Jenn-Air JGCP436WP Support Question
Jenn-Air JGCP436WP Support Question
Find answers below for this question about Jenn-Air JGCP436WP.Need a Jenn-Air JGCP436WP manual? We have 5 online manuals for this item!
Question posted by Edwicks on July 12th, 2014
How To A Get Replacement Burners On My Grill Under Lifetime Warranty?
Warranty
Current Answers
Related Jenn-Air JGCP436WP Manual Pages
Dimension Guide - Page 1
... designed to LP gas, see the Gas Conversion instructions provided in the package containing literature.
Model/serial rating plate (located on the underside of the cooktop burner base)
Side View of gas available, check with
installation clearances specified on the types of gas that they are accessible without consulting the serving gas...
Installation Instruction - Page 3
... the installer's responsibility to LP gas
■ Noncorrosive leakdetection solution
Parts Supplied Check that are accessible without requiring removal of the cooktop.
■ Provide cutout in left rear corner of the cooktop burner base.
■ It is recommended that a 600 CFM or larger vent hood be installed must conform with the current standards...
Installation Instruction - Page 4
... cm) G 1.4 cm)
Gas and Electric Connection Locations
B
C
A
A.
Gas supply line should be located in from the back of Cooktop A
B
C
G
E
F
A. 27¾" (70.5 cm) B. 1¼" (3.2 cm) C. 7 18.8 cm) D. Grounded ... Model/serial rating plate (located on the underside of the cooktop burner base)
Side View of
the cooktop burner base and 4⁷⁄₈" (12.4 cm) in this...
Installation Instruction - Page 6
... ANSI Z223.1 - In the absence of LP gas must conform with LP gas. ■ This cooktop is recommended that a separate circuit serving only this cooktop. The model/ serial rating plate located on the left underside of the cooktop burner base has information on longer runs may result in the system.
If connected to the...
Installation Instruction - Page 7
... on uneven counters and avoids damage to the countertop surface.
A
B C
A. See "Make Gas Connection" section. 1. Burner Input Rating - Line pressure testing at ½ psi gauge (14" WCP) or lower The cooktop must be isolated from the gas supply piping system by closing . Apply foam strip adhesive-side down
on the left and...
Installation Instruction - Page 8
...compound made for installation requirements. Do not use with arrow pointing up
to cooktop bottom C. Place cooktop into the countertop cutout.
Use a combination wrench and channel lock pliers to...type, size and location.
G. ½" or ¾" gas pipe H. C. Examples of the cooktop burner base and in the "Location Requirements" section for use with the arrow pointing up from the back ...
Installation Instruction - Page 9
...; Dual-Flame Burner
A
A. A
B
A.
The surface burners and grill flames should light within 4 seconds.
The
valve is turned to follow these instructions can result in the "Complete Installation" section. 6.
Test all connections by brushing on top of the Use and Care Guide or contact the dealer from parts package. Remove cooktop burner caps, burner bases and grates...
Installation Instruction - Page 10
... light with one arm and reconnect the griddle switch connectors and/or grill indicator light connector.
B A
A. Remove console and set aside.
8. Lower flame
Single Flame Burner
10.
Replace the round gasket.
16.
Single flame burner adjustment screw (on each side of the cooktop burner base.
5. Remove the round gasket from the control console. NOTE: When you...
Installation Instruction - Page 11
..., authorized gas company personnel, and authorized service personnel. Push the cooktop back into the cap. Replace burner grates. 24. Turn the manual shutoff valve to locate the "NAT" or "LP" position. Install a shut-off valve. Examples of range cooktop
A
A.
Look at each side of the cooktop.
19.
Gas pressure regulator
C
D. LP position E. Plug in death...
Installation Instruction - Page 12
...WCP)
The cooktop and its individual manual shutoff valve during any pressure testing of medium burner base. Remove the burner base. Replace the burner base. 8. Replace burner cap. ...water column above the manifold pressure shown on the model/serial rating plate. Burner base
C. Replace with package containing literature.
7.
Refer to "Complete Installation" in the "Installation...
Installation Instruction - Page 13
... its individual shutoff valve must be at ½ psi gauge (14" WCP) or lower
The cooktop must be disconnected from the cap by using a wrench, turning the access cap counterclockwise.
2. Burner base
4. Replace with medium
burner, LP gas only)
A
Small Burner
B
A. LP position
3. The inlet pressure to or less than ½ psi (3.5 kPa). Line pressure...
Installation Instruction - Page 14
...) long.
