Home » Troy-Bilt » Lawn & Garden » Troy-Bilt Storm 2620

Troy-Bilt Storm 2620 Support Question

Find answers below for this question about Troy-Bilt Storm 2620.
Need a Troy-Bilt Storm 2620 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by cnchunter on October 21st, 2015

Troy-bilt Storm 2620 Snow Thrower Is Blowing Oil

What can I do to stop my barely-used Troy-Bilt Snow Thrower from blowing oil out of the oil stick tube and air blower? It was hard to start after leaving it sitting for three years with old gasoline. It started ok after adding gas treatment but it blows oil and also leaks gas from the primer.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by JVA1979 on February 9th, 2016 2:59 PM

JVA1979

Member since:
February 9th, 2016

Points: 0

100
points

id gas is leaking from the primer and it's sat for a extended period of time then check the oil , if it has a gas smell or its thin the problem is the carburetor . The needle is not seating with the inlet valve so when the float closes the needle is allowing gas to bypass it being why the oil is coming out the breather tube etc as it thins . If it's continued to run like this it will destroy the motor , to fix it the carburetor has to be removed and cleaned or rebuilt replacing the needle etc . While the carburetor is off change the oil as the gas oil mix is bad and will lock the motor up . If you rebuild the carburetor to test it flip it upside down and try to blow in the part the fuel line goes to . If you can blow in it at all w I th the float closed it's still leaking .

Related Troy-Bilt Storm 2620 Manual Pages

Operation Manual - Page 1

Printed In USA TROY-BILT LLC, P.O. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. BOX 361131 CLEVELAND, OHIO 44136-0019 Form No. 769-06897 (May 17, 2011) Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Two-Stage Snow Thrower - Storm 2410, 2620, 2840 & 3090XP...

Operation Manual - Page 2

...provided area to safely and easily set up and operating your machine, for purchasing a Troy-Bilt Snow Thrower. We reserve the right to all times. Review this product or have any other ...the Customer Support Department. Table of printing. Failure to do NOT return the machine to Troy-Bilt LLC • P.O. Please read this manual is responsible for various models. You can ...

Operation Manual - Page 5

... ground against the engine to be sure the impeller blades have stopped rotating. 3. Snow thrower shave plates and skid shoes are working properly and not worn excessively. For your hand to the adjustment section in this product has an Average Useful Life of seven (7) years, or 60 hours of California the above is available through...

Operation Manual - Page 7

... both the left and right sides of Carton • One Snow Thrower • One Snow Thrower Operator's Manual • One Engine Manual • Two Replacement Auger Shear Pins • One Chute Assembly (Model 2410) • One Product Registration Card • One Chute Control Rod (Models 2620, 2840 and 3090XP) Assembly Handle 1. Place the shift lever...

Operation Manual - Page 10

...-Up Figure 3-15 Store them in your snow thrower. Some models only have one cable to route through the Chute Clean-Out Tool The chute clean-out tool is used to the left of the engine. See ... with the hole in step 1. See Fig. 3-3. 9. Check that the cables are included with your snow thrower's dash panel until the hole in the rod lines up with a mounting clip and a cable tie...

Operation Manual - Page 11

... and 2620) NOTE: The upper chute on the skid shoes. 3. Insert Key into engine and start engine. Move skid shoes to the Engine Operator's Manual. Remove the key from the engine and loosen the plastic knob found on each side) and carriage bolts. Refer to operate the snow thrower on the auger housing. • Use...

Operation Manual - Page 12

... the auger shows ANY signs of the auger control as follows: 1. Repeat steps 2 through 6 above to stop before releasing the auger control. Prior to operating your snow thrower is released and in the operator's position (behind the snow thrower), engage the auger. 4. See Fig. 3-18. Allow the auger to remain engaged for ALL moving parts...

Operation Manual - Page 13

...8224; Augers Skid Shoe † If Equipped Figure 4-1 Snow thrower controls and features are two reverse (R) speeds. Position ...used to determine ground speed and direction of the handle panel and is discharged out the chute assembly. Adjust upward for hard-packed snow. Chute Assembly Snow... engine is started. 13 Augers When engaged, the augers rotate and draw snow into the ...

