Singer 9970 Support Question
Singer 9970 Support Question
Find answers below for this question about Singer 9970.Need a Singer 9970 manual? We have 1 online manual for this item!
Question posted by joycejones1 on October 8th, 2013
Trying To Wind Bobbin With Green Light On, But No Success. What Am I Doing Wrong
The LCD panel iluinated bobbin wind, but I get no power to wind even though I pushed the green start and stop light. I have pushed the bobbin to the right where it clicked into place. Thisis a brand new gift and I am trying to get started. I have used my mother's old Singer machine for years, but I am stumped.
Current Answers
Related Singer 9970 Manual Pages
Instruction Manual - Page 2
... fingers away from outlet. 9. The wrong plate can cause the needle to lift and move the machine. 18. Switch the sewing machine off position (symbol "O"), then remove plug from all instructions before using and before cleaning. This sewing machine is used as described in a very warm or damp place. INSTRUCTION MANUAL
This sewing machine is not working properly, if...
Instruction Manual - Page 3
... K. INSERTING THE BOBBIN 15
THREADING THE MACHINE 16
A. DRAWING UP THE BOBBIN THREAD 17
STARTING TO SEW 18
A. SEWING OVER OVERLAPPED AREAS 20 G. MIRROR/REVERSE STITCH 22 D. QUILTING 27 C. USING THE OVERCASTING FOOT 29 B. THREAD SHANK 39
NARROW HEMMING 40 CORDING 40
A. EDITING OF EACH PATTERN 52 G. TO RECALL THE SELECTED PATTERNS 53 H. START/STOP BUTTON 10 B. TACK...
Instruction Manual - Page 4
... appliance.
Fuse must be supervised to ensure that you are colored in sewing from light to heavy material.
Blue: neutral (N) Brown: live (L)
As the colors of the wires in the mains lead of this sewing machine. EU only
1. MODEL 9970
PREFACE Thank you for your sewing machine, read the entire instruction manual before attempting to operate the...
Instruction Manual - Page 5
... Screw 23. Needle Thread Guide 24. Bobbin Cover Latch
27. Decorative Stitch & Letter Button
48. Power Switch 54. Needle Up-Down / Slow Button 5. Start/Stop Button 7. Presser Foot Release Lever 17. Feed Dogs 21. Thread Take-Up Lever (Inside) 28. Bobbin Winder Stop
37. Clear Button 41. Liquid Crystal Display (LCD) 38. Utility Stitch Button 47. Speed...
Instruction Manual - Page 8
..., fine cotton, machine quilting
2000 gray shank
11/80-14/90
Heavy Weight -
Place needle on a flat plate to the back and push it up as ...new needle into needle clamp with fabric to be sewn. Do not use the bent or blunt needle.
Type of Fabric
Thread Size
Needle Type
Needle Size
Light Weight - INSERTING THE NEEDLE
Select a needle of the right type and size for this machine...
Instruction Manual - Page 9
... PLUG INFORMATION This appliance has a polarized plug (one way. If it . 3.
Place foot controller at your foot. The harder you press the foot controller, the
faster the machine will permit control of start /stop button will light up when switch is released. The machine will light up when switch is intended to fit in any way.
Handle...
Instruction Manual - Page 10
... . Note: Machine will sew forward. MONITOR LAMP Green Light "ON" Ready to down position or buttonhole lever is not lowered. B. Note: When the foot controller is lifed up to sew or bobbin winding. D. PRESSER FOOT LIFTER The presser foot is connected, start of sewing. Red Light "ON" Presser foot is not in reverse at start /stop button will not start even when start/stop button...
Instruction Manual - Page 14
... in bobbin and place the bobbin on spool pin so that the thread unrolls from rear opening between cap and spool as it will go. Push bobbin to the right to the right and remove
the bobbin cover. 2. After the bobbin winds a few turns, stop the machine by pressing the start /stop automatically when bobbin is full. (Release the pedal.) 9. The bobbin winding will indicate the bobbin winding...
Instruction Manual - Page 15
... out of bobbin cover down until it clicks into the hole in this machine.
15
INSERTING THE BOBBIN 1. Pull thread out about 10 cm (4 inches). NOTE: Be sure to use only SINGER (Class 15) bobbins in needle plate and push the right side of notch (a).
4. Pull thread toward the left tab into place. Replace the bobbin cover. Place bobbin into notch...
Instruction Manual - Page 17
...Pull thread out about 10 cm (4 inches) toward the right. 4.
DRAWING UP THE BOBBIN THREAD 1. Hold thread loosely and press needle up/down button. Pull upper thread lightly.
Note: If desired, you can draw up /down... presser foot.
17 Keep fingers away from needle eye. Do not lower the threader lever while machine
is used for needle sizes 11/80, 14/90, and 16/100.
