Troy-Bilt CSV 206 Support Question
Troy-Bilt CSV 206 Support Question
Find answers below for this question about Troy-Bilt CSV 206.Need a Troy-Bilt CSV 206 manual? We have 1 online manual for this item!
Question posted by sensualmass on October 25th, 2014
Starting The Machine
I have tried to start my machine, after sitting idle from last winter... Can not start it. Removed all the old gas and still nothing... do you have any suggestions. Sincerely Reginald
Current Answers
Answer #1: Posted by freginold on November 16th, 2014 6:01 AM
freginold
Member since:
December 20th, 2011 Points: 23,253,885
Member since:
December 20th, 2011 Points: 23,253,885
There are many things that could be causing the problem. Try spraying some starting fluid into the carburetor (with the air filter removed and the machine off) then put the filter back on and try starting it up -- if it starts and then dies, there is probably a blockage in the carb or fuel line. It could also be the air filter causing the problem -- if it's dirty, you can either clean or repace it.
If it won't start, even for a moment, after you spray the starting fluid, then you may have a problem with your spark plug. You could either try cleaning and regapping it, or replacing it.
If it still won't start, attach a spark plug tester to your spark plug to see if the plug is getting electricity. If it's not, there's a problem before the spark plug, with one of the internal electrical components.
If it won't start, even for a moment, after you spray the starting fluid, then you may have a problem with your spark plug. You could either try cleaning and regapping it, or replacing it.
If it still won't start, attach a spark plug tester to your spark plug to see if the plug is getting electricity. If it's not, there's a problem before the spark plug, with one of the internal electrical components.
Related Troy-Bilt CSV 206 Manual Pages
Operation Manual - Page 1
... • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Chipper Shredder Vacuum Model CSV 206
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. BOX 361131 CLEVELAND, OHIO 44136-0019
Form No. 769-06181 (June 9, 2010)
Printed In USA
TROY-BILT...
Operation Manual - Page 2
...all models. Throughout this manual, all references to all engine-related issues with the machine, its features and operation.
Choose from the experts.
Please refer to operating the...Replacement Parts 16 Warranty 20
Record Product Information
Before setting up , operate and maintain your machine, for more information. You can seek help from the options below: ◊ Visit ...
Operation Manual - Page 3
...odorless and deadly gas.
7. Contact with any damage at least 75 feet from the machine while it ...starting, check all moving parts have come to a complete stop the machine and disengage them quickly.
3. This machine is to operate this symbol -
Keep this manual in this machine...intake or discharge opening, remove or empty bag, or inspect and repair the machine while the engine is in...
Operation Manual - Page 4
Wash your machine should start making an unusual noise or vibration, immediately shut the engine off. c. When practical, remove gas-powered equipment from the truck or trailer and refuel it off , wait until fueling is running.
Do
specified on the ground. Personal injury or machine damage could cause personal injury or damage to the
machine.
4
Section 2 - Extinguish...
Operation Manual - Page 5
...there is required by an authorized service dealer to keep the machine in any damage and repair, if needed.
3. to prevent unintended starting.
4. Failure to be maintained in accidents, injuries or death...Average Useful Life have similar laws. If the fuel tank has to do this manual for gas, oil, etc. If a spark arrester is equipped with California and federal EPA emission regulations...
Operation Manual - Page 6
... engine indoors or in operation.
SAVE THESE INSTRUCTIONS!
6
Section 2 - Engine exhaust contains carbon monoxide, an odorless and deadly gas. WARNING- warning: Your Responsibility-Restrict the use of inlet and discharge openings while machine is in a poorly ventilated area. WARNING- Important Safe Operation Practices
GASOLINE IS FLAMMABLE Allow the engine to assemble and...
Operation Manual - Page 7
...studs on the nozzle must depress the safety switch button attached to the right side of the lower handle. Chipper Chute
1. Remove three wing nuts from the front of Carton
• One Chipper Shredder Vacuum • One Chipper Chute • One Bag... Operator's Manual • One Safety Glasses • One Bottle of the chipper shredder vacuum or engine will not start. A B
Figure 3-3 7
Operation Manual - Page 8
... this point in Fig. 3-5A. See
Fig. 3-5B.
5. See Fig. 3-4B. the three hex nuts and bell washers that were removed
earlier. Release the clamp. See Fig. 3-6. See Fig. 3-4D.
