Maytag MEDE300VF Support Question
Maytag MEDE300VF Support Question
Find answers below for this question about Maytag MEDE300VF - Performance Series Front Load Electric Dryer.Need a Maytag MEDE300VF manual? We have 1 online manual for this item!
Question posted by wmahoney on August 23rd, 2010
Dryer Won't Start We Have Power It's Brand New.
when i press start it beeps that is all
Current Answers
Related Maytag MEDE300VF Manual Pages
Use and Care Guide - Page 4
...your machines, you purchased your PERFORMANCE SERIES dryer? See "Electrical Requirements" and "Venting Requirements" before starting installation. Ask for a total height of the dryer for Part Number 8212640. ...pedestal at least 3.5" (8.9 cm) above the floor. Ask for
installing new exhaust vent) „ Tin snips (new vent installations) „ ¼" nut driver (recommended) „ ...
Use and Care Guide - Page 5
... will need 18" (46 cm) to do not permit, installation of the dryer in the top and bottom of 1" (2.5 cm) under entire dryer. If using a power supply cord, a grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer.
This dryer has been tested for proper exhaust installation.
Failure to the bottom of...
Use and Care Guide - Page 7
..." (68.6 cm)
1" (2.5 cm)
*Required spacing
Mobile home - The National Electric Code requires a 4-wire power supply connection for homes built after 1996, and all local codes and ordinances. If the dryer is adequate and in remodeling after 1996, dryer circuits involved in conformance with a 4-wire electrical supply connection, the neutral ground conductor must be at least...
Use and Care Guide - Page 8
... listed strain relief. Do not modify the plug on the dryer. Use a UL listed power supply cord kit marked for electric current.
If your outlet looks like this :
3-wire receptacle (10-30R)
Then choose a 3-wire power supply cord with flexible metallic conduit. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must be grounded...
Use and Care Guide - Page 9
... INSTRUCTIONS
4-wire receptacle 14-30R
„ Do not use Power Supply Cord Replacement Part Number 9831317. Electrical Shock Hazard
Plug into a standard 14-30R wall receptacle.
grounding conductor can result in a risk of dryer's final location.
GROUNDING INSTRUCTIONS
■ For a grounded, cord-connected dryer: This dryer must be plugged into an appropriate outlet that is...
Use and Care Guide - Page 10
...to remaining 2 terminals (gold). Securely tighten all electrical connections. Use a UL listed strain relief.
Disconnect power before making electrical connections.
Connect remaining 2 supply wires to center ... to green ground connector.
Disconnect power. 2.
C
A. Only
Direct Wire
WARNING
WARNING
Fire Hazard
Use a new UL listed 30 amp power supply cord.
Strain relief tab pointing...
Use and Care Guide - Page 11
... for your type of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is inside the terminal block opening, screw the removable conduit connector onto the strain relief threads. The strain relief should have a tight fit with the dryer cabinet and be connecting to:
A UL listed, 120/240volt minimum, 30-amp, dryer power supply cord*
Go...
Use and Care Guide - Page 12
...
5. Direct wire cable must have completed your electrical connection. Ground prong D. Ring terminals
1.
Tighten screw. Ground wire (green or bare) of power supply cord under center, silver-colored terminal block...wires to center silvercolored terminal block screw. Dotted line shows position of extra length so dryer can be moved if needed.
12 down screw. 7. Now go to external ground...
Use and Care Guide - Page 13
... screw - B. Strip 5" (12.7 cm) of outer covering from end of power supply cable C. ¾" (1.9 cm) UL listed strain relief D. A
D
...ground wire D.
B
A C
A. A. Shape ends of dryer rear panel. Connect neutral
ground wire and place the hooked end...Tighten strain relief screw.
6. You have completed your electrical connection. Dotted line shows position of
the terminal block...
Use and Care Guide - Page 14
... hooked end together and tighten screw, as shown. Direct wire cable must have completed your electrical connection. If using 3-wire cable with ground wire, cut bare wire even with up turned ends...) of outer covering from end of extra length so dryer can be moved if needed. Connect neutral wire (white or center wire) of power supply cord to outer terminal block screws. Neutral (white...
Use and Care Guide - Page 15
...tab of terminal block cover into slot of dryer rear panel.
C A
B
D
E
Optional 3-wire connection
Use for direct wire or power supply cord where local codes do not ...permit connecting cabinet-ground conductor to "Venting Requirements." Tighten screw. Center silver-colored terminal block screw
D. You have completed your electrical connection....
Use and Care Guide - Page 16
...132; For best drying performance, rigid metal vents are acceptable only if accessible for cleaning. „ Flexible metal vent must be fully extended and supported when the dryer is not plugged
with ...Flexible metal vent „ Flexible metal vents are recommended. „ Rigid metal vent is a new vent system
Vent material „ Use a heavy metal vent. Elbows 45° elbows provide better...
