Troy-Bilt Storm 2840 Support Question
Troy-Bilt Storm 2840 Support Question
Find answers below for this question about Troy-Bilt Storm 2840.Need a Troy-Bilt Storm 2840 manual? We have 1 online manual for this item!
Question posted by JerryFLevine on February 20th, 2021
Replace Auger Engagement Cable
How do I replace the auger engagement cable on the 2 stage Storm 2840 snow blower?
Current Answers
Answer #1: Posted by waelsaidani1 on February 20th, 2021 7:21 PM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,787
Member since:
May 12th, 2013 Points: 19,501,787
Related Troy-Bilt Storm 2840 Manual Pages
Operation Manual - Page 1
...; Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Two-Stage Snow Thrower - Printed In USA
TROY-BILT LLC, P.O.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
Storm 2410, 2620, 2840 & 3090XP
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING...
Operation Manual - Page 3
... without wearing adequate winter outer garments. Let engine and machine adjust to clear snow.
3 Never allow adults to the safe operation practices in serious injury or ... not followed,
could be trained and supervised by the auger/impeller.
1. Use a grounded three-wire extension cord and receptacle for ordering replacement parts.
2. Never attempt to avoid discharge of yourself...
Operation Manual - Page 4
...situations occur which can cause a burn.
Important Safe Operation Practices Wash your snow-throwing pattern to the disengaged position when
care and good judgment.
Plan your ... manufacturer (e.g. Replace gasoline cap and tighten securely. If gasoline is felt, then pull rapidly. i.
slippery surfaces. Allow machine to the auger/impeller when transporting...
Operation Manual - Page 5
...performance and compromise safety!"
6. Wait until the auger/impeller come to clear snow from machine and prevent freeze up of the engine.
5. Maintain or replace safety and instruction labels, as a water heater,...available through your hand to operate on off-season storage.
12. to verify they engage and disengage properly and adjust, if necessary. Clearing a Clogged Discharge Chute
Hand ...
Operation Manual - Page 7
... the left and right sides of Carton
• One Snow Thrower • One Snow Thrower Operator's
Manual • One Engine Manual
• Two Replacement Auger Shear Pins • One Chute Assembly (Model 2410)
• One Product Registration Card
• One Chute Control Rod (Models 2620, 2840 and 3090XP)
Assembly
Handle
1. See Fig. 3-1. See Fig. 3-3. Remove...
Operation Manual - Page 10
...auger housing with the hole in your snow thrower.
Cut the cable tie before operating the snow thrower. Push the chute control rod toward the control panel until needed. Store them in the chute control input closest to achieve further engagement... pin. cable guide on top of replacement auger shear pins and bow tie cotter pins are properly routed through the cable guide....
Operation Manual - Page 12
... more slack (or downward to the front of rotating, immediately return to operating your snow thrower is released and in the operator's position (behind the snow thrower), engage the auger.
4. While standing in the disengaged "up " position, walk to increase cable tension).
9.
Repeat steps 2 through 6 above to Engine Operator's Manual.
3. It should have very little...
Operation Manual - Page 13
... equipped)
The headlight is located on when the engine is started.
13 Shift Lever
The shift lever is located in Fig. 4-1. Augers
When engaged, the augers rotate and draw snow into the auger housing is automatically turned on top of travel. Chute assembly styles and appearance vary by model. One (1) is the slower and two...
Operation Manual - Page 14
... machine's drive system.
Squeeze the control grip against the handle to stop . Release to engage the augers and start snow throwing action. Squeeze the control grip against the handle to stop the augers and wheel drive. Release both controls to engage the wheel drive. Heated Grips (if so equipped)
Caution: It is located on the...
Operation Manual - Page 15
... control to turn left . • To change the angle/distance which snow is conveniently fastened to the rear of the auger housing with these controls.
Shut off engine and remain behind the snow thrower), engage the auger control for a few seconds to clear any snow and ice which has formed in and near the chute assembly...
Operation Manual - Page 16
... into one of failing to see if the pins have sheared. To Engage Augers
To engage the augers and start throwing snow, squeeze the auger control against the handle the snow thrower will not turn, check to do so will stop the augers. Replacing Shear Pins
The augers are secured to turn it and drive motion will NOT be covered...
Operation Manual - Page 17
...) to the inside of fuel.
2. When one side wears out, they can be checked periodically and replaced when necessary. Remove the four carriage bolts and hex flange nuts which attach it to run until it... off any oil on each side) and hex flange nuts. Allow the engine to
the auger housing. 2. Carefully pivot the snow thrower up and forward so that it . NOTE: When lubricating the hex shaft, be ...
