Lexmark X264dn Support Question
Lexmark X264dn Support Question
Find answers below for this question about Lexmark X264dn.Need a Lexmark X264dn manual? We have 8 online manuals for this item!
Question posted by ccarSabre on December 20th, 2013
How To Clear Replace Pc Kit X264dn
The person who posted this question about this Lexmark product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Lexmark X264dn Manual Pages
User's Guide - Page 153
... by aligning the rollers on the toner cartridge with the arrows on the display. You can also see the status of the photoconductor kit by showing 84 PC Kit life warning or 84 Replace PC Kit on the tracks of -life, print quality significantly decreases. While the printer may continue to function properly after the photoconductor...
User's Guide - Page 182
...a properly grounded outlet. 5 Turn the printer back on.
84 PC Kit life warning
The photoconductor kit is not set to Disabled.
to clear the message and continue printing.
58 Too many trays attached
1 Turn...options installed
Try one or more of the following:
• Replace the photoconductor kit. • Press to clear the message and continue printing.
to continue printing.
56 Standard ...
User's Guide - Page 183
Install a new photoconductor kit.
88.yy Cartridge is low
Replace the toner cartridge, and then press to clear the message and continue printing.
200....to continue printing.
202.yy Paper jam
The message indicates either where the paper is exhausted. Troubleshooting
183
84 Replace PC Kit
The photoconductor kit is jammed or the number of pages jammed.
1 Open the front door. 2 Open the rear door. ...
User's Guide - Page 185
Note: The message clears when the pages are removed from the ADF.
2 Flex and fan the pages. 3 Place the pages in the ... following: • Remove Tray 1. • Open the front door, and then remove the photoconductor kit and toner cartridge. • Remove Tray 2.
2 Remove the jam. 3 Replace the photoconductor kit and toner cartridge if you removed them. 4 Close any open doors or trays. 5 Press to...
User's Guide - Page 207
... reduce the risk of the printer might be hot. THE TONER CARTRIDGE IS DEFECTIVE
Replace the toner cartridge.
Clear any paper you are possible solutions. MAKE SURE THE PAPER PATH IS CLEAR
Paper could be caught between the photoconductor kit and the fuser.
To reduce the risk of the following:
THE TONER MAY SMEAR...
User's Guide - Page 228
... 58 Too many flash options installed 182 58 Too many trays attached 182 84 PC Kit life warning 182 84 Replace PC Kit 183 840.01 Scanner Disabled 186 840.02 Scanner Auto Disabled 186 88.yy ...stock loading 46 tips 65 checking an unresponsive printer 176 checking an unresponsive scanner 192 checking device status on Embedded Web Server 158
cleaning ADF separator rollers 147 exterior of the printer 146...
User's Guide - Page 232
... 182 58 Too many flash options
installed 182 58 Too many trays attached 182 84 PC Kit life warning 182 84 Replace PC Kit 183 840.01 Scanner Disabled 186 840.02 Scanner Auto
Disabled 186 88.yy Cartridge...
Scanner ADF Cover Open 179 Scanner Jam Access Cover
Open 179 Toner is low 179 Unsupported USB device, please
remove 179 Unsupported USB hub, please
remove 180 USB/USB 180 Waiting 180 Waiting for ...
User's Guide - Page 233
...ordering ADF pick assembly 151 ADF separator roll 151 photoconductor kit 150 toner cartridges 150 supply notifications configuring 159
T
... labels, paper 64 letterhead 62 transparencies 63 toner cartridge replacing 151 toner cartridges ordering 150 recycling 38
Toner is low...197 troubleshooting, paper feed
message remains after jam is cleared 199
page that jammed does not reprint 199
troubleshooting...
Maintenance Guide - Page 10
... rollers on the toner cartridge with the arrows on the display. When 84 PC Kit life warning or 84 Replace PC Kit first appears, you before the photoconductor kit reaches a page maximum by showing 84 PC Kit life warning or 84 Replace PC Kit on the tracks of the
photoconductor kit. Push the toner cartridge in as far as it will go.