1. E. Note:The...
Instruction Manual - Page 18
... threads and press the start / stop button to stop button or press the foot controller pedal. When you cut the threads. Check the presser foot (General Purpose
Presser Foot). Keep holding threads after sewing a few stitches. Press the thread cutter button. 6. CAUTION 1. STARTING TO SEW
The machine will be set to sew straight stitch when power switch is required...
Instruction Manual - Page 25
... and bobbin thread
loosely and start sewing. Press the thread cutter button.
25 Place hand lightly on the fabric while sewing.
3. No. 1. Center needle with built-in reverse stitch No. 4. Position the fabric under the presser foot and
lower it .
2. B. Machine will sew a few stitches backward and sew a few stitches forward and stop sewing. 4. Machine will sew 4-5 stitches...
Instruction Manual - Page 26
...holder. (See page 7)
3.
Hold the upper thread and bobbin thread
loosely and start to right so that it is fitted into the presser bar.
5. Machine will be reduced automatically. 1.
Tighten the presser foot thumb ...of the needle clamp screw.
4. Pull the fabric required amount to the left to sew. Place the fabric under the presser foot and then
lower the presser foot lifter. 2. ...
Instruction Manual - Page 27
... thread that you sew, bobbin thread will give the appearance of a traditional hand quilting stitch.
27 Bag
b. The top layer is formed by shaped pieces of material. Place thread that contrasts ... / Patch Quilting Foot Quilting Bar
CAUTION: To prevent accidents. Set the upper tension to sew successive rows. The topper, batting, and backing fabric. Trousers d. Joining the pieces of fabric...
Instruction Manual - Page 30
... Fold the fabric as shown on drawing. Light weight fabric c. The guide (e) on the blind foot ensures even feeding of fabric h. Lower the presser foot and sew hem, guiding fabric evenly along the guide.
5. Wrong side of the fabric when blind hem stitching. Blind Hem Foot (D)
1. Right side of fabric. BLIND HEM STITCHING
The...
Instruction Manual - Page 34
... upper thread through the hole of button. This machine can sew 13 types of the buttonhole may be adjusted with stitch length control.
1. Stretch Buttonhole 115. Hold upper thread lightly and start to diameter of button plus thickness of buttonhole foot and bring upper and bobbin threads to sew. Set button on the backside of the...
Instruction Manual - Page 39
...sewing machine needle under the center slit of presser foot and lower foot to form a firm shank. Align two holes of the button with slot of the foot from the fabric. You may break.
5. CAUTION: To prevent accidents. Pull the end of bobbin thread and pull upper thread to the wrong... need to the right.
Tie thread ends securely.
39 SEWING ON BUTTONS
No. 13
Button Sewing Foot
1. Lower ...
Instruction Manual - Page 46
... sure you start to sew.
4. It works best with sequins. Tighten the side screw securely. 2. The stitch length dial can also be used for gathering or shirring fabrics. Set the machine to Straight Stitch. 4. Place the fabric to adjust fullness. Set the machine to Straight Stitch. 5. Less tension will result in the Gathering Foot's slot...
Instruction Manual - Page 57
... and dust accumulated around bobbin. Machine will not run
Cord not plugged into outlet. Re-thread the bobbin.
15
breaks
Bobbin wound unevenly or too full. Rewind the bobbin.
14
Dirt or lint on stretch fabric)
Re-insert needle.
8
Insert new needle.
8
Choose correct size needle for the pattern. Push spindle to the right. Blunt needle.
Incorrect size...
Instruction Manual - Page 58
Winding the bobbin.
1
2. After sewing buttonhole, raise the presser foot
3
lifter and set the frame of buttonhole foot to
starting position.
4. Lower the presser foot.
5
6. Release the foot controller pedal.
4
5. Release the start/stop button.
9
10.Rethread the upper thread.
10
11.Foot controller is full.
6
7. Release the reverse button.
8
9. Machine memory is ...
Similar Questions
Classes On How To Use Singer 9970 Sewing Machine
I bought the sewing machine during the pandemic and would like to learn how to use it- functions, st...
I bought the sewing machine during the pandemic and would like to learn how to use it- functions, st...
(Posted by Connienm 1 year ago)
Top Thread Sticking On Bobbin Case
I am having a problem with the top thread catching on the bobbin case and breaking the thread. I had...
I am having a problem with the top thread catching on the bobbin case and breaking the thread. I had...
(Posted by mvieira10 5 years ago)
I Get E7 Error Message On My Singer Model 7258 Sewing Machine. There Is No Refe
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
(Posted by ebellamybellamy9 5 years ago)
Why Won't My Machine Sew, Checked Bobbin And Retreaded. Has Power Just Will Not
the machine has power and threade correctly and bobbin is in right. It did freeze on me when sewing....
the machine has power and threade correctly and bobbin is in right. It did freeze on me when sewing....
(Posted by alewis41 7 years ago)
Beeping From Singer Sewing Machine Stylist Ii 5625
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
(Posted by arusheria 9 years ago)