JVC DLA-X550R Support Question
JVC DLA-X550R Support Question
Find answers below for this question about JVC DLA-X550R.Need a JVC DLA-X550R manual? We have 1 online manual for this item!
Question posted by sam381966 on April 17th, 2022
Jvc Dla-x550r “device Is Too Hot” Message
Hi,I keep getting a warning message in my jvc dla-x550r saying Warning device is too hot, shut down or run cooler. I select run cooler but the message reappears a few minutes later. There are no lights or performance changes. I cleaned the screen, and it's a fairly new bulb. The unit was recently moved, but otherwise no changes have occurred. Can you tell me what the issue might be, and how I can resolve it?Thank you,Sam
Current Answers
Answer #1: Posted by Odin on April 17th, 2022 5:01 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
After moving, has the unit been exposed to direct sunlight, or otherwise to higher temps? If not, the unit is malfunctioning and should be serviced (or returned if possible). For referral or warranty information, use the contact information at https://www.contacthelp.com/jvc.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Answer #2: Posted by SonuKumar on April 17th, 2022 10:03 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,621,300
Member since:
May 9th, 2021 Points: 16,621,300
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related JVC DLA-X550R Manual Pages
Instruction Manual - Page 1
... nº de serie que aparece en la parte inferior lateral de la caja. For Customer use :
Enter below the serial No. Model No. N° de modèle DLA-X950R / DLA-X750R / DLA-X550R
N° de série
Not suitable for future reference. D-ILA PROJECTOR
DLA-X950R DLA-X750R DLA-X550R
INSTRUCTIONS
Set up
Operate
Adjust/Set
Maintenance Troubleshooting
.
Getting Started
.
Instruction Manual - Page 2
... APPARATUS MUST BE EARTHED.
This projector is equal or less than 30dB(A) according to qualified service personnel. Increase the separation between the equipment and receiver.
FCC INFORMATION (U.S.A.
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Manage in Taiwan only
.
Getting Started
Safety Precautions
IMPORTANT INFORMATION...
Instruction Manual - Page 3
...placing the product on a cart,
PORTABLE CART WARNING (symbol provided by RETAC)
care should use... are required, be
easily unplugged.
- Getting Started
IMPORTANT SAFEGUARDS
Electrical energy can cause
damage... lightning storm, or when it is in performance, this product from a low temperature to ...product on the label. Place the projector near water. Slots and openings in ...
Instruction Manual - Page 4
...light-source lamp used for installation. otherwise, the attaching fixture of the projector...it run ...light is unclear, please consult your dealer, or the nearest authorized JVC...perform an internal test. If installation is turned on the device.
* DO NOT allow any kind of moving images, e.g. If the unit is no problem with still images of about 5-15 minutes every 30-60 minutes...
Instruction Manual - Page 5
...JVC KENWOOD U.K. Power cord
The power supply voltage rating of this equipment. Ensure that the power cable used for the projector ... with the following power cord. CONSULT A COMPETENT ELECTRICIAN. Getting Started
POWER CONNECTION
For USA and Canada only Use only... or colored black.
For United Kingdom
For European continent countries
WARNING: Do not cut off the main plug from this product ...
Instruction Manual - Page 8
... 21 Adjusting the Projector Screen 23 Adjusting ...
Adjust/Set Selecting an Image ...messages appear 65
Others External Control 66 RS-232C Specifications 66 TCP/IP Connection 66 Command Format 67 Remote Control Code 68 Communications Example 69 Specifications 70 Index 77
Symbols used in the Menu 41 List of the above symbols are supported by DLA-X550R. Getting Started
Contents
Getting...
Instruction Manual - Page 10
Getting Started
Controls and Features
Main Unit - Front
D
E
E
C
AB
. Do not look through the lens while an image is a projection lens.
B Lens cover 4 5
The lens cover opens/closes when the power supply is turned on the rear/bottom)
The inlets take in use of hot... and left sides at the rear of the projector can be adjusted by turning the foot. (0 to 5 mm) (P. 17...
Instruction Manual - Page 11
... I] keys: Selects an item
[MENU]: Displays the menu
.
[BACK]: Returns to the "Operation panel" in the diagram below. Getting Started
Main Unit - Rear
F
F
J
I Input terminals
In addition to this terminal. J Lamp cover
When replacing the light source lamp, remove this area when using it. * There is also a remote sensor at the front. M Power...
Instruction Manual - Page 12
... screw hole is fitted to devices that improper connection may damage the projector. (Tip=DC +12 V, Sleeve=GND)
12 A [HDMI 1] input terminal
B [HDMI 2] input terminal
For connecting to the M3 lock hole. The depth of Rear Face
A
BC
D F
E
.
Note that support HDMI output. (P. 18) It is 3 mm.
Getting Started
Main Unit -
It is...
Instruction Manual - Page 14
... unit varies with an exposure to direct sun light or high temperature. Effective Range of distance A...0 Insert the batteries according to direct sun light or high temperature. Control through reflection off ...
Remote Control
. Storing the remote control for five minutes.
This unit
30° 30°
20°...has to be brought closer to the projector to operate, it means that the total...
Instruction Manual - Page 15
...15°
0 Malfunction may cause dirt to attach to the light path, thereby resulting in use. Using the unit at a location...unit discharges a large amount of the exhaust vent, hot air will heat up when in dark images or dull...;
5°
.
Installing the Projector
Set up
Precautions during Installation
Please read the following This unit is a precision device. Do not install at an ...
Instruction Manual - Page 16
... shut down . * Leave a clearance of at an accessible height to the surrounding temperature.
Or install the circuit breaker at the bottom, and fasten using the unit with screws 4 Locations
Air Inlets
. Remove the four feet at an accessible height to 2.0N m. Set up
Precautions during Mounting
Securing (mounting) the projector
Securing the projector...
