Home » TP-Link » Hubs & Switches » TP-Link TL-SG5426

TP-Link TL-SG5426 Support Question

Find answers below for this question about TP-Link TL-SG5426.
Need a TP-Link TL-SG5426 manual? We have 1 online manual for this item!

TP-Link Overview Questions Manuals Reviews Videos Research

Question posted by oscarh on January 25th, 2012

How Do I Get Connected To The Tp-link Tl-sg5426 Via Telnet?

I don't have the RS232 cable, therefore I need connected by telnet, and then i need configure switch's IP because I don't know the IP by default. When I get the IP, then I will conected by WEB Interface.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by mixalot111 on April 22nd, 2014 3:21 PM

mixalot111

Member since:
April 22nd, 2014

Points: 0

100
points

The default IP address for TP-LINK TL-SG5426 switch is 192.168.0.1, so set your computer/laptop's address to (example) 192.168.0.100 and then in your browser just open http://192.168.0.1/

Related TP-Link TL-SG5426 Manual Pages

User Guide - Page 34

...see "Setting an IP Address" on the switch, or remotely by default. The switch's web management interface can be managed from any port by a direct connection to the RS-232 serial console port on page 2-4. The switch's management agent also supports SNMP (Simple Network Management Protocol). Chapter 2: Initial Configuration Connecting to the Switch Configuration Options The switch includes...

User Guide - Page 36

... program can also be accessed using Telnet from any computer using a console connection, DHCP or BOOTP protocol. normal access level (Normal Exec) and privileged access level (Privileged Exec). To fully configure the switch parameters, you must first configure it with a valid IP address, subnet mask, and default gateway using a web browser (Internet Explorer 5.0 or above, or Netscape...

User Guide - Page 37

... password. Type "username admin password 0 password," for this switch is obtained via DHCP by default. 2-4 You have to BOOTP or DHCP address allocation servers on another network segment. Open the console interface with the TL-SG5426 is opened. To end the CLI session, enter [Exit]. Manual Configuration You can consist of four decimal numbers, 0 to the...

User Guide - Page 43

... time to the console port or via Telnet. See "Configuring Interface Settings" on the network using an out-of -band serial connection. on page 2-4.) 3. Note: You can set the switch port attached to your management station and this switch does not pass through the web interface. Prior to accessing the switch from a web browser, be accessed by the same user...

User Guide - Page 47

...-Key Settings Port Security 802.1X Information Configuration Port Configuration Statistics ACL Configuration Port Binding IP Filter Port Port Information Trunk Information Port Configuration Trunk Configuration Trunk Membership LACP Configuration 3 Navigating the Web Browser Interface Table 3-2 Main Menu (Continued) Description Sets the SNMP v3 engine ID on this switch Sets the SNMP v3 engine ID...

User Guide - Page 52

... the system. • System Up Time - Shows the TCP port number used by the Telnet interface. • Jumbo Frame - Length of the power-on self-test. 3 Configuring the Switch Basic Configuration Displaying System Information You can easily identify the system by the web interface. • Web secure server - Field Attributes • System Name - Shows if management access via...

User Guide - Page 117

... Usage • The management interfaces are allowed management access to all IP addresses by default. Once you add an entry to a filter list, access to that are open to the switch through the web interface, SNMP, or Telnet. 3 Configuring the Switch Figure 3-47 Configuring ACL Port Binding CLI - Console(config)#interface ethernet 1/1 Console(config-if)#ip access-group david in Console...

User Guide - Page 123

... negotiate a trunk link between devices, use the web interface or CLI to eight ports per trunk. • The ports at both ends of a connection must comply with LACP-configured ports on a switch, with the Cisco EtherChannel standard. 3-80 However, before you connect the corresponding network cables between two devices. 3 Configuring the Switch CLI - Select the interface, and then enter...

User Guide - Page 127

...interfaces that joined the group (lacp admin key, as the port admin key used to determine link aggregation group (LAG) membership, and to identify this switch. • Port - Command Attributes Set Port Actor - This menu sets the local side of 0), this section and on 4-134). Default: 32768) - 3 Configuring the Switch... null value of an aggregate link; Just connect these ports to join the ...

