Onkyo TX-DS595 Support Question
Onkyo TX-DS595 Support Question
Find answers below for this question about Onkyo TX-DS595.Need a Onkyo TX-DS595 manual? We have 1 online manual for this item!
Question posted by mistypetty1234 on March 25th, 2019
Debug Problem
so I have an Onkyo TX ds595 the power was on and I went to turn the power off and I got a debug code in Readin looooa lll 231?
Current Answers
Answer #1: Posted by waelsaidani1 on April 20th, 2019 6:50 PM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
1. How to enter the debug mode Press and hold down the AUDIO SEL button, then press the STANDBY/ON button to display "DEBUG MODE IN". After 5 second the unit enters the DEBUG mode. When there is the error that can judge by the microprocessor, the error message is displayed for 3 seconds.
DSPREAD ERROR: Problem of interface between DSP and microprocessor. DSPLOCK ERROR: Problem of lock of DSP IC.
On all occasions the microprocessor resets DSP, and DSP is restarted.
2. How to investigate the unit by the debug mode Apply the signal that the trouble occurs, and compare with the example of display or the normal unit. If there is difference on the display, you are able to check the rejection by the explanation below. If there is not difference, the input signal comes to DSP IC and the format of signal is recognized. Check the signal from the DSP output to the speaker output.
3. Explanation of Display 1. DIR ERROR: Check of digital signal of DIR IC (AK4112). L:There is the digital signal. H:No digital signal. When apply the digital signal, the display is "L". Check the circuit from digital input to DIR IC and the connection between ERF (#18) of DIR and microprocessor.
2. DIR STATUS 1: It displays the status of Addr03H that AK4112 reads from the digital signal. It shows the sampling frequency, and pre emphasis etc. When the display is difference to the table below, check the signals of DSPCL and DSPDA to confirm the communication between the microprocessor and CDTO/SCDO(#28) of AK4112.
3. DIR STATUS 2: It displays the status of Addr0DH that AK4112 reads from the digital signal. It shows the constants of input signal (DD,DTS,MPEG etc.). When the display is difference to the table below, check the signals of DSPCL and DSPDA to confirm the communication between the microprocessor and CDTO/SCDO(#28) of AK4112.
4. DIR analog/digital judgment It displays the result of judgment about input signal by the microprocessor. D:Digital A:Analog
5-7. Addr15 -17 :These displays show the port condition of the flash memory control. "L" except Japanese model.
Related Onkyo TX-DS595 Manual Pages
Owner Manual - Page 1
... 8 Connections 10 Connecting speakers 14 Connecting the power 16 Connecting antennas 17
Setup and operation
Speaker ...TX-DS595 ... 25 Using listening mode 28 Input Setup 29 Preference 32 Recording 33
Remote controller
Using remote controller 34 Learning a pre-programming code 38 Operating your new AV Receiver. Please read this manual will enable you for purchasing the Onkyo AV Receiver...
Owner Manual - Page 5
... corrosion. The STANDBY indicator lights up when the unit receives a signal from strong light such as direct sunlight or... and drain the batteries. • Make sure the audio rack doors do not have colored glass. Before using the...is appropriate. TX-DS595
R
L
CAUTION:
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
6 OHMS MIN. / SPEAKER
4 OHMS MIN. / SPEAKER
SET BEFORE POWER ON IMPEDANCE...
Owner Manual - Page 6
... below
4
5
6
STANDBY/ON
STANDBY POWER ON OFF
PHONES
DISPLAY RT/PTY/TP FM MODE PRESET MEMORY
TUNING
A SPEAKERS B
CH LEVEL
DSP/MODE ADJ
SETUP
PRESET
RETURN
PUSH TO ENTER SMART SCAN NAVIGATOR
AUDIO SELECTOR
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VCR
TAPE
FM
AM
PHONO
C D
MASTER VOLUME
BASS
TREBLE
AV RECEIVER TX-DS595
7
8
9
0A
B
C D EF
For all...
Owner Manual - Page 7
...TX-DS595 to enter and exit the setup mode. PHONES
AUDIO...POWER switch [16] Turns on and off the main power...to turn on the TX-DS595 front ...received from the most European countries. PHONES jack To listen with headphones, plug a pair headphones with a standard stereo plug into the Radio Data System (RDS) for the front speakers and headphones. STANDBY indicator [16] Lights when the TX-DS595...