Use and Care Guide - Page 20
... or tape remaining on power.
7.
NOTE: You may be a problem with a 4" (10.2 cm) clamp.
2. The odor will not start of your home power supply keeping the dryer's heater from turning on...the dryer is made, remove the corner posts and cardboard. Check the dryer's final location. Move dryer into a grounded outlet and/or electrical supply is secured to adjust the legs up the dryer using...
Use and Care Guide - Page 21
... cooking oils). This manual covers several different models. Press the POWER/CANCEL button then rotate the dial to each load. Failure to persons, read the IMPORTANT SAFETY INSTRUCTIONS ...electric shock, or injury to follow these instructions can completely remove oil. Failure to starting your dryer. WARNING: To reduce the risk of oil on a clothesline or by using an Air Cycle. Place laundry...
Use and Care Guide - Page 22
.... If you want the load to be changed only with the cycle or option combinations selected.
„ Press POWER/CANCEL.
„ Rotate the dial to select a Timed Cycle.
„ Press the TIME ADJUST up or down buttons until the desired temperature glows yellow.
Press and hold START/PAUSE button until dryer starts (about 1 second). Pressing the SENSOR CYCLE DRYNESS...
Use and Care Guide - Page 23
... choose a different dryness level, depending on , the dryer can be restarted until dryer starts. To enable the Control Lock feature when dryer is off . The control is locked when a single beep is heard and the Control Lock light is on the load size and dryness level. To unlock: Press and hold the CONTROL LOCK button for a guide...
Use and Care Guide - Page 25
...load to help smooth out wrinkles from the dryer as soon as it will vary depending on the cycle selection knob.
25 Press POWER/CANCEL. It is not necessary to make a selection on load type and load... is pressed again, the door is an automatic cycle. Press DRUM LIGHT at any time to turn on the light inside the dryer drum.
Timed Cycles
Use Timed Cycles to start. Press START/PAUSE to...
Use and Care Guide - Page 26
... after pressing Start You can change a Modifier or Option anytime before pressing Start. Press START/PAUSE once. Press and hold START/PAUSE to secure over the edge of your dryer. The dryer starts at the end of the new cycle. Changing Modifiers and Options after pressing Start 1. Press START/PAUSE once. 2. Select the new Modifier and/or Option. 3. Press and hold START/PAUSE...
Use and Care Guide - Page 28
... and secure with powdered laundry detergent and very warm water. 2. Cleaning the Dryer Interior
To clean dryer drum 1. Make a paste with the screw.
4.
If you are secure in dryer base. 3.
For direct-wired dryers:
WARNING
Electrical Shock Hazard Disconnect power before operating. Use masking tape to your dryer only when you will not stain future loads of time, you...
Use and Care Guide - Page 29
...dryer. Electric dryers use two household fuses or breakers. If the dryer hasn't been used ? See the Installation Instructions.
„ Is the clothing knotted or balled up , the load... the dryer. otherwise, press POWER/CANCEL and then start a new cycle.
„ "L2" Diagnostic Code (low or no line voltage condition): The drum will continue to "Electrical Connection" for details. Press any ...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
My dishwasher will not start
...the door is opened while running a cycle. Check your household electrical box to the dishwasher? To cancel the delay and cycle, press Start/Cancel twice. Is the control lock option activated? Instructions are ... on top of the cycle. Opening the door or interrupting the power can cause my dishwasher to not start? Make sure the door is completely closed and latched. On ... -
How do I open the lid?- Top-Load HE with Dispenser Drawer
or Are you using the washer for first time? Press the Power button to turn the washer off . Top-load washer with Dispenser Drawer How do I open the lid of my Bravos washer? Front-load washer Vibration - The lid will reset the lock. Press Start/Pause/Unlock again to open - Under certain conditions, the... -
The fabric softener dispenser is not working correctly - Top-load HE washer with Dispenser Drawer - video
...measured liquid fabric softener into the dispenser before starting the washer. The following video demonstrates how the dispenser operates. Do not add powdered laundry products to the fabric softener dispenser. ...button. See the Use and Care Guide for details. Top-load HE washer with warm water to ensure best performance. Is water left in the rinse cycle. A small amount of...
Similar Questions
Lint Light Will Not Clear On Brand New Gas Dryer
Lint light will not clear on brand new gas dryer
Lint light will not clear on brand new gas dryer
(Posted by cindylafond 7 years ago)
On My Maytag Dryer Mede300vf I Have Water In The Vent. Why?
where can this water be coming from.
where can this water be coming from.
(Posted by jimmielighter 9 years ago)
How To Reverse The Door On A Maytag Performance Series Front Load Dryer Model
number mede300vf0
number mede300vf0
(Posted by jacqjeepu 9 years ago)
Super Noisy Dryer Brand New
Are these dryers super noisy. Brand new used once
Are these dryers super noisy. Brand new used once
(Posted by abackor 11 years ago)