User Guide - Page 145

...All ports connected to 300 seconds. 3 Configuring the Switch Changing the Aging Time You can be used to detect and disable network loops, and to provide backup links between any ...Default: 300 seconds) Web - Click Address Table, Address Aging. Specify the new aging time, click Apply. Console(config)#mac-address-table aging-time 300 Console(config)# 4-142 Spanning Tree Algorithm Configuration...

User Guide - Page 158

.... (Default: Disabled) Web - A connection to -Point - Click Spanning Tree, STA, Port Configuration or Trunk Configuration. Console(config)#interface ethernet 1/7 Console(config-if)#spanning-tree port-priority 0 Console(config-if)#spanning-tree cost 50 Console(config-if)#spanning-tree link-type auto Console(config-if)#no spanning-tree edge-port Console(config-if)# 4-116 4-155 4-154 4-157...

User Guide - Page 175

... independent BPDU frames, such as GMRP. • Mode - 3 Configuring the Switch Configuring VLAN Behavior for Interfaces You can be configured as an untagged member. When set to receive all other VLANs, the PVID must be discarded. - Ingress filtering only affects tagged frames. - VLAN ID assigned to the default VLAN. (Options: All, Tagged; Specifies a port as tagged...

User Guide - Page 237

...manages Member switches using cluster "internal" IP addresses. There can use both the web interface and Telnet to 16 Member switches in the cluster. Figure 3-121 Dynamic IP Source Guard Binding Information CLI - The management station can be grouped together regardless of grouping switches together to within a single IP subnet. 3-194 This example shows how to configure a static source...

User Guide - Page 265

... Command Group Device Designation User Access IP Filter Web Server Telnet Server Secure Shell Event Logging Time (System Clock) System Status Frame Size Table 4-7 System Management Commands Function Page Configures information that uniquely identifies this switch 4-24 Configures the basic user names and passwords for management access 4-25 Configures IP addresses that are used in PE...

User Guide - Page 269

... individual addresses or address ranges. • When entering addresses for SNMP, web and Telnet access respectively. You must delete the entire range, and reenter the addresses. • You can be configured for the same group (i.e., SNMP, web or Telnet), the switch will reject the connection, enter an event message in the system log, and send a trap message...

User Guide - Page 273

... Commands Command ip telnet port ip telnet server Table 4-14 Telnet Server Commands Function Mode Page Specifies the port to be used by the Telnet interface GC 4-29 Allows the switch to be used by the browser interface. (Range: 1-65535) Default Setting 23 Command Mode Global Configuration Example Console(config)#ip telnet port 123 Console(config)# Related Commands ip telnet server (4-33...

User Guide - Page 360

...negotiation is disabled, you must manually specify the link attributes with the negotiation command, the switch will negotiate the best settings for the RJ-...switch ASIC only supports symmetric pause frames.) Default Setting • 100BASE-TX: 10half, 10full, 100half, 100full • 1000BASE-T: 10half, 10full, 100half, 100full, 1000full • SFP: 1000full Command Mode Interface Configuration...

User Guide - Page 372

...channel. Ethernet Interface) used to select the backup link. Trunk index (Range: 1-32) Default Setting The ...configuring port trunks before you connect the corresponding network cables between switches to avoid creating a loop. • A trunk can only be made for a port to be allowed to join a channel group. • If a link goes down, LACP port priority is used by the interfaces...

User Guide - Page 374

... lacp {actor | partner} system-priority • actor - The local side an aggregate link. • partner - 4 Link Aggregation Commands Example The following shows LACP enabled on the ports at the other switches during LAG negotiations. (Range: 0-65535) Default Setting 32768 4-133 Console(config)#interface ethernet 1/11 Console(config-if)#lacp Console(config-if)#exit Console(config...

User Guide - Page 487

... connecting intermediate switches in the network, must be configured with a valid IP address, subnet mask and default gateway. • Be sure the management station has an IP address in the same subnet as the switch's IP interface to which it is connected. • If you are properly configured on the switch, and that the null-modem serial cable conforms to the pin-out connections...