Singer Futura Quartet Support Question
Singer Futura Quartet Support Question
Find answers below for this question about Singer Futura Quartet.Need a Singer Futura Quartet manual? We have 1 online manual for this item!
Question posted by albertalee48 on March 18th, 2019
Singer Seqs-6000 Wont Turn On.
Is there a fuse on the singer seqs 6000? If so where can I locate it? it wont turn back on.
Current Answers
Related Singer Futura Quartet Manual Pages
Instruction Manual - Page 1
...inside the face cover 52 Special accessories 53 Helpful messages 54 - 55
For European version
Sewing machine Dimensions: 567 mm × 240 mm × 317 mm Mass of the equipment:... 26 Sewing on a button 26 Buttonholes 27 - 29
Using buttonhole foot, Procedure, Corded buttonholes Buttonholing with Futura Multi hoop 44 - 47 Helpful messages when embroidering 48
4. STARTING TO SEW Quick ...
Instruction Manual - Page 3
... foot and should be
used for needle plate
10. Bobbins 21. To install the FUTURA software, refer to the CD insert for most decorative sewing. Auxiliary spool pin
4. Screwdriver for the majority of your
7
Sewing machine is "system" of the machine and the software providing powerful option and capabilities. Buttonhole foot and underplate
17.
Scissors...
Instruction Manual - Page 4
... and your machine the first time. Set power/light switch at "OFF"
machine socket
2 1
Pin
3
POWER/LIGHT SWITCH
Your machine will not operate until the power/light switch is turned on the ...servicing the machine, or when changing needles or lights, etc., the machine must be operated
either with a spool cap to wipe off any surplus oil from needle plate area before using sewing machine only. ...
Instruction Manual - Page 7
Turn the hand wheel counter clockwise (toward you should detect only a slight resistance and little or no deflection of the needle.
2.) Now lower the presser foot and again pull the thread towards the back of the Automatic Needle Threader.)
IMPORTANT: To verify that the machine...THREAD
A. Raise the presser foot lifter. Thread the machine with your left hand while firmly gripping the thread ...
Instruction Manual - Page 9
5
HELPFUL SUGGESTIONS: Put a drop of sewing machine oil onto the felt disc,
if the machine is deviated from needle hole,
adjust the position of the hook using a small screw
6
driver.
If the threading hook cannot catch thread, adjust the vertical position by bending the twin thread guide.
9
Felt disc
If the threading hook is used after a long interval.
Instruction Manual - Page 10
... 14/90
blue band 16/100 purple band
* For best sewing results, always use a Singer Branded Needle.
Remove the needle by turning it downward.
4. Tighten the needle clamp screw firmly with the... type of weight. The following table is used in the upper thread.
Always disconnect the machine from the wall-outlet. NEEDLE, THREAD AND FABRIC CHART
Your fabric will determine the choice of...
Instruction Manual - Page 11
... top and bobbin threads. You will be less than that the machine is usually only desirable for straight stitch sewing.
Under side
Well balanced
Top side
Top stitch too tight
Top ... of the fabric you are sewing. Make all adjustments with the foot holder.
3.
Place the desired foot on top of the machine. ADJUSTING TOP THREAD TENSION
90% of your sewing will always obtain a nicer stitch...
Instruction Manual - Page 13
...turns on when twin needle sewing is activated. At each of the potential adjustments. Stitch length and width/needle position controls
*Auto/Default settings Your sewing machine... needle sewing can manually change the length, width or straight stitch needle postition according to your stitching requirements at the Auto position, slide the control knob left or right to locate each ...
Instruction Manual - Page 14
NEEDLE STOP POSITION SELECTOR BUTTON
When the machine is turned on all patterns. Push it again and it will ... machine malfunctions.
6. The machine will return to start.
Red light indicates machine is set at its up -stop
3
position with LED lit. SPEED CONTROL LEVER
Sliding the lever sets desired sewing speed. The sewing machine makes 4 tiny tacking stitches to sew in...
Instruction Manual - Page 17
.../stop the sewing machine. Place the fabric under the presser foot toward you ) until the needle is in its center position. Guide the fabric gently with the thread cutter located on the bobbin... rear side) G. First turn the handwheel counter clockwise (toward the back of the
face cover, as an aid for guiding your hands. Presser foot lifter H. Turn the hand wheel counter clockwise...
