Sharp PN-E702 Support Question
Sharp PN-E702 Support Question
Find answers below for this question about Sharp PN-E702.Need a Sharp PN-E702 manual? We have 1 online manual for this item!
Question posted by dinayoung215 on September 19th, 2021
Don't Have A Remote
I have a sharp tv that don't work. I click the switch but powrr light came on. What should I do?
Current Answers
Answer #1: Posted by techyagent on September 19th, 2021 8:00 PM
techyagent
Member since:
June 17th, 2014 Points: 4,799,790
Member since:
June 17th, 2014 Points: 4,799,790
Please check this link below:-
https://www.amazon.com/Control-Originally-Shipped-PN-E702-PN-L601B/dp/B078TB57RZ
https://business.sharpusa.com/portals/0/downloads/Manuals/PN_E702_Operation_Manual.pdf
Thanks
Techygirl
Answer #2: Posted by SonuKumar on September 20th, 2021 1:21 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,614,400
Member since:
May 9th, 2021 Points: 16,614,400
Check if it universal remote, then there is posilbiltiy of sync otherwise not
https://www.sears.com/sharp-8057727-new-oem-sharp-remote-control-originally/p-A015855277
https://www.amazon.com/Control-Originally-Shipped-PN-E702-PN-L601B/dp/B078TB57RZ
https://business.sharpusa.com/portals/0/downloads/Manuals/PN_E702_Operation_Manual.pdf
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Sharp PN-E702 Manual Pages
PN-E702 Professional LCD Monitor Operation Manual - Page 6
... the edge of batteries may vary. • Replace an exhausted battery with a new one promptly. • If you will not use the remote control for child safety
-
Care
should be taken to route all cords and cables connected to the monitor so that they cannot be potentially hazardous due to reach the...
PN-E702 Professional LCD Monitor Operation Manual - Page 8
...the remote control sensor or buttons.
2 [5]
* This monitor can be tilted up to 20
degrees upward or downward.
• This monitor should never attempt to perform any reason such as the monitor ... be outside of the range of this
work must be performed by SHARP. Provide
enough space around the monitor to stress the terminal of the monitor inside a housing, or if the ambient...
PN-E702 Professional LCD Monitor Operation Manual - Page 9
...installing the expansion board PN-ZB01 (optional). C over Sharp logo: 1
Place this sticker onto the SHARP logo to cover the logo.
* Sharp Corporation holds authorship rights... Precautions (For SHARP dealers and service engineers 56
Supplied Components
If any component should be missing, please contact your dealer.
Liquid Crystal Display Monitor: 1 Remote control unit: ...
PN-E702 Professional LCD Monitor Operation Manual - Page 10
...to press the
switches at the front of the monitor.
2
3
4
5
nRear view
When the PN-ZB01 (optional) is attached
15
16
1
17
18
19
20
22
21
23 24
5
6
7
8
9
11
10
12
2
Caution • Consult your SHARP dealer for attachment... component input terminals (See page 13.) 23. Offering this terminal is attached 15. Remote control sensor (See page 15.) 3.
E 10
13 14
1.
PN-E702 Professional LCD Monitor Operation Manual - Page 12
...cable (conforming to
the HDMI standard). • Set HDMI of the output sound can control the monitor from the
audio output terminals with AV VIDEO (D-SUB), connect the green terminal to the device's ... Peripheral Equipment
When the PN-ZB01 (optional) is attached 6
14 12 13
11
1
8
7
9 10
2 3 4
5
5
Caution
• Be sure to turn off the main power switch and disconnect the plug from...
PN-E702 Professional LCD Monitor Operation Manual - Page 13
... terminals other than PC DVI-D/AV DVI-D for the input mode. While pushing the tab, insert the tip of the speaker cable connected to the monitor.
2. Connecting Peripheral Equipment
Connection when the PN-ZB01 (optional) is set to AV COMPONENT.
9.
AV component input terminals • Set BNC of up to...
PN-E702 Professional LCD Monitor Operation Manual - Page 16
...
Caution • Turn on the monitor first before turning on the remote control unit, the monitor enters standby mode.
• Setting the SCHEDULE flashes the power LED alternately in red and orange in a malfunction.
TIPS
• When the main power switch is on. • When switching the main power switch or the POWER button off and...
PN-E702 Professional LCD Monitor Operation Manual - Page 18
...the terminal to the
previous level.
2
3.
DISPLAY Displays monitor information. MODE (Color mode selection) Each time you do ...mode, and press to PC input only. When the PN-ZB01 (optional) is made in the following order:
STD...is international standard of color representation specified by pressing the input
switch of liquid crystal's characteristics and represents color tone close to...
PN-E702 Professional LCD Monitor Operation Manual - Page 20
...MENU]
For items that cannot be displayed only when the PN-ZB01
(optional) is attached.
SCREEN PICTURE
AUDIO SETUP OPTION...
31
CONTRAST
30
BLACK LEVEL
30
TINT
30
COLORS
30
SHARPNESS
12
RGB INPUT RANGE
PC D-SUB FULL
MOVE OSD·... of each menu items.
Caution
• Do not turn the main power switch off while the menu items are enabled.
TIPS
• Items that have press...
PN-E702 Professional LCD Monitor Operation Manual - Page 23
...setting details such as the state where no operation from the remote control unit, RS-232C commands, or LAN for the monitor connected to LOW POWER, certain RS-232C commands cannot be used... this as ANALOG GAIN, ANALOG
OFFSET, and DISPLAY COLOR PATTERN cannot be copied to the monitor connected to the RS-232C output terminal and to 255 are automatically allocated.
Note, however that...
