Ricoh FW780 Support Question
Find answers below for this question about Ricoh FW780.Need a Ricoh FW780 manual? We have 2 online manuals for this item!
Question posted by engineerhanif on September 22nd, 2014
Rico Fw740 Error Code E-3
my rico fw 740 give error code E-3.please give some helpful soloution.
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Ricoh FW780 Manual Pages
Operating Instructions - Page 60
... local reg- E Plug in the copier again, and then close the door.
ulations. Do not throw away the bottle.
Maintaining Your Copier
B Unplug the code from the mainframe. C Open the door on the right side of the copier ,and then carefully remove the
plastic bottle.
4
Note ❒ Put the used ...
Operating Instructions - Page 92
nostic
cators
codes
Power Source
North America: 120V, 60Hz, 12A
Europe: 220-240V, 50/60Hz, 7A
Power con- LED indi- Maximum sumption 1.4kW
Noise emission
Stand by: less ...
Service Manual - Page 11
NO.
* 1 2 3 4
DATE
5/95 5/96 6/98 8/2001
COMMENTS Original Printing Revised Pages Reprint A251/A252 Addition B047/B048 Addition LEGEND
PRODUCT CODE
A163 A251 A252 B047 B048
GESTETNER N/A N/A N/A A040 A041
COMPANY
RICOH FW740 FW750 FW760 FW770 FW780
SAVIN N/A N/A N/A
7700W 7800W
DOCUMENTATION HISTORY
REV.
Service Manual - Page 20
...Lamp Abnormal 6-7 2.2 SC Code E-2: Fusing Thermofuse Open 6-7 2.3 SC Code E-3: Hot Roller Thermistor Open 6-8 2.4 SC Code E-4: Hot Roller Thermistor Short 6-8 2.5 SC Code E-5: Pressure Roller Thermistor Open 6-8 2.6 SC Code E-6: Pressure Roller Thermistor Short 6-9 2.7 SC Code E-7: Fusing Overheat 6-9 2.8 SC Code E-8: Fusing Warm-up Error 6-10 2.9 SC Code E-9: Toner Density Sensor Abnormal...
Service Manual - Page 26
... optional)
Image Fusing:
Heat and pressure type, teflon (upper) and silicone rubber (lower) rollers
Fusing Lamp:
Nichrome wire lamp (115 V: 1,100 W, 230 V: 1,100 W)
Self-diagnostic Codes:
11 codes, displayed in copy counter
Power Source:
115 V/60 Hz....15 A 220 V/50 Hz....7 A 230 V/50Hz.....7 A 240 V/50 Hz....7 A
Power Consumption:
Maximum: Warm-up: Ready...
Service Manual - Page 108
... cleared when the new developer initialization is installed. dt = XX,XXX This counter is automatically cleared when the new toner cartridge is done.
Misfeed location codes displayed Jt = Total Jam in each SP number are as follows: SP80: Jt, J90, J98, J99 SP81: J01, J02, J03, J04 SP82: J20, J21, J22...
Service Manual - Page 109
... = XX (1 before
the last error code)
↓ E3 = XX (2 before
the last error code)
↓ E4 = XX (3 before
the last error code)
↓ E5 = XX (4 before
the last jam) ↓ Beeper (XX = Jam Location)
Displays the total number ...XX (2 before
the last jam) ↓ J4 = XX (3 before
the last jam) ↓ J5 = XX (4 before
the last error code)
↓ Beeper (XX= Error Code)
SM
4-17
A163
Service Manual - Page 123
Read the jam code.
4.2 JAM CODE TABLE
Code PJ01 PJ02 PJ03 PJ04 PJ05
PJ20 PJ21 PJ22 PJ23 PJ30 PJ31 PJ32 PJ40
PJ41 PJ42 PJ43... ON during the roll feeding. 4.
Registration sensor ON check at the paper leading edge.
Door open during the roll feeding. JAM CODE LIST
When a document (original) jam or paper jam occurs, the cause of the roll feeder. Initial misfeed at the paper leading...
Service Manual - Page 124
Code PJ90 PJ98 PJ99
Cause of Jam Roll feeder. Original registration sensor does not turn off after paper is fed 500 mm more than the maximum paper length. motor does not turn off after paper is fed 2500 mm.
SP Mode No.
SP80 (Others)
Registration sensor does not turn off after paper is fed 2500 mm. A163
4-32
SM
NOTE: To display total jam number, access SP mode No. 80.
Service Manual - Page 130
... lights. Select Lamp Off Mode with vertical grain direction. If "Lead Margin" indicator does not light, press Function Select key until "Lead Margin" indicator lights.
FW740-010 for more information regarding the proper settings for non-listed papers. Be careful not to damage the edges of paper and the adjustment procedure...
Service Manual - Page 186
... drive board ( T202-2, RA201-T4) Fusing thermofuse Main board (CN106-A2, -A5, -B11, -B14, -B15)
2.4 SC Code E-4: Hot Roller Thermistor Short
-DefinitionThe resistance of the pressure roller thermistor is more than 0.11 KΩ. 2.3 SC Code E-3: Hot Roller Thermistor Open
-DefinitionThe temperature detected by the hot roller thermistor does not reach 50°...
