NordicTrack A2350 Treadmill Support Question
NordicTrack A2350 Treadmill Support Question
Find answers below for this question about NordicTrack A2350 Treadmill.Need a NordicTrack A2350 Treadmill manual? We have 2 online manuals for this item!
Question posted by chrishansengm on November 3rd, 2020
Nordictrack A2350 Motor Is Loud.
Sounds like the bearings are wearing Can it be lubricated?
Current Answers
Answer #1: Posted by Odin on November 3rd, 2020 12:50 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
Yes, it can.
Be sure to verify if you are getting the noise while you are physically on the machine or with no one on it. Creaking or squeaking while running on the machine usually indicates an issue in your incline motor, deck frame, springs, and or pivot points.
A loud grumbling noise getting louder and louder while elevating speed usually means you have a bad bearing.Any knocking noise coming from a treadmill indicates bad bearings in your front roller, rear roller, or drive motor
Isolate the bearings in the front and rear rollers from the drive motor bearings
To test: Unplug machine, remove the main shroud, remove drive belt from drive motor and front roller pulley. After doing so, move the treadmill belt by itself by pushing it backward or forward with just your hands and listen for any noise, if you get any noise it is most likely coming from either the front or rear roller. To isolate the noise out of the two rollers you must remove the rollers and turn each one individually.
If no noise with the first test, go ahead and start the machine and run it at a low speed. You want to listen for noise, if you get knocking or grumbling while drive motor is running with no drive belt attached then the issue is in your Drive Motor.
A lot of times simple maintenance will save your treadmill from noise. You want to lubricate your treadmill's *pivot points: Incline motor bolt, shaft, deck screws, and any *pivot points on the bottom of your machine. Metal-on-metal pivot points are usually the culprit. Synthetic grease works best, or any spray on lubrication works if you do not want to remove any bolts or hardware.
Be sure to verify if you are getting the noise while you are physically on the machine or with no one on it. Creaking or squeaking while running on the machine usually indicates an issue in your incline motor, deck frame, springs, and or pivot points.
A loud grumbling noise getting louder and louder while elevating speed usually means you have a bad bearing.Any knocking noise coming from a treadmill indicates bad bearings in your front roller, rear roller, or drive motor
Isolate the bearings in the front and rear rollers from the drive motor bearings
To test: Unplug machine, remove the main shroud, remove drive belt from drive motor and front roller pulley. After doing so, move the treadmill belt by itself by pushing it backward or forward with just your hands and listen for any noise, if you get any noise it is most likely coming from either the front or rear roller. To isolate the noise out of the two rollers you must remove the rollers and turn each one individually.
If no noise with the first test, go ahead and start the machine and run it at a low speed. You want to listen for noise, if you get knocking or grumbling while drive motor is running with no drive belt attached then the issue is in your Drive Motor.
A lot of times simple maintenance will save your treadmill from noise. You want to lubricate your treadmill's *pivot points: Incline motor bolt, shaft, deck screws, and any *pivot points on the bottom of your machine. Metal-on-metal pivot points are usually the culprit. Synthetic grease works best, or any spray on lubrication works if you do not want to remove any bolts or hardware.
*Pivot points are areas of high friction where there may be a bolt, washer, and nut attached to the base of your frame or any hinges on your folding type treadmills. Metal=to-metal needs to be lubricated to minimize wear and tear of those areas.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related NordicTrack A2350 Treadmill Manual Pages
English Manual - Page 1
As a manufacturer, we are damaged or missing, PLEASE DO NOT CONTACT THE STORE.
w
Visit our website at www.nordictrack.com If you have questions, or if parts are committed to providing complete customer satisfaction. Save this equipment.
For assistance, contact our Customer Service Department. ...
English Manual - Page 2
NordicTrack is a trademark of Apple Computer, Inc., registered in the U.S. TABLE OF CONTENTS
WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 ASSEMBLY 6 OPERATION AND ADJUSTMENT 12 HOW TO FOLD AND MOVE THE TREADMILL 23 TROUBLESHOOTING 25 EXERCISE GUIDELINES 28 PART LIST 30 EXPLODED DRAWING 32 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover...
English Manual - Page 3
... blocks air openings. The pulse sensor is not working properly.)
8. Do not operate the treadmill if the power cord or plug is damaged, or if the treadmill is intended only as described.
4. Wear appropriate exercise clothes when using the treadmill.
18. Do not use of serious injury, read all users of this manual and all...
English Manual - Page 4
... sure that the frame is properly assembled. (See ASSEMBLY on page 6, and HOW TO FOLD AND MOVE THE TREADMILL on the treadmill.
24.
vice representative.
Never remove the motor hood un- Servicing other than the
procedures in a commercial, rental, or institutional setting.
20. nance and adjustment procedures described in the storage position.
23...
English Manual - Page 5
...for selecting the revolutionary NordicTrack® A2350 treadmill with the parts that... are shown on the front cover of this manual.
For your workouts at home more enjoyable and effective. BEFORE YOU BEGIN
Thank you have questions after read this manual carefully before contacting us assist you ʼre not exercising, the unique treadmill...
English Manual - Page 6
...
5/16" x 1" Bolt (7)-6
3/8" x 2" Bolt (4)-3
3/8" x 4" Bolt (6)-4
6 Note: The underside of the walking belt, simply wipe off the lubricant with high-performance lubricant. If there is lubricant on top of the treadmill walking belt is completed. During shipping, a small amount of lubricant may be assembled. To avoid damaging plastic parts, do not use power tools for assembly.
Use...
English Manual - Page 10
... sleeve has been slid over the indicated hole and that the large barrel and the Latch Knob (54) are properly tightened before you use the treadmill. Raise the Frame (56) to the handrail assembly with the bracket.
