KitchenAid KSB465OB Support Question
KitchenAid KSB465OB Support Question
Find answers below for this question about KitchenAid KSB465OB - PC Blender.Need a KitchenAid KSB465OB manual? We have 1 online manual for this item!
Question posted by wgarff on September 15th, 2012
Part Question For Ksb465 Sho?
Can I change the gasket on the blade portion of the pitcher?
Do you sell the gasket or a kit? The whole assembly? or just the pitcher?
The nut is counter clockwise and it is not obvious how the drive is removed or properly tightened. is there a special tool?
Current Answers
Answer #1: Posted by sdashton on November 4th, 2015 10:44 AM
sdashton
Member since:
November 4th, 2015 Points: 0
Member since:
November 4th, 2015 Points: 0
Although this question is 3+ years old, I am responding since I had a very difficult time finding an answer to a similar question. I needed to remove the blade assembly, which is reverse threaded and must be turned CLOCKWISE to loosen. A spark plug socket fit perfectly over the clutch on the bottom without causing damage to the teeth. A cloth was placed over the blade inside the pitcher and a spanner used over that to hold the blade while turning the socket. (Cloths alone may be sufficient for this repair if the unit is not too tight.) Hope this is helpful to someone else!
Related KitchenAid KSB465OB Manual Pages
Instruction Manual - Page 4
...Blender Assembly 6 Using the Blender ...7 Before Use ...7 Operating the Blender 7 CHOP ICE Feature 7 PULSE MODE Feature 8 Ingredient Cup ...8 Soft Start™ Blending Feature 8 Speed Control Guide ...9
CARE AND CLEANING Cleaning the Blender... to the unique container and blade design, read these instructions before using your new KitchenAid® blender to achieve maximum performance results....
Instruction Manual - Page 5
... , tell you how to potential hazards that can be killed or seriously injured if you what the potential hazard is the safety alert symbol. ENGLISH
Blender Safety
Your safety and the safety of injury, and tell you don't immediately follow the safety alert symbol and either the word "DANGER" or "WARNING...
Instruction Manual - Page 6
...Blades are using electrical appliances, basic safety precautions should always be used by KitchenAid may be used but must be followed to reduce the risk of attachments, including canning jars, not recommended by or near the appliance. When blending hot liquids, remove center piece of table or counter...
13. Handle carefully.
11. Always operate blender with cover in water or other liquid.
...
Instruction Manual - Page 7
ENGLISH
48 oz (1.5 L) Shatter-Resistant Pitcher
Blender Features
Stay-Put Lid with Clear, 2 oz (60 mL) Ingredient Cup
Easy clean, One-Piece Pitcher Design
Patented Stainless Steel Blade
Durable Steel-Reinforced Couplers
Speed Selection Buttons
Clean Touch™ Control Pad
Die-Cast Metal Base
4
Instruction Manual - Page 8
... automatically works to selected speed setting.
ENGLISH
Blender Features
This blender was built and tested to KitchenAid quality standards for fast, thorough, and consistent blending. Pitcher is easy to clean and features tidy cord storage underneath.
5
Our durable blade design is achieved without removing the blade and other parts. This advanced KitchenAid design maintains...
Instruction Manual - Page 9
... death, fire, or electrical shock.
3. See "Care and Cleaning" section. Blender Assembly
1.
Blender is off of the power cord to clean. Rinse parts and wipe dry.
2. Place the 1-piece pitcher on the blender base, and blend to suit your blender for the first time, wipe blender base with a warm sudsy cloth, then wipe clean with a soft cloth...
Instruction Manual - Page 10
... blender base. 2. Before removing the pitcher, press OFF to deactivate the blender, and unplug the power cord. When selected, the blender will operate only when a speed selection button is now ready for chopping ice or other ingredients. 1. The indicator light will stay lit. Do not interfere with blade movement - Before operating the blender, make
sure the pitcher is properly...
Instruction Manual - Page 11
... blender, make
sure the pitcher is released, the blending will stop the blender and then add ingredients. Remove cup and add ingredients at -any-Speed" feature. When button is properly ..., stop , but the blender will remain in place on the blender base. 2. NOTE: PULSE MODE will blink to the selected speed for optimal performance. Put ingredients into the blades, then quickly increases to...