Service Manual - Page 33
...MMR MPF MR MROM MS NAND NVM NVRAM OCF OCR OEM OHP OPC OPT PC PDF PICS PIN
Gigabyte Ground Fault Interrupter Gigahertz Host Based Printing High-capacity ...Laser Scanning Unit Low Voltage Low voltage power supply Magenta Megabyte Motor Driver Control Multifunction Device Multifunction Printer Message handling Motor interface Millimeter Modified modified read Multipurpose feeder Modem ready Masked ...
Service Manual - Page 44
... Warning Replace the PC kit to ensure print quality.
84 Replace PC Kit 88 Cartridge Low
This warning is displayed when the cartridge is reset or menus are entered. 7013-XXX
User status and attendance messages (continued)
User primary message
Explanation
56 Standard USB Port Disabled
This message may be taken:
• Press Select ( ) to clear the...
Service Manual - Page 45
... too loose.
200.06 Imaged page not expected page (bouncy passthru sensor)
Remove the toner cartridge/PC kit. Possible causes include bouncy sensor or exceptionally fast pick- If so, then inspect the tray wear strips and replace if necessary.
It should rotate freely. See "Media manual input sensor removal" on page 3-15) will...
Service Manual - Page 46
... size (length) problem, pre-staged media in the tray, and replace if they are worn.
200.26 The trailing edge never cleared the input sensor when feeding out the media that the media is too...notice if the leading edge of the PC kit for debris in the tray, and replace if they are a small gap or a bouncy manual feed sensor. Remove the toner cartridge/PC kit and inspect the input sensor flag....
Service Manual - Page 47
...The media is that the pick tires are worn.
200.33 200.34
Page from tray 1 to clear the paper path.
"Printhead service check" on page 2-43.
Possible cause is at the alignment gate... but
Verify that the narrow media flag rotates freely and securely. Replace the pick tires if necessary. Remove the toner cartridge/PC kit and check for any page(s) ahead to reach the input sensor ...
Service Manual - Page 48
... than intended
Remove the toner cartridge/PC kit and check for damage at the .... If the flag does not rotate freely or has no spring action, then replace the fuser.
Check the paper setting and correct if needed. Indicates code may...during warm-up.
202.26 Trailing edge never cleared exit sensor when feeding out media that the jam was never cleared. Note: Print a page with sensor and ...
Service Manual - Page 70
... to isolate problems such as light or toner streaks.
Blank pages can be ground except for cartridge damage. Try a different toner cartridge and PC kit.
• If those fail, then replace the LVPS/HVPS, controller board, or the printhead in printer service errors unless there is blank.
2. b. e. To exit configuration, turn the printer...
Service Manual - Page 71
...check ground paths. • Check continuity in the cable. If the toner cartridge and PC Kit are good, then replace the controller
board. • See the "LVPS/HVPS service check" on page 2-29...the next level of the photoconductor causes an all black page.
FRU Toner cartridge (not a FRU) PC Kit (not a FRU)
LVPS/HVPS Controller board
Action
Check the toner darkness setting in the order shown:
...
Service Manual - Page 72
... setting to evenly distribute the toner. If toner cartridge is being used . Try a new PC Kit. Replace as necessary. Make sure recommended media is low, then try a new one. Check the springs...and right transfer roll bearings. Check the media settings in image density horizontally across page
FRU PC Kit (not a FRU)
Transfer roll
Action
The charge roll may not be operating at its ...
Service Manual - Page 73
... roller.
None of these voltages can be measured, but the contacts and continuities can cause excessive toner to the back of pages. Recheck condition before replacing PC Kit, if necessary. Verify the high voltage cable is not low on a page with a soft cloth. It may also be checked. Toner on the wiring diagram...
Service Manual - Page 74
... laser beam, which may be full. The PC cleaner sump may be partially blocked. Replace the PC kit.
2-40 Service Manual
Blurred characters
Blurred images, including characters, are parallel and match the two intended ghost images, then the Form Type may be defective.
With the printer off , clear the path or clean the lens.
With...
Similar Questions
What Does It Mean When The Printer Says, ' Replace Pc Kit'
(Posted by vickiegrant 12 years ago)
Replace Pc Kit
Our printeer is reading replace pc kit. What doea this mean?
Our printeer is reading replace pc kit. What doea this mean?
(Posted by ajackson4780 12 years ago)