Owner Manual - Page 8
... operation buttons [34-37] For operating Onkyo components connected to turn the power completely off automatically after a specified time ...AUDIO
TOCPHMSEENLU
TMEESNTU
MUTING
ANGLE
SUBTITLE
TV / VCR
LEVEL
RANDOM REC
OPEN / CLOSE
INPUT SELECTOR
DVD
C D
V 1
V 2
T 1
T 2
V 3
V 4
TUN
P H
STEREO
1
SURR
4
SP A
7
DISPLAY
+10
-- / --- ON/STDBY button [16]
ON: Turns on the TX-DS595...
Owner Manual - Page 10
...the power cord until all plugs and connectors securely. TX-DS595
R
L
CAUTION:
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
6 OHMS MIN. / SPEAKER
4 OHMS MIN. / SPEAKER
SET BEFORE POWER ON...
L
FRONT SPEAKERS B
AV RECEIVER
MODEL NO.
When not using an optical input jack, always use an optical fiber cable.
Connecting antennas [17]
Connecting your audio components [11]
Connect to ...
Owner Manual - Page 11
... a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT (OPTICAL) jack on the TX-DS595 depending on the type of connector on the device. Turntable (PHONO)
Digital audio output (optical) Analog audio output
L (White) R (Red)
Ground wire (earth)
Analog audio input
3.
With the initial settings of the TX-DS595, the CD input source is designed for digital input at the...
Owner Manual - Page 13
...Audio Setup → Digital Input (see page 29).
7. REMOTE CONTROL
z connector
TX-DS595
Ex: Onkyo CD player
z connector
Ex: Onkyo...8226; With Onkyo DVD players, you can enter the pre-program code so that ...TX-DS595 just like you properly connect the left channel to the L jack and the right channel to the R jack.
If the power cord for no digital input. If the digital connection is turned...
Owner Manual - Page 15
...audio will sound unnatural.
• Do not connect more speakers have an impedance of less than 4 Ω may damage the TX-DS595.
• Use FRONT SPEAKERS B terminals to connect a second pair of front speakers.
• When you wish to listen to monaural (mono) sound, a single speaker should never be turned... SPEAKERS B
AV RECEIVER
MODEL NO. Doing so may damage the TX-DS595.
2. Screw
1...
Owner Manual - Page 16
... PRESET MEMORY
TUNING
A SPEAKERS B
CH LEVEL
DSP/MODE ADJ
SETUP
PRESET
RETURN
PUSH TO ENTER SMART SCAN NAVIGATOR
AUDIO SELECTOR
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VCR
TAPE
FM
AM
PHONO
C D
MASTER VOLUME
BASS
TREBLE
AV RECEIVER TX-DS595
POWER
To wall outlet
SEND/LEARN indicator ON
RCVR MODE
SEND / LEARN PREPROGRAMMED & LEARNING CAPABILITY
SLEEP
ON
STDBY...
Owner Manual - Page 19
...left and right of the jog dial are lit, turning the jog dial changes the setting of the currently ...POWER ON OFF
PHONES
DISPLAY RT/PTY/TP FM MODE PRESET MEMORY
TUNING
A SPEAKERS B
CH LEVEL
DSP/MODE ADJ
SETUP
PRESET
RETURN
PUSH TO ENTER SMART SCAN NAVIGATOR
AUDIO SELECTOR
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VCR
TAPE
FM
AM
PHONO
C D
MASTER VOLUME
BASS
TREBLE
AV RECEIVER TX-DS595...
Owner Manual - Page 21
... MODE
STANDBY/ON
STANDBY POWER ON OFF
PHONES
DISPLAY RT/PTY/TP FM MODE PRESET MEMORY
TUNING
A SPEAKERS B
CH LEVEL
DSP/MODE ADJ
SETUP
PRESET
RETURN
PUSH TO ENTER SMART SCAN NAVIGATOR
AUDIO SELECTOR
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VCR
TAPE
FM
AM
PHONO
C D
MASTER VOLUME
BASS
TREBLE
AV RECEIVER TX-DS595
FM AM
One of...
Owner Manual - Page 22
...POWER ON OFF
PHONES
DISPLAY RT/PTY/TP FM MODE PRESET MEMORY
TUNING
A SPEAKERS B
CH LEVEL
DSP/MODE ADJ
SETUP
PRESET
RETURN
PUSH TO ENTER SMART SCAN NAVIGATOR
AUDIO SELECTOR
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VCR
TAPE
FM
AM
PHONO
C D
MASTER VOLUME
BASS
TREBLE
AV RECEIVER TX-DS595...Lights red)
DSP/MODE ADJ PUSH TO ENTER
MEMORY
4. Turning the jog dial, select a preset number (from 1...
Owner Manual - Page 24
... dial
STANDBY/ON
STANDBY POWER ON OFF
PHONES
DISPLAY RT/PTY/TP FM MODE PRESET MEMORY
TUNING
A SPEAKERS B
CH LEVEL
DSP/MODE ADJ
SETUP
PRESET
RETURN
PUSH TO ENTER SMART SCAN NAVIGATOR
AUDIO SELECTOR
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VCR
TAPE
FM
AM
PHONO
C D
MASTER VOLUME
BASS
TREBLE
AV RECEIVER TX-DS595
FM
Displaying Radio Text...
