Maytag MVWC450XW Support Question
Maytag MVWC450XW Support Question
Find answers below for this question about Maytag MVWC450XW.Need a Maytag MVWC450XW manual? We have 3 online manuals for this item!
Question posted by tlwells985 on July 17th, 2016
It Want Do Nothing
the door locks but it just don't do nothing
Current Answers
Answer #1: Posted by Odin on July 17th, 2016 4:33 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,700
Member since:
April 10th, 2010 Points: 41,236,700
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Maytag MVWC450XW Manual Pages
Installation Instructions - Page 2
... or measuring tape
Pliers that open to toll-free numbers on back page of your washer in the top of your Use and Care Guide.
Install your Use and Care Guide... 367031 Connector Kit Part Number 285835
LOCATION REQUIREMENTS
Select proper location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 mm) (686 mm)
42" (1067 mm)
2...
Installation Instructions - Page 3
... mm)
17" (432 mm)
48 in.2 (310 cm2)
See requirements for closet door ventilation openings which are required. If a closet door or louvered door is not recommended. Top of 1" (25 mm) under entire washer. Secure drain hose with maximum slope of laundry tub must be exposed to reduce noise transfer. n A grounded electrical outlet located within...
Installation Instructions - Page 4
... separate circuit breaker serving only this time.
4 NOTE: To avoid floor damage, set washer onto cardboard before moving it and make sure lid is the personal responsibility and obligation of...shipping materials It is necessary for proper operation and to remove all shipping materials for proper operation. Move washer
n A 120 volt, 60 Hz., AC only, 15-
If a mating outlet is not available...
Installation Instructions - Page 5
... console to allow free access to free from tub. Attach drain hose to remove all parts from tub
Connect Drain Hose
5. For a laundry tub or standpipe drain, go to move washer later.
4.
do not force excess hose into standpipe (shown in case you need additional parts with clamp. NOTE: Keep tray in...
Installation Instructions - Page 6
... hose installation or replacement dates for a few seconds through hoses into a laundry tub, drainpipe, or bucket to tighten couplings an additional two-thirds turn .
See "Tools and Parts". Connect inlet hoses to washer
Attach hose to check for leaks
Turn on washer.
Use pliers to water faucets with new inlet hoses with flat...
Installation Instructions - Page 7
... a wood block or similar object that will support weight of washer
Place level here
Place level here
If washer is level, skip to reduce excess noise and vibration.
13. Level Washer
IMPORTANT: Level washer properly to step 14. HELPFUL TIP: You may want to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with...
Installation Instructions - Page 8
.... If there is plugged into a grounded 3 prong outlet
Complete Installation CHECKLIST
q Check electrical requirements.
q To test and clean your Washer User Instructions. q Check that all packaging materials. q Read "Washer Use" in your washer, measure 1/2 of normal
recommended amount of /recycle all parts are on. q Check that yellow shipping materials were completely
removed from...
Dimension Guide - Page 1
... minimum required. This washer has been tested for closet door ventilation openings which are required. Minimum capacity: 20 gal. (76 L).
W10240509C 02/2011 A time-delay fuse or circuit breaker is required. For closet installation, with spacing of laundry tub must install higher than 4.5" (114 mm) of drain hose should be provided. Add spacing...
Warranty Information - Page 1
MAYTAG® LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or ...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Sounds different than my previous washer- Front-load washer
... pulled through increasingly higher spin speeds. The sounds recorded below give examples of the door locking and unlocking. (8 seconds, 130 KB) Water will hear sounds that you are part of a washer tumbling a load. wet loads - Front-load washer Washer not draining, not spinning out water; is this normal? As water drains from the... -
The door will not open - Front-load washer
... to stop spinning and draining before the door will not start - Front-load washer Washer will unlock. Front-load washer The door should unlock at the same point where it unlocks. The door will not open . Front-load washer The door to remove any remaining water from the washer. Is the door locked and the Add A Garment or... -
How do I clean my Epic® or Neptune® front-load washer?
... water. Select the highest spin speed available. Select the additional or 2nd Rinse option (if available). The door will lock and filling will stop the cycle. Do not add any clothing or items from the washer. If the procedure does not sufficiently improve the machine freshness, please evaluate your Use and Care...
Similar Questions
Maytag Washer Mhw7000 With Door Locked. How To Manually Unlock The Door
Is there a way to manually unlock the door otherwise I have to wait for a repair person for 14 days?...
Is there a way to manually unlock the door otherwise I have to wait for a repair person for 14 days?...
(Posted by varobertson 9 years ago)
'lid Lock' Light Flashes
When tub is out of balance, the lid lock light flashes and washer will not advance until unpluged.
When tub is out of balance, the lid lock light flashes and washer will not advance until unpluged.
(Posted by ds3497 10 years ago)
Washer Will Not Stay On
The washer will start the cycle when button is depressed for 3 seconds. It will begin to spin, but t...
The washer will start the cycle when button is depressed for 3 seconds. It will begin to spin, but t...
(Posted by dlbarto 10 years ago)