PN-E702 Professional LCD Monitor Operation Manual - Page 24
...BEZEL (BOTTOM) / BEZEL (RIGHT) / BEZEL (LEFT)
..........Sets the frame width of monitors are aligned in multiples to switch modes from the built-in the horizontal/vertical direction used for AV mode input. POWER ...is present in multiple input modes, the switching priority is as follows: PC D-SUB, PC HDMI, AV HDMI, AV COMPONENT and AV VIDEO
When the PN-ZB01 (optional) is present. Menu Items...
PN-E702 Professional LCD Monitor Operation Manual - Page 29
...the FUNCTION operation is attached, press , select the resetting method, and then press MENU . REMOTE CONTROL Prohibits remote control
operation MONITOR BUTTONS ��� Prohibits monitor switch
operation BOTH Prohibits remote control and
monitor switch operation
RS-232C (RS-232C/LAN when the PN-ZB01 (optional) is LOW POWER. The FUNCTION screen cannot be selected when STANDBY...
PN-E702 Professional LCD Monitor Operation Manual - Page 30
... value, specify a numerical value in the "RS-232C command table" on the PC to match the monitor's communication settings as follows:
Baud rate Data length Parity bit
* 8 bits None
Stop bit
1 bit... terminal on the first monitor.
Precautions when the PN-ZB01 (optional) is sent from a PC via RS-232C, set all monitors to the third and subsequent monitors. Example: AUTR-005
Do...
PN-E702 Professional LCD Monitor Operation Manual - Page 34
... Monitor with...INPS
W
0
1
2
3
4 6
7
8 9
10
R
Reply
Control/Response contents
*2 *1
(A) (B)
Switches to LOW POWER. Terminals not selected in power standby mode when STANDBY MODE is set to standby mode. AV ... mode regardless of the STANDBY MODE setting.
PN-ZB01 (optional) limitations
(A) When PN-ZB01 (optional) is not attached, (B) When PN-ZB01 (optional) is selected for input mode...
PN-E702 Professional LCD Monitor Operation Manual - Page 37
... the settings. 0: OFF, 1: ON
*2 *1
(A) (B)
○○ ○
○○○
○○○
37 E Displays monitor's own ID number and the selected ID number on the screen. 0: OFF, 1: ON, 2: ON (turns OFF after 4 sec.) (When the PN-ZB01 is selected for the command immediately after this command. SETTING IDLK
W
(SUBSEQUENT)
ID CHECK...
PN-E702 Professional LCD Monitor Operation Manual - Page 40
... WR
TALT
WR
SALT
WR
PBTN WR
PCIP
WR
Parameter
0 0-1 0-2 0-2 0-2 0-1
0-2 0-2 0-1 0-2
Reply
Control/Response contents
0: ALL RESET 0: ALL RESET 1, 1: ALL RESET 2 0-2 0: OFF, 1:ON1, 2:ON2 0-2 0: REMOTE CONTROL, 1: MONITOR BUTTONS, 2: BOTH 0-2 0: ON1, 1: OFF, 2: ON2 0-1 0: ON, 1: OFF "ERR" when LOW POWER is selected for STANDBY MODE. 0-2 0: OFF, 1: OSD & LED, 2: LED 0-2 0: OFF, 1: OSD & LED...
PN-E702 Professional LCD Monitor Operation Manual - Page 42
... through). Network (LAN)
LAN terminal Hub
LAN cable (commercially available, straight)
TIPS • You must be installed with a PC (LAN)
When the PN-ZB01 (optional) is attached, your monitor can be assigned automatically. (See page 23.)
E 42 DEFAULT GATEWAY If the DHCP CLIENT is set to match the settings of your LAN...
PN-E702 Professional LCD Monitor Operation Manual - Page 49
... linked URL.
49 E ■ SNMP
You can check whether the URL you set SNMP, click [Switch the main power of
monitor off and on now.] or turn off the monitor and then turn it on again with the main power switch.
When this function is enabled, a trap will be used for access.
USER 1 to display...
PN-E702 Professional LCD Monitor Operation Manual - Page 52
... figures indicated are nominal values of continuous improvement, SHARP reserves the right to STANDARD.
Specifications
nProduct Specifications
Model
PN-E702
LCD component
70" Class [69-1/2 inch (176...PAL-60/SECAM
Plug and play . *3 Temperature condition may change when using the monitor together with the optional equipments recommended by the optional equipments. *4 When AUTO INPUT CHANGE...
PN-E702 Professional LCD Monitor Operation Manual - Page 53
...Yes No
Vsync
Yes Yes No No
DMPM: Digital Monitor Power Management
DMPM
Monitor ON Active OFF
Screen
Display No display
Power consumption
235 W*1 1.0 W*1*2
*1 When PN-ZB01 (optional) is not connected. *2 When AUTO...configured to detect plug-and-play monitors. SHARP recommends using M6 screws and tighten the screws. nPower management
This monitor conforms to work. Both your video card and ...
Similar Questions
Hi So I Purchased A Sharp Pn-l702b And It Keeps Turning Off On Me Plz Suggestion
(Posted by Raduudila1990 1 year ago)
The Monitorcomes On But U Can Only See The Screen If You Hold A Flash Light To M
to the monitor. Also the touchscreen dont seem to work either. Screens dark settings dont help and t...
to the monitor. Also the touchscreen dont seem to work either. Screens dark settings dont help and t...
(Posted by mwing 2 years ago)
Frequent On Off
We have sharp 70 " LED PN-E702 having No. 25051759 . we are using this monitor in a power station fo...
We have sharp 70 " LED PN-E702 having No. 25051759 . we are using this monitor in a power station fo...
(Posted by ashrafsiddiqi79 7 years ago)
My Monitor Shuts Itself Off After A Few Seconds.
Help! Please!
Help! Please!
(Posted by shelaworkfromhome 9 years ago)