Home » Maytag » Laundry Washers » Maytag MVWC450XW

Maytag MVWC450XW Support Question

Find answers below for this question about Maytag MVWC450XW.
Need a Maytag MVWC450XW manual? We have 3 online manuals for this item!

Maytag Overview Questions Manuals Reviews Videos Research

Question posted by dlbarto on December 15th, 2013

Washer Will Not Stay On

The washer will start the cycle when button is depressed for 3 seconds. It will begin to spin, but then shut off within 5-10 seconds.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Maytag MVWC450XW Manual Pages

Installation Instructions - Page 2

...parts before starting installation. Tools needed: Parts needed: (Not supplied with washer) Adjustable or...diameter to toll-free phone numbers on back page of the washer. n 8212656RP n 8212641RP n 8212646RP n 8212545RP n 8212487RP n 8212638RP n 8212637RP 10 ft. (3.0 m) Inlet hose, Black EPDM (2 pack)...insert in the top of your washer in a basement, laundry room, closet, or recessed ...

Installation Instructions - Page 3

...Hose (Part Number 285863) that may be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. install no higher than 4.5" (113 mm) of hot and cold water fill valves on the ... door is not recommended. Top of laundry tub must support washer's total weight (with spacing of 0" (0 mm) clearance on washer, and water pressure of washer to weather or in low temperatures....

Installation Instructions - Page 4

... electrician. Set washer upright. n Check with a power supply cord having a 3 prong grounding plug. A time-delay fuse or circuit breaker is equipped with a qualified electrician if you start: remove shipping ... sure the washer is properly grounded. Tip washer back and place on floor behind washer. If a mating outlet is not available, it and make sure lid is taped shut. 2. or...

Installation Instructions - Page 5

...packing tray from tub. You may need to free from tray. IMPORTANT: 4.5" (113 mm) of laundry tub. 3. NOTE: Keep tray in picture) or over end as shown in standpipe Drain hose form...plug and pull to move washer later. 4. For a laundry tub or standpipe drain, go to remove all parts from rear panel. Squeeze clamp with pliers and slide black elbow end of laundry tub. See "Tools and...

Installation Instructions - Page 6

...Attach hot water hose to water faucets with new inlet hoses with second hose for a few seconds through hoses into a laundry tub, drainpipe, or bucket to check for future reference. n Periodically...step with flat washers (not provided). Check for leaks Turn on coupling by hand until clear. 10. Connect inlet hoses to washer Attach hose to faucets or washer. Screw coupling...

Installation Instructions - Page 7

... level, use a 9/16" or 14 mm open -end or adjustable wrench to check levelness of washer. Recheck levelness of washer. 15. Then turn jam nuts counterclockwise on leveling feet tightly against washer cabinet. Rock washer back and forth to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with a wood block or similar...

Installation Instructions - Page 8

... of powdered or liquid detergent and pour it into washer basket or detergent dispenser (on washer. Select any tape remaining on some models). q Check that yellow shipping materials were completely removed from console and any cycle. Start washer and allow to see what was skipped. q Read "Washer Use" in your tools. Plug into a grounded 3 prong outlet...

Dimension Guide - Page 1

... openings which are required. install no higher than 96" (2.44 m) from bottom of 0" (0 mm) clearance on all sides of washer. Ref. Top of washer. install no higher than 96" (2.44 m) from bottom of laundry tub must be provided. Louvered doors with equivalent air ventilation openings are for floor standpipe drain system. Minimum carry...

Warranty Information - Page 1

... correct the installation of your major appliance is located in accordance with Maytag published installation instructions. 10. If outside the 50 United States and Canada, contact your home. 7. You will pay ... to province. In Canada, call 18006889900. MAYTAG® LAUNDRY WARRANTY LIMITED WARRANTY For one year from the date of purchase, when this major appliance is...

Maytag Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

Washer will not fill - Front-load Epic® washer
...Is Control Locked status light on the washer clogged? Wait for 3 seconds. it will not fill. Straighten the ...Cycle End Signal button for the door to completely open both faucets for leaks. Make sure the washer is a low-water-usage washer...Select the Normal cycle and press Start. Make sure to unlock. The water level will fill from the washer. Some models ...
My load-sensing Energy Star top-load washer with agitator is using too much water.
...spray rinse technology. If your household water pressure low? Opening the lid, after the washer started to fill or during the cycle, sends a signal to the control that you may have the benefits of newly... is too low to add more laundry, add detergent, catch water for any amount of water and energy savings. Is your water pressure is less than 10 psi, the auto load sensing will...
The cycle time is not correct - Top-load HE washer with Dispensers in Corners
... cold water. Press Start. Do not add detergent. Consider adding more about unbalanced loads. The cycle time is not able to spin out water. Out of excessive suds or unbalanced load, the Estimated Time Remaining on : detergent type, size and type of the cycle. Does this time, the washer pauses the wash action...