GASOLINE IS FLAMMABLE Allow the engine to cool before attempting to assemble and operate. ELECTRICAL SHOCK Do not use of this product. Safety Symbols This page depicts and describes safety symbols that may pick up and throw objects which can amputate hands and...

Operation Manual - Page 7

... Support Bracket Figure 3-1 3. Secure the handle by tightening the plastic knob located on both the left and right sides of Crate • One Snow Thrower • One Snow Thrower Operator's Manual • One Engine Manual • Two Replacement Auger Shear Pins • One Chute Assembly • One Product Registration Card • One Chute Control...

Operation Manual - Page 8

... bolt Figure 3-6 previously removed but do not secure with wing nut at the one o'clock position so that the time. Rotate the joystick to the right at this 5. silver indicator arrow on the joystick and rotate the chute by hand to face forward. NOTE: The joystick will be facing up. See...

Operation Manual - Page 9

... inserting the rod with your snow thrower in the manual bag. NOTE: The hole... Refer to ensure the rod is used to line up with the hole in... 7. Figure 3-10 Set-Up Shear Pins A pair of replacement auger shear pins and bow tie cotter pins are properly routed ...Fig. 3-8. Push the chute control rod toward the control panel until needed. Check that all the way into the pinion gear below the 8....

Operation Manual - Page 10

...skid shoe is uneven, such as it can easily pick up and throw loose gravel, causing personal injury or damage to the snow thrower and surrounding property. Loosen the four hex nuts (two on... Move the skid shoes to operating the snow thrower. Retighten the nuts and bolts securely. 10 Section 2- Cut the cable tie before operating the snow thrower. Use a middle or lower position when the ...

Operation Manual - Page 11

...auger control in the operator's position (behind the snow thrower), engage the auger. 4. IMPORTANT: If the auger shows ANY signs of the machine. 6. Thread the ferrule without turning the cable ...achieved. Section 2 - Check the adjustment of motion. In a well-ventilated area, start the snow thrower engine. While standing in the disengaged "up " position, the cable should NOT be ...

Operation Manual - Page 16

... Remove the four carriage bolts and hex flange nuts which attach it to the snow thrower. 2. Refer to use the other edge. Wipe off any oil on the auger housing. Remove the ...: When lubricating the hex shaft, be checked periodically and replaced when necessary. Refer to the hex shaft. Run fuel tank dry, then carefully pivot the snow thrower up and forward so that it . Lubrication Gear ...

Operation Manual - Page 18

.... 2. Proceed as instructed earlier in it stops due to lack of the engine and the snow thrower. See Fig. 6-7. See Fig. 6-8. Thread the ferrule without turning the cable onto the... through this section. 3. Store in an unventilated area, rustproof the machine using a light oil or silicone to decrease the slack in need of the drive control as follows: 1. Retighten the hex jam nut...

Operation Manual - Page 19

Service 7 Belt Replacement 4. See Fig. 7-1. Remove the frame cover from the engine. If changing just one . Remove the key to check the condition of the snow thrower by removing the two self-tapping screws. Tip the snow thrower up and forward so that it . See Fig. 7-2. Figure 7-1 3. Figure 7-3 19 Do not attempt to pour fuel...

Operation Manual - Page 20

...Belt Figure 7-5 8. Replace auger drive belt by removing the two self-tapping screws. Fig. 7-1. 3. To remove the belt from tank by removing self-tapping screws which secure it. See Fig. 7-4. Remove the plastic belt cover on the front of the snow...snow thrower up and forward so that it stops. Ref. Roll the auger belt off engine pulley. b. Pivot the idler pulley toward the right...

Operation Manual - Page 21

... is out of wear or cracking are found. 1. Using a 3⁄4" wrench to pour fuel from the frame cover underneath the snow thrower. 4. NOTE: Engaging the drive control will ease...and 7-9. Allow the engine to the right and slide the friction wheel assembly from the shaft. Remove and replace belt in the reverse order. Figure 7-8 5. 7. Replace the friction wheel rubber if any signs...

Operation Manual - Page 22

... prior to see if the pins have sheared. If the augers will NOT be covered by your snow thrower's warranty. Remove the friction wheel rubber from the friction wheel assembly. Always turn , check to replacing shear pins. 22 Section 7 - If you only want to install the gear shaft through the assembly. NOTE...

Operation Manual - Page 23

... cable in need of auger housing with fresh fuel. 4. Shear pin(s) sheared. 3. Auger belt loose or damaged. 1. Run engine until it stops. Refer to easily rotate 180 degrees 1. Snow Thrower fails to propel itself Snow Thrower fails to discharge snow Chute fails to the Maintenance & Adjustments Section. 5. Connect and tighten spark plug wire. 2. Replace drive belt. Be...

Operation Manual - Page 24

...free of charge at www.troybilt.com. 24 Replacement Parts Component 9 Part Number and Description 929-0071A Extension Cord, 110V 954-04050 954-04260 Auger Drive Belt Wheel Drive Belt 684-04159 935-04054 Friction Wheel Assembly Friction... 951-10292 Spark Plug Phone (800) 828-5500 to order replacement parts or a complete Parts Manual (have your full model number and serial number ready).

Operation Manual - Page 26

...limitation, expenses incurred for substitute or replacement lawn care services or for a period ...: batteries, belts, blades, blade adapters, tines, grass bags, wheels, rider deck wheels, seats, snow thrower skid ... parts. Attachments include, but are warranted to use , neglect, accident, improper maintenance, alteration, ... warranty gives you specific legal rights, and you and your property...