Husqvarna GT48XLSi Support Question
Husqvarna GT48XLSi Support Question
Find answers below for this question about Husqvarna GT48XLSi.Need a Husqvarna GT48XLSi manual? We have 2 online manuals for this item!
Question posted by aylorr on April 18th, 2015
Smartswitch Will Not Turn Green And Start
Smartswitch will not turn green and start. Followed all troubleshooting in manual with no success.Seat was left folded up in heavy rain, could seat operator presence switch be shorting and causing this?
Requests for more information
Request from perry268 on September 24th, 2017 2:05 PM
Smart switch stay on parking indicator light stays red, cutting blades indicator light on red and the on/off indicator light in multi color red
Smart switch stay on parking indicator light stays red, cutting blades indicator light on red and the on/off indicator light in multi color red
Current Answers
Answer #1: Posted by aylorr on April 21st, 2015 3:13 PM
aylorr
Member since:
April 18th, 2015 Points: 0
Member since:
April 18th, 2015 Points: 0
I found a solution myself.
After testing all the safety switches and connections (brake, blade, etc) things still did not work.
I decided to try to do a reset on the switch combination as described in the on line owner's manual, but holding 1 and 3 buttons down for three seconds until blue light came on and stayed on.
I then entered a new code, pushed the blue switch, and after some whirring noises, the green light began to flash, then held steady, and the engine started.
Related Husqvarna GT48XLSi Manual Pages
Owners Manual - Page 2
... of control and tipover accidents, which could cause the machine to a complete stop before starting , stopping, or turning on the machine and in the manual before cleaning the machine, removing the grass catcher, or unclogging the discharge chute.
• Operate machine only in .
2 GENERAL OPERATION
• Read, understand, and follow all instructions on a slope. Stop machine if...
Owners Manual - Page 3
...contact with safe machine operation. Tragic accidents can occur if the operator is an open device.
3
Ensure the area is spilled on the slope. Avoid starting, stopping, or turning on towed equipment....of age before operating a pedestrian controlled lawn mower and a minimum of 16 years of the fuel tank or container opening at the hitch
point.
• Follow the manufacturer's ...
Owners Manual - Page 5
... after month and year indicated on label (label is mentioned in the Operation section of one hour at the factory with the instructions that follow .
WARNING: Before starting, read, understand and follow all instructions in this manual. Continue with the exception of those parts left hand is located between terminals) charge battery for charging instructions). •...
Owners Manual - Page 6
... the factory for replacing motion and mower blade drive belts in safe operating condition. ✓ Ensure Operator Presence System and Reverse Op- CHECK BRAKE SYSTEM
After you start the engine.
✓ Ensure brake system is in the Service and Adjustments section of this manual).
✓ It is important to purge the transmission before you learn...
Owners Manual - Page 7
... death, serious injury and/or property damage. Learn and understand their meaning.
REVERSE
NEUTRAL
HIGH
LOW
COLD WEATHER FAST STARTING POSITION
SLOW
SMARTSWITCH™ IGNITION
ENGINE OFF REVERSE OPERATION
SYSTEM (ROS)
ENGINE ON
ENGINE START
PARKING BRAKE
MOWER HEIGHT
LIGHTS ON
FUEL BATTERY
REVERSE FORWARD CRUISE CONTROL
MOWER LIFT CLUTCH/BRAKE PEDAL
15
15...
Owners Manual - Page 8
....
(M) FREEWHEEL CONTROL - Used for starting the engine.
(C) PARKING BRAKE - Indicates a starting fault when the parking brake is engaged.
(F) SMARTSWITCH IGNITION (SSI) BUTTON - Used to indicate low battery voltage or a charging system fault.
(J) CRUISE CONTROL LEVER - OPERATION
KNOW YOUR TRACTOR
READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with...
Owners Manual - Page 9
... engine is running , hot engine exhaust gases may cause engine to stop engine when stopping tractor on grass areas. B
C
• Press SSI button (F) once to "backfire".
• While seated in the seat will shut off .
Fig. 6 SMARTSWITCH SAFETY SYSTEM
Your tractor is equipped with an operator presence sensing switch. ENGINE -
• Move throttle control (D) to restart the...
Owners Manual - Page 10
... operate engine at full speed (fast). • Operating engine at slow speeds may cause... minimize the risk of grass being mowed.
• The average lawn should be used for long periods of grass in desired cutting height...• Put attachment lift lever in turns with differential lock engaged. • To disengage differential lock, push differential lock
switch to the "OFF" position.
D Y...
Owners Manual - Page 11
..."
3/4"
Fig. 11
TO OPERATE MOWER
Your tractor is equipped with an operator presence sensing switch. OPERATION
TO ADJUST GAUGE WHEELS (See...Start mower blades by the operator to desired cutting height. (See "TO AD- You must remain fully and centrally positioned in desired height of this manual.) • With mower in the seat to prevent the engine from hesitating or cutting off when operating...
Owners Manual - Page 12
... tractor.
HEADLIGHTS
Headlights can be used to turn headlights on a truck or a trailer, ensure hood is disengaged by and comply with attachment lift control.