Instruction Manual - Page 12
... any liquid ingredients. Occasional stirring with a warm, sudsy cloth; Remove the pitcher and
empty contents. For storage, the cord can be washed in water. • Do not use abrasive cleansers or
scouring pads.
1. Care and Cleaning
The blender pitcher and blade can be helpful only when blender is recommended. 3. For best results, hand washing is off...
Instruction Manual - Page 13
... also reduce the load on the electrical circuit the blender is connected to the retailer -
Remove the pitcher from the base and free the blades by breaking up or removing the contents at the same time. The blender may be overloaded. The blender stops while blending:
Stir
Mix
Puree
Liquefy
OFF
Pulse Mode
Chop Ice
All indicator...
Instruction Manual - Page 14
... in other rights which vary from state to state or province to arrange for blender when operated outside the country of purchase. Service must be provided by KitchenAid. Damage... Columbia and Canada: Hassle-free replacement of purchase.
See the following pages.
Repairs when blender is used in materials and workmanship. To arrange for service, see the following page for...
Instruction Manual - Page 15
... comparable replacement. KitchenAid will pay for Warranty Service in this quality service. Your repaired Blender will replace your blender with a copy of the proof of purchase (register receipt, credit card slip, etc...of our products meets the exacting standards of the KitchenAid brand that , if your blender should fail within the first year of ownership, simply call our toll-free Customer ...
Instruction Manual - Page 16
...)
How To Order Accessories and Replacement Parts
To order accessories or replacement parts for your blender in Canada, call toll-free 1-800-541-6390. Box 218 St.
All Locations
Before... MI 49085-0218
To order accessories or replacement parts for Service Outside these Locations
Consult your blender in the 50 United States, District of Columbia, and Puerto Rico, call toll-free ...
KitchenAid Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Changing/replacing the water filter - Side by side refrigerator
rotate 90 degrees counter clockwise and then pull Style 2 Filter Animation - Locate the water filter cartridge cap in the base grille. Do not twist the cap when removing the filter; IMPORTANT...onto the new cartridge. Rotate the cartridge cap clockwise to a water source or replacing the water filter, flush the water system. Changing/replacing the water filter - Side by side ... -
KSB354 warranty
...What is one of your model number below. This is the warranty for the KitchenAid KSB354 blender? Download available Owners Manuals/Use & To review your warranty or how the Total Replacement ...Saturday 10AM-5PM, Eastern Standard Time. If you have any further questions, please contact the KitchenAid Customer eXperience toll-free at least 6 characters of the industry's most ... -
Blender Interlock Collar
...;Monday-Friday, 8am-8pm or Eastern Standard Time. Blender Interlock Collar What is the Blender Locking Collar found on several blender models with glass jars, including the KSB354, KSB565 and the KSB655. Saturday 10am-5pm. Dishwasher-safe assembly keeps the blades from rotating until the pitcher is properly attached to the collar and put on the...
Similar Questions
Blender Attachment
The attachment to my immersion blender is bent at the base and will no longer fit snuggly into the b...
The attachment to my immersion blender is bent at the base and will no longer fit snuggly into the b...
(Posted by jeanettegilmore 7 years ago)
Blender Stopped Working
The blender was working hard, but without complaint, mulching orange peels. After a few batches it w...
The blender was working hard, but without complaint, mulching orange peels. After a few batches it w...
(Posted by janetbarr78 8 years ago)
How To Change Rubber Clutch Coupling On A Kitchenaid Blender Model Ksb560mco
(Posted by jbros11djde 10 years ago)
Kitchen Aid Ksb5er Blender Base Change
Ordered part number 9704254 replacement base (red) for our KSB5ER KitchenAid blender. The part sent ...
Ordered part number 9704254 replacement base (red) for our KSB5ER KitchenAid blender. The part sent ...
(Posted by abcdetkooy 11 years ago)
Kitchenaid Blender Mod Ksb560mc0 Not Work Just Flashing The Ligths But Do Not Wo
MY BLENDER JUST FLASHING THE BUTTON BUT NEVER STARTER HELP ME PLEASE...
MY BLENDER JUST FLASHING THE BUTTON BUT NEVER STARTER HELP ME PLEASE...
(Posted by sweetmommy5 12 years ago)