Hunter 28679 Support Question
Hunter 28679 Support Question
Find answers below for this question about Hunter 28679.Need a Hunter 28679 manual? We have 4 online manuals for this item!
Question posted by stevecarrico55 on November 30th, 2013
Light Switch For 28679
Where to you order light switch assembly
Current Answers
Related Hunter 28679 Manual Pages
Installation Guide - Page 1
...is suitable, go to your fan manual and begin with the joist or support brace.
4-3. Make sure the circuit breakers to the fan supply line leads and associated wall switch location are turned off position,...wires extend from any hardware store or electrical supply house.
5-4.
o Six inches of the fan and light kit. Cut a 4" diameter hole through the outlet box so that both the inner and...
Owner's Manual - Page 1
Date Purchased
Where Purchased
Type 2 Models
Owner's Guide and Installation Manual
English
Español
Form# 42439-01 20100615 ©2010 Hunter Fan Co. For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Model Name
Model No.
Owner's Manual - Page 2
... Ready 6 2 • Installing the Ceiling Plate 7 3 • Assembling and Hanging the Fan . . . 8 4 • Wiring the Fan 9 5 • Installing the Canopy and Canopy
Trim Ring 10 6 • Assembling the Blades 11 7 • Completing Your Installation With
a Bowl Light Fixture 12 8 • Operating and Cleaning Your
Ceiling Fan 14 9 • Troubleshooting 15
Cautions and Warnings...
Owner's Manual - Page 3
... brace that will hold the outlet box and the full weight of the fan and light kit. If your new Hunter fan. Choose the Fan Site
Proper ceiling fan location and attachment to the building structure are at least 8 feet high.
• e fan blades have no obstructions to the joist or support brace by an...
Owner's Manual - Page 4
...support brace and outlet box. Step 4 - Attach the fan supply line to the fan supply line leads and associated wall switch location are unfamiliar with the joist or support brace.
...Outlet Box
4-1. Cut the Ceiling Hole
2-1. Cut a 4" diameter hole through the inner holes of the fan and light kit. Position it will support the full weight of the outlet box.
4-4. Obtain a UL-approved ...
Owner's Manual - Page 5
... use only the hardware supplied.
5 42439-01 • 06/15/10 • Hunter Fan Company Installer's Choice and Optional Accessories
Support Brace
Standard Mounting Style
Ceiling Outlet Box
Standard Mounting... than 8 feet high
CAUTION: To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to assure stability and wobble-free ...
Owner's Manual - Page 6
... the ceiling joist or other suitable support in ceiling. • Drill holes for installing the fan: • Electric drill with 9/64" bit • Standard screwdriver (magnetic tip recommended) ... • Wrench or pliers • Ladder (height dependent upon installation site)
Checking Your Fan Parts
Carefully unpack your Hunter dealer or call Hunter Technical Support Department at 888-830-1326 ...
Owner's Manual - Page 7
...fasten a prominent warning device, such as a tag, to the outlet box and associated wall switch location. Drill two pilot holes into the wood support structure through the outermost holes in the... ceiling plate into the 9/64" pilot holes;
If you
drilled in diameter. Your fan comes with the pilot holes you cannot lock the circuit breakers in place and were not removed ...
Owner's Manual - Page 8
... profile mounting, the downrod is fully installed, 2-3 threads on the threads.
Note: When the pipe and ball assembly is replaced with three low profile screws. 3 • Assembling and Hanging the Fan
WARNING: Fan may fall if not assembled as directed in the ball. 3-3. Standard or Angled Mounting Steps 3-2 - 3-3
Downrod
Setscrew
Canopy
Canopy Trim Ring
Low...
Owner's Manual - Page 9
...) from the ceiling plate and the green ground wire from the fan. 4-5. Connect the remaining wires as follows: Dual Switch Wiring:
• The black wire (ungrounded) from the ceiling to the ...the outlet box.
9 42439-01 • 06/15/10 • Hunter Fan Company
Wire Connector Dual Switch Wiring
Single Switch Wiring Turn the splices upward and push them , then twist clockwise until tight....
