Ryobi TSS103 Support Question
Find answers below for this question about Ryobi TSS103.Question posted by island2discover on August 22nd, 2023
Light Won't Work How To Fix It
Current Answers
Answer #1: Posted by INIMITABLE on August 22nd, 2023 12:48 PM
- Remove the cover. There are a series of screws holding the casing over top of the miter saw and the laser. You will need to remove them to gain access. When you get the cover and plastic guard out of the way, you should see a set of screws as well as a hex screw beneath.
- Remove the screws. To access the laser itself, take the screws out here. It will give you better access to the laser itself.
- Wipe. Using a cotton alcohol wipe or a soft cloth, give the laser a good wipe. If there is a buildup of dirt and debris over top of the laser, this should remove it.
- Replace and try again. When you are confident that the laser has been properly cleaned, return everything back to its original condition. Make sure that the cover is secure and then try to use the laser again. If it still doesn't work, keep reading.
Please follow the link below for visual aid to fix that; https://www.youtube.com/watch?v=bXr_f0j1UNc
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers
-INIMITABLE
Answer #2: Posted by SonuKumar on August 22nd, 2023 10:36 PM
Check the power cord. Make sure that the power cord is plugged into an outlet and that the outlet is working. You can test the outlet by plugging in another appliance.
Check the fuse. The TSS103 has a built-in fuse that can blow if there is a power surge or short circuit. To check the fuse, you will need to remove the back panel of the light. Once the back panel is removed, you will see the fuse located in a holder. To remove the fuse, you will need to use a fuse puller. Once the fuse is removed, you can inspect it to see if it is blown. A blown fuse will have a broken or melted link.
Check the light bulb. The TSS103 uses a standard light bulb. Make sure that the light bulb is screwed in tightly and that it is not burned out.
Check the switch. The TSS103 has a switch that turns the light on and off. Make sure that the switch is turned to the "On" position.
If you have checked all of these things and the light still does not work, then you may need to replace the light. You can find replacement lights at most hardware stores.
Here are the steps on how to check the fuse in a Ryobi TSS103 light:
Turn off the light and unplug it from the outlet.
Remove the screws that hold the back panel in place.
Remove the back panel.
Locate the fuse. It is a small, cylindrical component located near the power connector.
Use a fuse puller to remove the fuse.
Inspect the fuse to see if it is blown. A blown fuse will have a broken or melted link.
If the fuse is blown, replace it with a new fuse of the same amperage.
Reinstall the back panel.
Plug the light back into the outlet and turn it on.
If you are not comfortable checking the fuse yourself, you can take the light to a qualified technician.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Similar Questions
my crimper is stuck in cycle mode and fault light is blinking and tool won't work now
What does it mean when both yellow & green light come on when trying to recharge batteries?
Cleared jam, due to brads not adhered together. New pack bought, newly charged battery. No sign of p...
I have a brand new Ryobi TSS101L and I see no evidence of a laser working. I looked through the manu...
I just bought a circular saw model CSB142LZ and for some reason when I plug it in the blue light com...