Home » Kyocera » Multifunction Devices » Kyocera TASKalfa 250ci

Kyocera TASKalfa 250ci Support Question

Find answers below for this question about Kyocera TASKalfa 250ci.
Need a Kyocera TASKalfa 250ci manual? We have 24 online manuals for this item!

Kyocera Overview Questions Manuals Reviews Videos Research

Question posted by info20486 on September 20th, 2013

C5101 Error Code

I have a c5101 error code. How do I clear it?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TommyKervz on September 21st, 2013 12:22 AM

This answer was accepted by the poster of the original question.

TommyKervz

Member since:
January 10th, 2013

Points: 17,776,843

1,100
points

Greetings. The book says "Incorrect Vpp values during initialization" and "Replace Black Primary Charge Assy.

http://www.copytechnet.com/forums/kyocera-mita-copystar/50812-heads-up-voyagere.html

Hope that is helpful.
Kervz at www.satechhelp.co.za

Related Kyocera TASKalfa 250ci Manual Pages

PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 407

... printing a, 105 Font mode, 119 Fuser mode, 162, 163 G Graphics state, 228, 272 Gray pattern, 122 Grouping, 27 H Hard disk, 141, 246, 250, 256, 258 error codes, 136 I Image model, 299 International characters, 129 J Job, 136, 138, 140 printing a list of, 134 printing jobs, 136 printing with different finishing options, 138 starting...

Kyocera Command Center Operation Guide Rev 6.3 - Page 15

... displayed when the machine's Start key is enabled and the printing speed increases. COMMAND CENTER Pages Error Clear Timer Specifies the time between 5 and 495 seconds after which prompts you to confirm the destination...by time of the print system memory as the default paper source, this code, comprised of four digits from 1 to the print system operation guide. Additional Information You can ...

PRESCRIBE Commands Technical Reference Manual - Rev. 4.7 - Page 215

The error code is converted to 0.025 mm on both the x- OH [Output Hard-clip limits] This...as follows: 40, 40 TERM This response indicates that plotter units are ASCII-coded in the following format: XLL, YLL, XUR, YUR TERM LL: lower left UR: upper right 7-103 Error Number Description 0 No error 1 Instruction not recognized 2 Wrong number of parameters 3 Illegal parameter 4 (...

PRESCRIBE Commands Technical Reference Manual - Rev. 4.7 - Page 251

KPDL Operators keys to the CollateDetails parameter should have the following integer values depending on the mode of the following error codes will appear if errors occur and doautocontinue is set to the computer. KPDL Error Messages Code Error Meaning 00 Cannot initiate KPDL 01 dictfull Dictionary full; Press ON LINE Any of each e-MPS function. These...

250ci/300ci/400ci/500ci/552ci Operation Guide Rev-1 - Page 346

... machine, unplug the power cord, and contact your Service Representative. The job is canceled. note of the scanned pages - Hard Disk error. - the job separator exceeded? Only one copy of the error code displayed on the hard - Press [End]. password. Cannot print any more. separator. Remove paper from the FAX box. Name or...

250ci/300ci/400ci/500ci/552ci Operation Guide Rev-1 - Page 347

... 9-8 the waste toner box. Are there any originals left in Remove originals from the document processor, put them again. processor. Press [Continue] to Send Error for the error code and corrective actions. 10-11 Set the waste toner - Leave the machine on the touch panel. The process cannot be performed due - the document...

250ci/300ci/400ci/500ci/552ci Operation Guide Rev-1 - Page 349

.... - Folder share permissions of the recipient Check the SMB settings. - Troubleshooting Responding to send the e-mail. Error Code 1101 1102 1103 Error Message Corrective Actions Reference Page Failed to Send Error When an error occurs during transmission, Send Error appears. Failed to send the e-mail. Failed to send via FTP. Failed to send i-FAX. Failed to...

250ci/300ci/400ci/500ci/552ci Operation Guide Rev-1 - Page 350

... the network and SMB settings. The hub is connected. - Failed to send the e-mail. The network cable is not operating properly. - Troubleshooting Error Code 1104 1105 1106 1131 1132 2101 Error Message Corrective Actions Reference Page Failed to send i-FAX. Failed to send via SMB. Failed to send via FTP. Select [On] of...

250ci/300ci/400ci/500ci/552ci Operation Guide Rev-1 - Page 351

... main power switch off and - acceptable number of pages of the FTP - Is FTP available? - The server is not operating properly. method of the displayed error code and contact your service representative. - back on the COMMAND CENTER. 2-18 Check the authentication methods of the SMTP settings on . Send the excess pages separately...