Owner's Manual - Page 10
...remain engaged while swinging the canopy for the following steps could cause the fan to fall. Swing the fan up to align the canopy screw holes with the screw holes aligned, ...Step 5-3 Canopy Canopy Trim Ring
Canopy Screw
10 42439-01 • 06/15/10 • Hunter Fan Company Note: Your fan may have multiple tabs and grooves that the tabs in the hanger ball.
The canopy trim ring will...
Owner's Manual - Page 11
... attract dust and dirt. Refer to clean the blades. Note: The blades on this fan have been treated with a protective cloth to prevent
scratching the blades. 2. Carefully remove the ...furniture polish or any residue, as they are installed. 6 • Assembling the Blades
Our exclusive Easy Lock™ blade assembly enables you will damage the protective Dust Armor on the blades. Repeat...
Owner's Manual - Page 12
... to the fan, partially
install two housing assembly screws into the upper switch housing. 7-2. 7 • Completing Your Installation With a Bowl Light Fixture
Upper Switch Housing
Plug Connector
Housing Assembly Screw
WARNING: Use only the light fixture supplied with this ceiling fan contains a device that restricts its light output. To attach the lower switch housing assembly to be...
Owner's Manual - Page 13
... Disc
Metal Rod
Glass Bowl
Breakaway Connector
Cover Plate Finial
13 42439-01 • 06/15/10 • Hunter Fan Company Install candelabra bulbs (60 Watt Maximum) into the sockets. 7-7. Then, thread the light pull chain through the grommet hole in the cover plate and glass bowl. 7-10. 7 • Completing Your Installation...
Owner's Manual - Page 14
...furniture polish or any other cleaners that separates if the chain is jerked.
Restart fan. Reversing
Switch
In warm weather, use downward air flow pattern
In cold weather, use
an ... with Hunter's Dust Armor protection, making the blades less likely to the light fixture. In winter, having the fan draw air upward (clockwise blade rotation) will damage the
8-6. Remove surface ...
Owner's Manual - Page 15
...) or visit us at our Web site at the wall switch. Tighten the blade assembly screws and blade iron armature screws until snug. 2.
Problem: CFL bulbs flicker when controlled by a dimming remote or wall control 1. fan does not move. 1. Tighten all the blades. CFL light bulbs are installed meet the specifications on , replace fuse...
Parts Guide - Page 1
.../Shade Light bulb / Bulb Balancing Kit
Model #
28679
Asm. Hardware (Drawn to Scale)
x 1 x 2 x 4 x 2 x 3 x 4 x 1
x 4
Low Profile Washer 3" Wood Screw
Flat Washer 1.5" Wood Screw Screw, Low Profile
Canopy Screw
Setscrew
Mouting Isolator
Balancing
x 1
Kit
Wire
x 4
Connector
Screw, Switch
x 3
Housing Assembly
Hanger Bracket Assembly
Blade Assembly
Switch Housing Assembly
Fan Parts...
Similar Questions
Need A New Capacitor And Switch Assembly .maybe A New Motor
2 new capacitors,2 new switches,2 new motor
2 new capacitors,2 new switches,2 new motor
(Posted by Stevecourtier 3 years ago)
The Fan Was Working Fine I Turned Off Went Back Later Try To Turn On Nothing Wor
no light no fan.
no light no fan.
(Posted by dquintana1953 5 years ago)
Need Hunter Part No. 98378.01, Light Kit Assembly, For Ceiling Fan Model 28679
Hunter says they do not make this model any longer and that they do not have part. Can you help me f...
Hunter says they do not make this model any longer and that they do not have part. Can you help me f...
(Posted by larrypricesimmons 10 years ago)
Light Switch
The light switch pull chain switch for my Hunter 23908 ceiling fan does not work. it does not appear...
The light switch pull chain switch for my Hunter 23908 ceiling fan does not work. it does not appear...
(Posted by jos0387 11 years ago)