Service Manual - Page 187
... drive board (T202-2, RA201-T4) Main board (CN106-A2, -B14, -B15)
SM
6-9
A163 Pressure roller thermistor Main board (CN106-A2, -A5, -B11, -B14, -B15)
2.7 SC Code E-7: Fusing Overheat
-DefinitionThe temperature detected by the hot roller thermistor becomes higher than 0.55 KΩ.
Service Manual - Page 188
... (T202-2, RA201-T4) Main board (CN106-A2, -A5, -B11, -B14, -B15) AC harness
2.9 SC Code E-9: Toner Density Sensor Abnormal
-DefinitionThe toner density sensor voltage is not detected until 251 copies since initializing
developer. 2.8 SC Code E-8: Fusing Warm-up Error
-DefinitionThe temperature detected by the hot roller thermistor does not reach the target ready...
Service Manual - Page 189
Main motor Mechanical interference of the main motor drive Main board (CN106-A12, -A13)
2.11 SC Code E-11: Toner Density Sensor adjustment Error
-DefinitionThe toner density sensor voltage cannot be adjusted to its next initialization. 2.10 SC Code E-10: Main Motor Abnormal
-DefinitionThe main board does not receive a signal from the main motor for...
Service Manual - Page 217
TABLE OF CONTENTS
1. SERVICE TABLES 4-1
4.3 SERVICE TOOLS 4-1
4.3.1 SERVICE PROGRAM MODE 4-1 4.3.2 INPUT/OUTPUT CHECK MODE 4-9
4.4 JAM CODE LIST 4-11
4.4.2 JAM CODE TABLE...4-11
4.6 SERVICE REMARKS 4-15
4.6.12 AC DRIVE BOARD 4-15
5. OVERALL MACHINE INFORMATION 1-1
1.1 SPECIFICATIONS 1-1 1.2 PAPER PATH 1-3 1.4 MECHANICAL COMPONENT 1-4 1.5 DRIVE LAYOUT 1-6 1.6 ELECTRICAL COMPONENT...
Service Manual - Page 313
... 6.2.1 SC CODE DESCRIPTIONS 6-1 SC Code E-1: Exposure Lamp Abnormal 6-1 SC Code E-2: Fusing Thermofuse Open 6-1 SC Code E-3: Hot Roller Thermistor Open 6-1 SC Code E-4: Hot Roller Thermistor Short 6-2 SC Code E-5: Pressure Roller Thermistor Open 6-2 SC Code E-6: Pressure Roller Thermistor Short 6-2 SC Code E-7: Fusing Overheat 6-2 SC Code E-8: Fusing Warm-up Error 6-3 SC Code E-9: Toner...
Service Manual - Page 314
... Motor Abnormal 6-3 SC Code E-11: Toner Density Sensor Adjustment Error 6-3 SC Code E-13: Total Counter Abnormal 6-4 SC Code E-14: Zero Cross Signal Detection Abnormal 6-4 SC Code E-15: Main Switch Abnormal 6-4 SC Code E-17: Unstable Fusing Temperature 6-4 SC Code E-18: Fusing Lamp Continuous Light 6-4 6.3 BLOWN FUSE TABLE 6-5 6.3.1 POWER SUPPLY UNIT 6-5 Europe Version 6-5 U.S.A. OVERALL...
Service Manual - Page 319
...1 roll * Roll Feeder, 2 rolls * Roll Cutting Rail * Table * Side Guide
1080 x 570 x 490 mm
174 lbs 79 kg
FW780 B048
Condole 60K Copies or 5 yrs
3.6K 36" X 118" Max. 3m / 9.8ft. N/A Manual Bypass
* 1 Roll Feeder * Roll...3.6K 36" X 118" Max. 3m / 9.8ft. Comparison of Major Specifications
Items
FW740 A163
Configuration Machine Life (A1/D Sideways) PM Cycle (A1/D Original Size Original Length ...
Service Manual - Page 415
... reach the target ready temperature within 12 minutes. SERVICE CALL CONDITIONS
SC Code E-8: Fusing Warm-up Error
Definition After turning on , but the main board does not receive a... Flow of the main motor drive • Main board (CN103-1, -2)
SC Code E-11: Toner Density Sensor Adjustment Error
Definition The new developer initialization process cannot adjust the toner density sensor voltage to ...
Service Manual - Page 476
... the revised areas ⇒.
!
INSERT
GENERAL:
The Service Manual pages listed below must be replaced with the pages supplied. PAGES:
• 4-25
Jam Code Table (Updated Information). FW770/FW780 SAVIN -
Each bulletin package contains 1 set of additional bulletins.
All rights reserved. TECHNICAL SERVICE BULLETIN
BULLETIN NUMBER: B047/B048 - 002
APPLICABLE MODEL: GESTETNER...
Similar Questions
Ricoh Fw780 Error Code 7 Hello, This Message Is Coming
Ricoh FW780 Error Code 7Hello, this message is coming
Ricoh FW780 Error Code 7Hello, this message is coming
(Posted by Abbas4 3 years ago)
My Rico Fw 740 Giveing E2 Error Code And Double Image
my rico fw 740 giveing e2 error code and double image come on each copy.plz give some soloution.
my rico fw 740 giveing e2 error code and double image come on each copy.plz give some soloution.
(Posted by engineerhanif 9 years ago)