8
Section 3 - A B
B, C, & D
A & D...bag over the upper handle, hooking them on the drawstring and pull the
just removed. Loosely secure with
direction of the bag over the discharge chute, making
4. ...
Operation Manual - Page 9
... adjusted to one of ignition. Add oil provided before starting unit for adjusting the nozzle door upwards or downwards....-Up
9 Release lever towards nozzle. Figure 3-8
2. Set-Up
Gas and Oil Fill-Up
Refer to provide best performance.
1. Adjustments
Nozzle... of five positions, ranging from nozzle.
2. Never fuel the machine indoors or while the engine is extremely flammable and the vapors...
Operation Manual - Page 10
.... Vacuum/Chipper Bag
Collects shredded or chipped material fed through the chipper chute or vacuumed up to 3" in diameter to slow down or stop the machine and disengage them quickly.
Nozzle Door Adjustment Levers
The nozzle adjustment levers are located on the upper handle assembly. Caster Locks
The caster locks are...
Operation Manual - Page 11
... other than specified on the left rear wheel to the machine. 1.
If the flail screen becomes clogged, remove and clean as instructed in this machine unless the discharge chute and bag have been properly installed and secured to prevent the unit from the machine before starting .
6. Attach spark plug wire to STOP or OFF position...
Operation Manual - Page 12
...
• Wash bag periodically with a forceful spray of the swivel pins. Stop the engine. Remove the four self-tapping screws from warranty, operator must maintain the equipment as instructed here.
•...cleaner, refer to the separate engine manual packed with your machine. Disconnect spark plug wire from the
top and remove the discharge chute assembly. See Fig. 6-1A. Lubricate each...
Operation Manual - Page 13
...with the drive control disengaged.
• It does not self-propel with the hardware previously removed and attach the bag to reassemble the flail screen with the lever further away from inside... above situation is 30 psi. Lift the flail screen from the handle, tighten the cable. Remove the two hex bolts and hex nuts which the drive control is slipping (unit hesitates while engine...
Operation Manual - Page 14
Remove other gas appliance.
14 Also, make sure to remove an equal amount from each blade and torque hardware to change the ...equipment is an open flame, spark, or pilot light such as on the machine, wait for correct engine storage instructions.
• Store equipment in a clean, dry area.
See Fig. 7-1A.
6. Remove the chipper blade using a 3/16" allen wrench and a 1/2" wrench....
Operation Manual - Page 15
... lever not in fuel system. 6. Water or dirt in correct starting position.
2. Dirty air cleaner. 1. Carburetor idle mixture adjustment
improperly set. 1. Drive belt worn or damaged.
1....if equipped). 4. Chipper blade dull.
1. Remove spark plug and adjust gap to engine manual.
1. Drain fuel tank. Vacuum bag is engaged
1. Remove lodged object.
3. Stop engine and disconnect ...
Operation Manual - Page 20
... warranty for rental expenses to any kind be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for products sold through your local authorized service dealer.
Normal wear parts include, but are not limited to our Web site at...
Similar Questions
I Have A Troy Bilt Lawn Tractor That Won't Start.
I've narrowed it down to the shifter ,forward, neutral, reverse mechcanism, when i wiggle it cranks ...
I've narrowed it down to the shifter ,forward, neutral, reverse mechcanism, when i wiggle it cranks ...
(Posted by carptr50 6 years ago)
Troy-bilt Storm 2620 Snow Thrower Is Blowing Oil
What can I do to stop my barely-used Troy-Bilt Snow Thrower from blowing oil out of the oil stick tu...
What can I do to stop my barely-used Troy-Bilt Snow Thrower from blowing oil out of the oil stick tu...
(Posted by cnchunter 8 years ago)
Troy Bilt 2cycle Weedeater
Bought brand new last yr. Used twice. If u can get it to run it gets hot and stops after five minute...
Bought brand new last yr. Used twice. If u can get it to run it gets hot and stops after five minute...
(Posted by onelitlarkie 9 years ago)
Is There A Secret To Restart This Pos After You Stop It To Empty The Bag?
I bought this used. I had to have it tuned up after I replaced the plug and filter. It ran well, one...
I bought this used. I had to have it tuned up after I replaced the plug and filter. It ran well, one...
(Posted by billcal3 9 years ago)