Instruction Manual - Page 30
... up and down together with the needle. PREPARATION FOR EMBROIDERY SEWING
BEFORE ATTACHING EMBROIDERY UNIT ATTACHING EMBROIDERY FOOT
Always be sure to machine CAUTION before changing presser foot. Needle clamp Embroidery presser foot
INSERTING...holder Screw
* Raise presser foot lifter.
* Turn the hand wheel counter clockwise (toward you ) until the needle is above the needle clamp.
3.
Instruction Manual - Page 32
..., carefully slide toward the left while pressing release lever.
REMOVING EMBROIDERY UNIT
* Turn off the machine. * Remove embroidery hoop from machine.
(Refer to close for general sewing.
3
Handle
1
Release lever
2
Handle
Release lever
32 Slide the embroidery unit onto machine fitting connectors on the embroidery unit while attaching or during the embroidering process...
Instruction Manual - Page 38
... finish when it has reached to continue. Simply click on your computer and sewing machine.
1.
You can always abort the installation procedure by turning the Hand wheel towards you to free some hard disk space before proceeding with to open the Futura software. Next attach the embroidery unit to your embroidery unit.
3. Pressing the...
Instruction Manual - Page 44
... been marked onto the fabric. Please note: Up to three additional hoops will therefore sew the design to the alignment of cross lines must be sent to the machine to stitch out, while making it and sew accordingly.
Preparing the Fabric P l e a s e n o t e : T h e f ...Multi-Hoop
Multi-Hooping is a special feature in the Futura QuartetTM software that will allow embroidery data which is ...
Instruction Manual - Page 50
... lever is too tight. -
Fabric puckers. * Top thread tension is not raised when sewing stitch patterns.
- Shorten
stitch length. (see page 49). Turn on the switch. (see page 10). Machine jams/knocks. * Thread is being pulled or pushed against machine feeding
action. - Guide it gently. * Needle size is not correct for thread and fabric...
Instruction Manual - Page 51
....
(1)
1. CLEANING HOOK AREA AND FEED DOGS
1
Always disconnect the machine from power CAUTION supply by the arrows. (A, B)
NOTE: Singer Brand Sewing Machine Oil is at all purpose" oil as it is not suited for removal.
3. Remove two screws on the hook race as illustrated for sewing machine lubrication.
5. Replace the bobbin case with the lint brush...
Instruction Manual - Page 52
.... Use of sewing machine oil to your machine.
For the machine used . Screw
2
Screw
52 Put one drop of oil other than Sewing Machine Oil will cause damage to the points indicated
by arrows.
1
Face cover
Helpful Hints : For the machine used frequently : It should be oiled before oiling.
For best results always use SINGER Brand Sewing Machine Oil. Remove...
Instruction Manual - Page 53
...the Twin Needle Mode prior to normal sewing mode, either press the Twin Needle Button again or shut the machine off. NOTE on starting to sew with satin stitch foot: Pull both ... result in order to the General Purpose Foot when sewing stretch stitches. Slightly loosen top thread tension for sewing satin stitches. Use a backing of a Singer Brand twin needle (Style 2025) is most useful ...
Instruction Manual - Page 54
... stop .
On control panell
On PC screen
Problem Correction
Sewing Embroidery
Machine is detected on control panel and/or PC screen. is locked up due to thread entangled around spindle or
○ ○ rotation interrupted forcibly. Turn off power switch and eliminate the problem that caused the
02
bobbin winder to...
Instruction Manual - Page 60
... contact a qualified electrician to be followed, including the following to fit in this sewing machine. "To disconnect, turn switch to break." 17. "Do not unplug by or near children." 2. "Keep..., and loose cloth." 7.
To reduce the risk of The Singer Company Limited or its affiliates. ©2010 The Singer Company Limited or its intended use only." 9.
This appliance complies...
Similar Questions
Where Can I Get Replacement Parts For My Futura Quartet 6000 Machine?
(Posted by treasuredjewels2321 7 months ago)
I Was Sewing And All Of The Sudden My Machine Turned Off
(Posted by mari0624 3 years ago)
I Get E7 Error Message On My Singer Model 7258 Sewing Machine. There Is No Refe
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
(Posted by ebellamybellamy9 5 years ago)
Beeping From Singer Sewing Machine Stylist Ii 5625
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
(Posted by arusheria 9 years ago)