Operation Manual - Page 14

... joy-stick to the right or to the left side of the dash panel to stop the augers and wheel drive. Drive Control / Auger Clutch Lock The chute directional control is thrown, squeeze the button on the rear of the snow thrower. Squeeze the control grip against the handle to engage the augers and start snow...

Operation Manual - Page 15

... the snow thrower in the operator's position (behind handles until you are located on the underside of the handles. • Squeeze the right control to turn right. • Squeeze the left control to turn left . • To change the angle/distance which snow is thrown, pivot the joy-stick forward or backward. Never use your...

Operation Manual - Page 16

... start throwing snow, squeeze the auger control against the handle the snow thrower will NOT be covered by your snow thrower for the snow conditions and a pace you wear gloves when using ... that you 're comfortable with. 2. Operation 5 Starting and Stopping the Engine Refer to the Engine Operator's Manual packed with your snow thrower's warranty. Squeeze the drive control against the left ...

Operation Manual - Page 17

...skid shoes (on each side) and hex flange nuts. Doing so will hinder the snow thrower's drive system. Remove the four carriage bolts and hex flange nuts which secure it...3-in -1 oil) to get any excess or spilled oil. Maintenance & Adjustments 6 Maintenance Engine Refer to Fig 7-3. 4. Refer to use the other edge. To remove skid shoes: 1. Carefully pivot the snow thrower up and forward...

Operation Manual - Page 18

... is released and in the shift lever. With the drive control released, push the snow thrower gently forward. With the drive control released, move the shift lever back and forth ...the drive cable bracket. Position the bracket upward to provide more slack (or downward to push the snow thrower forward. It should not roll freely. 3. There should have very little slack. Place the shift...

Operation Manual - Page 19

...2620, 2840, y 3090XP) To adjust the chute control rod, proceed as instructed earlier in this hole and the chute control rod. Remove the cotter pin from the engine. 2. Retighten the nuts. Off-Season Storage If the snow thrower... and reposition it stops due to lack of the engine and the snow thrower. See Fig. ...the machine using a light oil or silicone to coat the snow thrower. 5. Chute...

Operation Manual - Page 20

... belt as follows: 4. Service 7 Belt Replacement Auger Belt To remove and replace your snow thrower's auger belt, proceed as follows. Figure 7-2 20 Figure 7-4 b. Roll the auger belt ...tapping screws which acts as a belt keeper. Do not attempt to avoid unintended starting. 2. Carefully pivot the snow thrower up and forward so that it . See Fig. 7-3. 1. Figure 7-1 3....

Operation Manual - Page 21

... by running engine until it stops. Replace the auger belt by removing the self-tapping screws which secure it rests on the front of the snow thrower by following instructions in reverse ...installing a replacement auger belt. 9. Figure 7-6 a. Service 21 See Fig. 7-5. Carefully pivot the snow thrower up and forward so that it . Remove the frame cover from tank by removing the two ...

Operation Manual - Page 22

... of the belt. Place the shift lever in the reverse order. Do not attempt to replace the snow thrower's friction wheel rubber. 6. Back out the stop bolt. Stop Bolt Friction Wheel Removal (Models 2410, 2620 & 2840) If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjustment fails to...

Operation Manual - Page 23

... (between the plates. 3. Slide the friction wheel assembly back onto the hex shaft and follow the steps above in reverse order to reassemble to the snow thrower frame and lightly tap the shaft's end to the left before turning the wheel clockwise and proceeding with a new rubber ring. Figure 7-10 Section 7 - Remove...

Operation Manual - Page 26

...-679 490-241-0010 OEM-390-995 490-241-Y014 *Not compatible with Storm 2410. Phone (800) 828-5500 for your full model number and serial number ready). Heated Grips* Drift Cutter Kit Polymer Skid Shoe Kit Snow Thrower Protective Cover Troy-Bilt Snow Thrower Maintenance Kit 26 Attachments & Accessories 10 The following attachments and accessories are...

Operation Manual - Page 28

...belts, blades, blade adapters, tines, grass bags, wheels, rider deck wheels, seats, snow thrower skid shoes, friction wheels, shave plates, auger spiral rubber and tires. Alteration of safety ...years commencing on to items such as described below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in accordance with the Operator's Manual furnished with respect to use...