250ci/300ci/400ci/500ci/552ci Operation Guide Rev-1 - Page 352

... touch panel when [Status/Job Cancel] is not indicated on the operation panel. Check the domain name. Symptom Cannot send fax. If the error code starts with the server. or Permitted ID No. Check error codes in the TX/RX Result Report and Activity Report. Is the destination FAX line busy? Is there an...

500ci/400ci/300ci/250ci Operation Guide Rev-1 - Page 390

... exceeded the - note of paper. disk. capacity exceeded for the document finisher tray? finisher tray. Press [End]. ## An error has occurred on the hard disk to cancel printing, sending or storing. of the error code displayed on the hard disk to press [Continue]. Turn off the machine, unplug the power cord, and contact...

500ci/400ci/300ci/250ci Operation Guide Rev-1 - Page 391

... and follow the instruction to cancel the job. 2-30 Replace the waste - Press [Continue] to Send Error for the error code and corrective actions. 10-11 If a staple jam occurs, the machine - System error has occurred. An error has occurred during transmission.Refer to Responding to print, send or store the scanned pages. Remove all...

500ci/400ci/300ci/250ci Operation Guide Rev-1 - Page 393

... to send via FTP. Check the host name or IP address of the recipient Check the SMB settings. - Folder share permissions of FTP. Check the error code and error message below, and follow the corresponding corrective actions. Failed to send via FTP. Check the SMB settings. - Path 3-33 Check the followings on the...

500ci/400ci/300ci/250ci Operation Guide Rev-1 - Page 394

.... The network cable is not operating properly. - The server is connected. - SMTP server name Check the followings of the POP3 user - Troubleshooting Error Code 1105 1106 1131 1132 2101 2102 Error Message Corrective Actions Reference Page Failed to send via SMB. Failed to send via FTP. Failed to send the e-mail. The hub...

500ci/400ci/300ci/250ci Operation Guide Rev-1 - Page 396

... modular cord correctly. and "Registering Permit ID No." Contact your Service - Check Permitted FAX No. FAX System (Q) Operation Guide Chapter 6 "Registering Permit FAX No." Check error codes in the TX/RX Result Report and Activity Report. Representative. 10-14 OPERATION GUIDE or Permitted ID No. registered correctly? Is there an...

Fax System (Q) Operation Guide Rev-1 - Page 6

... Reception 8-12 9 About Network FAX What is Network FAX 9-2 Setup 9-4 10 Troubleshooting Indicators During Sending/Receiving Operation 10-2 Precautions When Turning Power OFF 10-3 Error Messages 10-4 Troubleshooting 10-6 Appendix Character Entry Method Appendix-2 Specifications Appendix-5 Menu List Appendix-6 Received FAX Sizes and Paper Priority (Inch Model Appendix-10 Received...

Fax System (Q) Operation Guide Rev-1 - Page 192

...- Check the setting for paper use. Press [End]. No further operation is canceled. Check the error code shown in the report and refer to perform the job again after printing or deleting the data in... again. off the hook. FAX Box capacity is prohibited by Job Accounting. Try to the Error Code List on , or unplug the power cord and plug it in the FAX Box. 4-30 The...

Fax System (Q) Operation Guide Rev-1 - Page 212

... resend. Send again. U00300 Paper depletion occurred at the recipient machine. Send again. U01092 Communication error occurred during reception. Ask the sender to establish communication with the recipient. Error Code List When a transmission error occurs, one of the following error codes is replaced by an E. Reception was canceled due to an action to failure on the...

Fax System (Q) Operation Guide Rev-1 - Page 213

...party during sub address bulletin board reception. Send again. Communication was interrupted because the password was attempted and the other party. U01720 Communication error occurred during reception of high-speed transmission. U03200 Sub address bulletin board reception was incorrect. OPERATION GUIDE Appendix-17 Error Code Possible Cause/Action U01700 - U01800 -

Fax System (Q) Operation Guide Rev-1 - Page 214

... is not equipped with the other party's machine. Specified sub address box is not registered in any of the originals transfer boxes (sub address boxes). Error Code U03500 U03600 U03700 U04000 U04100 U04200 U04300 U04400 U04401 U04500 U05100 U05200 Possible Cause/Action Sub address bulletin board reception was attempted and the other...