LP gas flames have a very distinct blue flame ¼" (0.64 cm) to adjust the "LO" setting for proper burner ignition, operation, and burner flame adjustments. STRIP CIRCUIT
Griddle 120V Control Wiring Diagram To Cooktop Stand-Alone
R
P2-1
P1-1 OR/W 1320W/120V OR/W
Lamp 120V
BU
W
Rotary Control
P1-3 W P1-4 V
W
RTD
W
WV V
W
P2...
Installation Instruction - Page 15
...
RTD - Verify proper operation after servicing.
6 Burner Cooktop Reignition Wiring Diagram
W
BU
Reignition BU Module
Electrodes Output Control Input
G
RR R BR RY RG
2
1
SW1
SW2
R
SW3
SW4
OR
R
R Griddle Spare W
BK
4
3
L
Y
N
G
BK
Grill Spare
GND
W
6
5
R
Power
W
Cord
L
N
BK W R
GND
Power Cord Only To Cooktop Stand-Alone
Version
Main -
WIRING DIAGRAMS
Caution...
Installation Instruction - Page 16
... Input
G
R
R
R
BU
R
BR
R
Y
SW1
SW2
R
SW3
SW4
BU
2
1
R Griddle Spare W
BK
BK Grill Spare W
Power
Cord
L
N
R W
BK W
R
GND R
GND
Main - Gas Burner Temperature
Sensor
Heating Element
Indicator Lamp
16 Harness Power Spare
L
OR
N
Y
4
3
Cooktop Front View
Power Cord Only To Cooktop Stand Alone
Version
LEGEND
Ground Plug With Receptacle (Chassis) Female With Male...
Use and Care - Page 9
...off and the oven and cooktop are cool. If the burner needs to be adjusted, contact a trained repair specialist. Turn on some models)
B A
4.
Clean clogged burner ports with hot, soapy water... on the griddle and cook to desired temperature. 3. Incorrect B. Replace the burner cap, making sure the alignment pins are properly aligned with a damp cloth.
3. Clean the gas ...
Use and Care - Page 10
... and precooked sausages
325°F (163°C)
Ground meat patties
350°F (177°C)
Grilled sandwiches
325°F (163°C)
Fish steaks, fillets 325°F (163°C)
Eggs
300...will take on 2 surface burners at the same time.
■ For more information, contact your local agricultural department.
Aluminum and copper may scratch the cooktop or grates.
Preheat Chart...
Use and Care - Page 11
...affect the finish. SURFACE BURNERS
GRIDDLE MODULE
Clean the griddle shortly after cleaning either the surface burner controls or the grill module control, make sure...replacing knobs, make sure knobs are suggested first unless otherwise noted. Sealed Burner models See "Sealed Surface Burners" section.
11 NOTE: When replacing knobs after removing food and the griddle has cooled down.
COOKTOP...
Use and Care - Page 12
...burner and contact a service technician. Contact a trained repair specialist. Let it dry. Level the cooktop. Thoroughly defrost foods.
12
See "Cooktop Controls" section.
■ Is the cooktop level? Griddle results not what expected
■ Is the proper cookware being used ? Replace...to a setting.
■ Are the burner ports clogged? Cooktop cooking results not what expected
■ ...
Use and Care - Page 14
...; Magnetron tube
■ Glass ceramic cooktop: if due to thermal breakage
■ Sealed gas burners
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Costs associated with the product, Jenn-Air will pay for factory specified parts for repairs. The cost of repair or replacement under this limited warranty. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS...
Warranty - Page 1
... controls
■ Touch Pad and microprocessor
■ Magnetron tube
■ Glass ceramic cooktop: if due to repair or replace appliance light bulbs, air filters or water filters. Service calls to thermal breakage
■ Sealed gas burners
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Damage resulting from accident, alteration, misuse, abuse, fire, flood...
Similar Questions
Replacing Jenn-air Jgd8130ad Top Valves?
I have a Jenn-air JGD8130AD.The two right valves have gotten tight, and one doesn't shut off the gas...
I have a Jenn-air JGD8130AD.The two right valves have gotten tight, and one doesn't shut off the gas...
(Posted by colonalfredo 9 years ago)
How To Adjust The Burner Flames
Burners are way to high on low and food will not simmer.
Burners are way to high on low and food will not simmer.
(Posted by cderstine 9 years ago)
How To Replace Burner Gas Valve On Jenn-air Cvgx2423
I ordered a new valve and assume that the replacement burner gas valve screws into the manifold, can...
I ordered a new valve and assume that the replacement burner gas valve screws into the manifold, can...
(Posted by jblapilusa 10 years ago)
Burners Get Warm But Not Hot
I have a jennair model JED8130ADB, all four burners will get warm but none hot enough to boil water....
I have a jennair model JED8130ADB, all four burners will get warm but none hot enough to boil water....
(Posted by jblawrence1 10 years ago)