• Raise seat and pull freewheel control up and indicate the battery status as follows:
RED
Charge necessary
RED AND GREEN Charge recommended
GREEN
Charge not necessary
• Press the battery...
Owners Manual - Page 13
... this manual.) • To change oil for additional information. NOTE: When the indicator flashes green, the passcode has been accepted. Do not overfill. • For cold weather operation you should...or using fuel stabilizer. Add stabilizer to primary position. Always follow the mix ratio found on the seat). Raise seat to separation and formation of an engine while in minimizing ...
Owners Manual - Page 14
...SMARTSWITCH IGNITION UNLOCK" as previously described.
3. Move throttle control beyond fast position ( ) into the engine.
OPERATION
TO START ENGINE
NOTE: The default passcode "321" is preset at the factory and should be warmed up as follows... start attempt.
• The blade switch symbol (EE) will flash green.
3. AUTOMATIC TRANSMISSION WARM UP • Before driving the unit in operating ...
Owners Manual - Page 15
... operating attachments, select a ground speed that clippings will discharge away from dried clippings.
See "TO LEVEL MOWER HOUSING" in this manual. Make first cut area to ensure better mowing performance and proper discharge of manual.)
3.
Fig. 20
• If grass is extremely tall, it should be used .
15 Sitting in the tractor seat, start engine...
Owners Manual - Page 17
...with heavy cloth.
• Remove blade bolt by turning ...operator
to leave the seat without first setting the parking brake should not start unless the parking brake is engaged, and the attachment clutch control is running , the SmartSwitch Ignition
(SSI) button (F) solid green...cause tire damage.
Adding or checking level of your tractor is not necessary.
CHECK OPERATOR PRESENCE...
Owners Manual - Page 18
...approximate capacity see "PRODUCT SPECIFICATIONS" section of this manual.
• Use gauge on oil fill cap/... lock the drain valve by pushing inward and turning counterclockwise.
• To open, pull out ...23 - 25)
Determine temperature range expected before starting in a suitable container. SAE VISCOSITY GRADES
5W-...is not required for the life of operation or at "FULL" line on oil...
Owners Manual - Page 20
... area to lock the adapter on the tractor,
re-start the engine and place the throttle lever in the "DISENGAGED" position. Turn the water off . WARNING: A broken or missing ...Operator's Manual) onto the end of your garden hose.
4. Pull back the lock collar of the nozzle adapter and push the adapter onto the deck washout port at the left end of its deck wash system. Turn the water on your lawn...
Owners Manual - Page 23
...heavy cloth.
• Raise mower to think the mower is cutting lower.
CAUTION: Blades are equal. Measure distance (B) to adjust.
• With a 3/4" or adjustable wrench, turn of the blade. A
TURN NUT RIGHT TO RAISE MOWER
TURN NUT LEFT... is in its highest position. • At both sides are sharp. Protect your lawn and lead you can raise the low side of mower or lower the high side....
Owners Manual - Page 26
...as shown. INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your battery is too weak to positive (+) battery
terminal ...
charged battery. • RED cable last from starting , follow this manual). Replace primary operation fuse with a 20 amp and the differential lock...
REPLACING BATTERY (See Fig. 47)
WARNING: Do not short battery terminals by allowing a wrench or any other end of...
Owners Manual - Page 27
... when there is a fault with courtesy lights that the battery voltage is below normal operating level. G
I ) will not be lit if the parking brake has not been engaged during a start attempt.
• The blade switch symbol (EE) will blink green when tractor is ready to indicate system functions or faults.
The SSI button will...
Owners Manual - Page 29
...4. Corroded battery terminals. 6. Faulty operator presence switch(es).
1. Replace fuse. 5. ...switch. 8. Engine clicks but will not turn over
1. Faulty solenoid or starter.
1. Check/replace solenoid or starter. Move throttle control to start . 3. Connect and tighten spark plug wire.
11. Clean/replace muffler.
13. Tighten blade bolt. 2. TROUBLESHOOTING
PROBLEM Will not start...
Similar Questions
Why Am I Having Such A Very Hard Time Trying To Start My 440 Chainsaw.
Is there a secret? i've taken it to two different places. and they started it on the first or second...
Is there a secret? i've taken it to two different places. and they started it on the first or second...
(Posted by pandorabird 2 years ago)
Surging Problem With Husqvarna Yth20k42,kohler 7000
I am trying to access the govenor, which apparently is near the carburetor.The fly-wheel cover has f...
I am trying to access the govenor, which apparently is near the carburetor.The fly-wheel cover has f...
(Posted by castbankes 2 years ago)
Smart Switch
mower starts and runs great for about 5 minutes then just shuts off, all the lights on the switch go...
mower starts and runs great for about 5 minutes then just shuts off, all the lights on the switch go...
(Posted by sturgonon 3 years ago)
My Husqvarna Srd17530 Just Clicks When I Turn The Key
Fuse looks o.k.?
Fuse looks o.k.?
(Posted by pamelalcorbin 10 years ago)