Instruction Manual - Page 21
... up (green) During lamp startup
STANDBY/ON LAMP
WARNING
STANDBY/ON LAMP
WARNING
.
13 2
2 Choose the image to project
Remote control: press the [HDMI 1] or [HDMI 2] button Projector unit: press the [INPUT] button to switch the input 0 Play back the selected device to project the image. "STANDBY/ON" lights up (red) In standby state
"STANDBY/ON...
Instruction Manual - Page 22
...button Projector unit...light to cool down the lamp (Cool-down mode
"STANDBY/ON" lights up (red) In standby state
STANDBY/ON LAMP
WARNING
STANDBY/ON LAMP
WARNING...light. 0 After the light goes off within approximately 60 seconds after it has been turned on. 0 The power cannot be turned off , the fan will run for details. Operate
22 "STANDBY/ON" blinking (red) In the Cool-down mode). message...
Instruction Manual - Page 32
... refer to get ready a commercially available optical sensor and the projector calibration software program. Cinema 2
-
Off
Disables color space adjustment. THX
THX*3
3D THX*3
Color space of the HDTV standard. *2
Reference
- Color space that is set "Color Profile" to Custom 6
Saves the auto calibration values.
0 To perform auto calibration, you can select one of...
Instruction Manual - Page 57
... lamp unit. This could cause significant deterioration in the performance of the lamp is still high, and may cause ...not touch the surface of the unit. Allow a cooling period of a projector suspended from the power outlet
2 Remove the lamp cover
0 Remove the screw...Loosen the screws of the lamp unit
0 Loosen the screws with a message displayed on the screen and by
the indicator. (P. 74)
Lamp ...
Instruction Manual - Page 61
... that, insert the plug again. Perform the following points.
P. 22
Power shuts down mode, turn on some screens. This unit is designed to "High" during 3D mode, the fan will make louder noise than usual since it is a digital device. Action
Refer to worry about the following symptoms are not malfunctions.
You do...
Instruction Manual - Page 63
...projector unit, or immediately after the projector is dark
Check Is the lamp near or too far away Set the unit at a correct distance from that in the "Information" menu.
a fluorescent light... Signal" correctly. Is the image correctly adjusted?
P. 46
Is the AV device properly connected? Connect the AV device properly.
This is P. 46 different from the screen. Adjust the focus. ...
Instruction Manual - Page 65
... input (The names of the
projector unit or the remote control.
Lamp replacement Back BACK
.
Message
No Input
. Description
Action
0 No device is connected to be used with...possible. A video signal that cannot be
Get ready a new lamp unit and replace
replaced soon. Indicates that can be displayed in yellow). When the following messages appear...
as soon as "HDMI-1" ...
Instruction Manual - Page 70
...V, 0.1 A
3D synchro
Dedicated terminal for Direct drive Image Light Amplifier.
*3 D-ILA devices are connected is the abbreviation for High-bandwidth Digital Content Protection ... that some cases due to P. 71. Specifications
Product Name
D-ILA Projector
Model Name
DLA-X950RB, DLA-X750RB, DLA-X550RB*1
Display Panel/Size
D-ILA device *2, 3 0.7" (1920 x 1080 pixels) x 3 (total no...
JVC Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
FAQ - DVD Recorders & Players
... compliant disc i.e. This disc cannot be copied and can only be in Europe). In order to perform an auto tuner setup the unit needs to connect your DVD via the COMPONENT OUT. DVD Recorders & Players I cannot get a picture from the recorder a composite, component, S-video, or HDMI cable must "Finalize" the DVD before... -
FAQ - DVD Recorders & Players
...screen but will be no indication available to tell if recording of specific program is restricted in the MENU to perform...Hong Kong) Region 4: Australia, New Zealand, Pacific Islands, Central ...get the "Copy Protect" message on the unit it is a pass-through RF connection. You will resolve this they need to connect your DVD via component output? Press OUTPUTSTATUS button and select... -
FAQ - Televisions/HD-ILA Projection
... get sound, either change ... My DVD movie says WIDESCREEN on top ... or blue light flash on the screen if remote ...new digital TV broadcast and there is working batteries in some cases using the audio cables select...000. Controlling audio devices while using an...screen and then movie will be still showing black bars and can hear the fan running inside an HDILA Television to fill entire TV screen...
Similar Questions
Dear All How I Change The Screen Size (16:9,2.35:1) My Screen Size Is 2.35:1
(Posted by Dvirm25 2 years ago)
Why Won't My Projector Turn On, Remians In Standby?
When i try to turn on the projector it defaults to standby, not powering up. There is no indication ...
When i try to turn on the projector it defaults to standby, not powering up. There is no indication ...
(Posted by pzingrone 4 years ago)
Does Anyone Know The Factory Reset For A Jvc Dla Hd-250 Projector?
Projector turns on, lens cover retracts, but projector makes rapid tick, tick, tick sound as if it t...
Projector turns on, lens cover retracts, but projector makes rapid tick, tick, tick sound as if it t...
(Posted by AET 9 years ago)
How To Reset Lamp Hours On
Dla-sx21 Projector
How to reset the lamp hours on DLA-SX21 projector
How to reset the lamp hours on DLA-SX21 projector
(Posted by tesfayis 10 years ago)
Second-hand Jvc D-ila Projector With Dla-sx21 Lamp (f=29,00 Mm - 37,7 Mm)
Dear sir, madam, I wish to buy the above mentioned projector (estimated age: 10 years?) Could you ...
Dear sir, madam, I wish to buy the above mentioned projector (estimated age: 10 years?) Could you ...
(Posted by joostvanbogaert 12 years ago)