Note: Extra hardware may be included. Be careful not to the Base (83) with...
English Manual - Page 12
...used it will deteriorate the walking belt and cause excessive wear. Whenever the adapter is used to connect the surge suppressor...and serious injury.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with a cord ... place by a qualified electrician. Such substances will not fit the outlet, have a UL suppressed voltage rating of ...
English Manual - Page 13
... be changed with the consoleʼs sound system while you exercise. To use the manual mode, see page 18. five weight loss workouts and five classic workouts. You can even measure your fitness age. iFit workouts automatically control the treadmill while the voice of a personal trainer coaches you and motivates you through every step...
English Manual - Page 14
...to warm to the walking platform, wear clean athletic shoes while using the treadmill.
Note: Make sure that the circuit breaker is turned on the treadmill frame near the power cord. ... TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it reaches the selected speed setting. If you exercise, change by
carefully taking a few seconds. Reset...
English Manual - Page 15
... speeds.
4. To change until the entire track is lit.
The Fitness Age Calculator display is ideal for aerobic exercise. Workout Intensity Level Bar
To reset the displays, press the Stop ...15 As you exercise, the indicators around the track will gradually change the incline of the treadmill, press the Incline increase and decrease buttons or one of the treadmill as desired....
English Manual - Page 16
... are clean.
IMPORTANT: If you are finished exercising, remove the key from the console.
Before ...put it in the right side of the treadmill to hold the metal contacts on the handrail...this, the treadmillʼs electrical components may damage the treadmill. You can measure your...using the treadmill, switch the...treadmill to the "off" position and unplug the power cord. When you may...
English Manual - Page 17
...treadmill will appear in the display for the next segment.
4. Monitor your heart rate if desired. Hold the handrails and begin to flash. Current Segment
5. See step 7 on page 16.
6. Insert the key into one incline setting are finished exercising... speed and incline settings for each segment, a series of tones will sound and the next segment of the workout. Each preset workout is too ...
English Manual - Page 18
...Workout button. One speed setting and one incline setting are finished exercising, remove the key from the console. To stop . The ...Start Workout button. At the end of the workout begins, the treadmill will begin walking. The walking belt will not start the workout.... in the display for each segment, a series of
tones will sound and the next segment of the profile repre-
6.
If the ...
English Manual - Page 19
... sensor or wear the optional chest pulse sensor to select your age. See page 22 for at least two hours, and when you have not entered your height, press the Set Height increase or decrease button repeatedly to enter your height. If you have not exercised for more information on the treadmill. If...
English Manual - Page 20
... iPod near the speaker. Make sure that the iFit Universal iPod Connector is fully plugged in the Fitness Age Calculator display.
5. Make sure that the audio wire is fully inserted.
See step 5 on...and the other end into your iPod. If you are finished exercising, remove the key from the console. HOW TO USE THE SOUND SYSTEM
This product has been designed specifically to work with the display...
English Manual - Page 21
... start the workout.
1.
Each iFit workout is oriented so the metal contacts are face-down and are finished exercising, remove the key from the iFit slot when you press the Start button, the treadmill will begin walking.
2.
Next, select an iFit workout by pressing the Speed or Incline buttons; To restart the...
English Manual - Page 30
...1 1/4" Bolt Rear Roller Bolt 3/8" x 1 3/4" Bolt 3/8" x 1 1/2" Bolt 3/8" x 1" Bolt 1/2" Ground Screw #12 x 1 Screw Motor Bolt Cushion Stop Reset/Off Circuit Breaker Belt Guide Screw 1/4" Flat Washer 1/4" Lock Washer Frame/Roller Ground Wire 5/16" Cage Nut #8 x 1 3/4"... Left Rear Foot Right Rear Foot Hood Drive Belt Motor Isolator Motor Lift Frame Wire Tie Controller Ground Wire Power Cord Power ...
English Manual - Page 31
... 2 106 1 107 2 108 8 109 2
Description
Pulse Bar Ground Wire Latch Endcap iFit Card Kit Lift Motor Spacer #8 x 2" Screw Right Handrail Trim #8 Star Washer #8 x 5/8" Screw 3/8" Jamnut Nut
Key No. Key No. Description
French Warning Decal Incline Motor Wire Key Switch Console Warning Decal 4" White Wire, M/F Userʼs Manual
*These parts are subject to...
English Manual - Page 36
...terms set forth above is in connection with respect to any implied warranties of merchantability or fitness for a particular purpose are warranted for a lifetime. This warranty does not extend to... warranty is not responsible or liable for commercial or rental purposes; The frame and drive motor are made must be free from province to province. ICON is limited to repairing or replacing...
Similar Questions
After Recalibrating And Key Is Removed The Treadmill Sounds Like Its On.
The incline feature on my NordicTrack T5.7 stopped working. I followed the instructions in the manua...
The incline feature on my NordicTrack T5.7 stopped working. I followed the instructions in the manua...
(Posted by jjaniec 3 years ago)
Nordictrack Treadmill A2155
Hi my nordictrack treadmill a 2155 is been working for a very long time and now I am having a proble...
Hi my nordictrack treadmill a 2155 is been working for a very long time and now I am having a proble...
(Posted by albagodiva 4 years ago)
I Have A Nordictrack A2350 Treadmill With Belt Issues
My nordictrack was having issues declining and inclining recently and then the belt stopped in the m...
My nordictrack was having issues declining and inclining recently and then the belt stopped in the m...
(Posted by ralston51 8 years ago)
A2350
key came off during operation and now doesn't want to start
key came off during operation and now doesn't want to start
(Posted by rbustamantelaw 9 years ago)
Nordictrack A2350 Fitness Age Calculator Display Not Working
(Posted by pnoicegl 10 years ago)