Operation Manual - Page 18
... manual.
2. With the drive control released, push the snow thrower gently forward.
Shut off the engine as instructed in the shift lever. Check the adjustment of adjustment.
Engage the drive control and gently attempt to increase cable tension).
4. There should have very little slack.
Auger Control
Refer to verify proper adjustment has been achieved...
Operation Manual - Page 19
...engaging with the second hole in the chute rotation assembly. See Fig. 6-7.
Figure 6-7
2. Clean the exterior of the chute directional control is empty and it stops due
to lack of fuel.
Chute Control Rod (Models 2620, 2840...cotter pin through this section. 3.
See Fig. 6-6. Off-Season Storage
If the snow thrower will not be adjusted. Loosen the two nuts which secure the chute bracket ...
Operation Manual - Page 20
... removing the self-tapping screws which acts as follows:
4. See Fig. 7-1.
Unhook the auger brake bracket spring from the underside of the snow thrower by removing the two self-tapping screws. Service
7
Belt Replacement
Auger Belt
To remove and replace your snow thrower's auger belt, proceed as a belt keeper. Remove the key to pour fuel from the...
Operation Manual - Page 21
...:
1.
Refer to the frame after installing a replacement auger belt.
9. 7.
Service
21 To prevent spillage, remove all fuel from the engine.
2.
b. Remove the frame cover from around the auger pulley, and slip the Drive Belt
belt between the support bracket and the auger pulley. To remove and replace your snow thrower's drive belt, proceed as follows (See...
Operation Manual - Page 22
... fails to drive with the drive control engaged, and performing the drive control cable adjustment fails to correct the problem, the friction wheel may need to replace the snow thrower's friction wheel rubber. Carefully pivot the snow thrower up and forward so that it rests on the auger housing.
3.
To inspect the friction wheel, proceed as...
Operation Manual - Page 24
... or a stick.
3. Move choke lever to Service section.
1. Contact an authorized Service Center. 5. Remove ice and snow from auger with clean, fresh gasoline. 4. Friction wheel worn. 1. Foreign object lodged in fuel system. 4. Adjust drive control cable. Replace drive belt. Engine not primed.
5. Carburetor not adjusted properly. 1. Spark plug wire loose. 2. Insert key fully into...
Operation Manual - Page 25
...
Replacement Parts
Component
9
Part Number and Description
929-0071A
Extension Cord, 110V
954-04050 954-04195 954-04260 954-04201A
684-04153 684-04159 935-04054
Auger Drive Belt (Storm 2410 & Storm 2620 with 15" tires) Auger Drive Belt (Storm 2840 & 3090XP & Storm 2620 with 16" tires) Wheel Drive Belt (Storm 2410 & Storm 2620 with 15" tires) Wheel Drive Belt (Storm 2840...
Operation Manual - Page 28
... or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to use or exposure. Check your Yellow Pages... adapters, tines, grass bags, wheels, rider deck wheels, seats, snow thrower skid shoes, friction wheels, shave plates, auger spiral rubber and tires.
HOW STATE LAW RELATES TO THIS WARRANTY:...
Similar Questions
I Need To Rotate My Auger Manually To Access The Sheer Pins That Have Broken Fro
(Posted by Rlmazz 2 years ago)
Auger Will Not Rotate When Depressing Handle.
After starting the blower, I depress the handle to engage the auger and smoke along with a burning r...
After starting the blower, I depress the handle to engage the auger and smoke along with a burning r...
(Posted by ldavidson1 3 years ago)
Troy-bilt 31ah64q4711 (2012) Storm 2840 Snowblower Runs Rough & Gas Leak @ Carb
I have a Troy-Bilt 31AH64Q4711 (2012) Storm 2840 Snowblower gas leak @ carb. Removed carb, cleaned t...
I have a Troy-Bilt 31AH64Q4711 (2012) Storm 2840 Snowblower gas leak @ carb. Removed carb, cleaned t...
(Posted by Nborho 6 years ago)
We Are Finding It Impossible To Attach The Chute To The Snow Blower,storm 2410
The chute on our snow blower keeps coming off when clearing snow. It looks like the plastic pieces a...
The chute on our snow blower keeps coming off when clearing snow. It looks like the plastic pieces a...
(Posted by wfingerman 8 years ago)
Troy-bilt Storm 2620 Snow Thrower Is Blowing Oil
What can I do to stop my barely-used Troy-Bilt Snow Thrower from blowing oil out of the oil stick tu...
What can I do to stop my barely-used Troy-Bilt Snow Thrower from blowing oil out of the oil stick tu...
(Posted by cnchunter 8 years ago)