Owner Manual - Page 25
... simultaneously. Selecting a listening mode.
Turning the control clockwise increases the volume level...POWER ON OFF
PHONES
DISPLAY
DIMMER
FM MODE PRESET MEMORY
TUNING
A SPEAKERS B
CH LEVEL
DSP/MODE ADJ
SETUP
PRESET
RETURN
PUSH TO ENTER SMART SCAN NAVIGATOR
AUDIO SELECTOR
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VCR
TAPE
FM
AM
PHONO
C D
MASTER VOLUME
BASS
TREBLE
AV RECEIVER TX-DS595...
Owner Manual - Page 26
...
STANDBY/ON
STANDBY POWER ON OFF
PHONES
DISPLAY
DIMMER
FM MODE PRESET MEMORY
TUNING
A SPEAKERS B
CH LEVEL
DSP/MODE ADJ
SETUP
PRESET
RETURN
PUSH TO ENTER SMART SCAN NAVIGATOR
AUDIO SELECTOR
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VCR
TAPE
FM
AM
PHONO
C D
MASTER VOLUME
BASS
TREBLE
AV RECEIVER TX-DS595
SLEEP
RCVR MODE
CH SEL AUDIO
AUDIO SELECTOR
BASS...
Owner Manual - Page 32
... a vast dynamic range; The current setting appears.
4. Turn the jog dial or press the or cursor buttons on the remote controller to display "3. To exit the setup mode immediately, press the SETUP button. Power On Volume (POWERONVOL): This sets a designated volume setting for the TX-DS595 to play a movie at low volumes. PREFERENCE."
2. Press...
Owner Manual - Page 33
.../ON
STANDBY POWER ON OFF
PHONES
DISPLAY RT/PTY/TP FM MODE PRESET MEMORY
TUNING
A SPEAKERS B
CH LEVEL
DSP/MODE ADJ
SETUP
PRESET
RETURN
PUSH TO ENTER SMART SCAN NAVIGATOR
AUDIO SELECTOR
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VCR
TAPE
FM
AM
PHONO
C D
MASTER VOLUME
BASS
TREBLE
AV RECEIVER TX-DS595
Input source buttons
The TX-DS595 can be...
Owner Manual - Page 50
...Power turns on the front panel of the TX-DS595 to make sure that has better directivity and select a point
where distortion is dirty or worn, or a problem...problem. • Treble control is heard. Contact your Onkyo Service Center.
FM/AM TUNER
AM stations cannot be received...8226; Audio connection cables on FM stations. • Station is turned up an outdoor AM antenna. POWER
Power shuts ...
Owner Manual - Page 51
... is functioning in this occurs, unplug the power cord from S VIDEO OUT. The TX-DS595 contains an internal microcomputer that the signal input to S VIDEO IN is not output from the wall outlet, wait five or more seconds, and then plug it is necessary to receive the output signals from an external source or...
Similar Questions
My Onkyo Tx Ds595 Has Power And Display But It Hungs.
display only dvd .if press other buttons doesn work.even volume control level only on level 10.
display only dvd .if press other buttons doesn work.even volume control level only on level 10.
(Posted by edwinplaza278 3 years ago)
How Do I Hook Up An Onkyo Equalizer To My Onkyo Av Receiver Tx-sr600
how do I hook up my Onkyo equalizer to my Onkyo AV receiver TX-SR600
how do I hook up my Onkyo equalizer to my Onkyo AV receiver TX-SR600
(Posted by casesimmons94 3 years ago)
Onkyo Receiver Tx Ds595 In Protection Mode
As soon as I on my onkyo receiver model TX-DS 595 it gets on and in couple seconds goes on protectio...
As soon as I on my onkyo receiver model TX-DS 595 it gets on and in couple seconds goes on protectio...
(Posted by Jeff0748058149 5 years ago)
Reset En In Receptor Onkio Tx-ds595
Como hacer un reset total del receptor Onkio y recuperar los valores de fábrica de todos los it...
Como hacer un reset total del receptor Onkio y recuperar los valores de fábrica de todos los it...
(Posted by tbcmcg 6 years ago)