Hunter 23710 Support Question
Hunter 23710 Support Question
Find answers below for this question about Hunter 23710.Need a Hunter 23710 manual? We have 4 online manuals for this item!
Question posted by Stevecourtier on January 22nd, 2021
Need A New Capacitor And Switch Assembly .maybe A New Motor
2 new capacitors,2 new switches,2 new motor
Current Answers
Related Hunter 23710 Manual Pages
Installation Guide - Page 1
... e fan blades have now successfully prepared your new Hunter fan.
CAUTION: All wiring must be in the box align with 2 • Installing the Ceiling Plate. Tools and Supplies You May Need
• ...local standards and ANSI/ NFPA 70. Fan Support System o Fan attaches directly to the fan supply line leads and associated wall switch location are unfamiliar with national and local...
Owner's Manual - Page 1
...C. Be certain electricity is securely mounted to avoid any hardware store or electrical supply house. fan with national and local electrical codes. A. TO FLOOR
24" CLEARANCE
TO OBSTRUCTIONS
Figure 1.... the box so the outermost holes will need a 4" x 1-1/2" or 4" x 1/2" outlet box and wire nuts (2) which can weigh up to the motor and the fan
blades. WARNING!
1. To avoid possible ...
Owner's Manual - Page 2
... the ceiling plate mounting screws only enough to use. Step 4: Installation of elongated slots in the fan falling. Use (2) #10 wood screws 3" long and (2) flat washers for mounting screws 9/64" diameter. NOTE: Assembly Methods for Installer's Choice Hanging System
Your new Hunter fan can be in place. Installing Ceiling Plate
NOTE: When mounting the...
Owner's Manual - Page 3
...extend out the top of the fan as a general-use switch. CAUTION: No bare wire or wire strands should be tightened very securely.
Step 7: Finish Fan Assembly A. sion flanges located on a ... (tighten securely)
CANOPY TRIM
PIPE NIPPLE ADAPTOR
Figure 5C
B.
CAUTION: Do not lift motor by wires.
Connect black electrical supply lead to control a lighting accessory, connect the black...
Owner's Manual - Page 4
...fan. See Figure 8A.
Assemble lower switch housing to the blade bracket. ASSEMBLY SCREWS
UPPER SWITCH HOUSING
UPPER PLUG CONNECTOR
LOWER PLUG CONNECTOR
POWER / ON-OFF SWITCH
LOWER SWITCH HOUSING
BLADE
BREAKAWAY CONNECTOR
REVERSING SWITCH... fan. See Figure 10. Make sure all blades. Rotate the fan until it is free to rotate in the trim with the ball grooves you will need ...
Owner's Manual - Page 5
... your Hunter dealer. When first operating fan,
determine direction of Fan
A. Push switch firmly to operate. Blade cracked. 4. Use balancing kit. (See Step 8C.) 3.
If this sequence: "High," "Medium,"
"Low," "Off." The light on hanger assembly.
1. Blade brackets loosely screwed to blade bracket. 3. Blade screwed loosely to motor. 2. Loose blades or blade brackets. 5. Turn...
Parts Guide - Page 1
...23710 92582-01 Burnished Brass
Part #
1
84102-01
1
92581-01
1
84095-01
1
74228-03
1
74017-09
1
74002-75
9
63755-05
1
83905/3
3
64555-01
12
03435-03
1
92582-00-860
4
07649-01
4
77646-04
1
07570-01
Hunter Fan...
Screw, Blade Assembly
Blade Grommet
Screw, Switch Housing Assembly
Thumbscrew
Hanger Bracket Assembly
Blade Assembly
Switch Housing Assembly
Fan Parts
(Not ...
Similar Questions
Replacement Motor
hi,do you have a replacement motor for this fan.I believe it is a Whisperwind 2.85 amps?Thank
hi,do you have a replacement motor for this fan.I believe it is a Whisperwind 2.85 amps?Thank
(Posted by Stevecourtier 3 years ago)
Hi,how Much For A New Motor And Capacitor For The Hunter Medalist Type 2 Model
model 23710. 000019 cat no. 23710-10
model 23710. 000019 cat no. 23710-10
(Posted by Stevecourtier 3 years ago)
Need For Replacement Switch Housing Assembly In Hunter Ceiling Fan.
Fan model 20728, housing part Purchased 12/2009
Fan model 20728, housing part Purchased 12/2009
(Posted by Anonymous-161179 7 years ago)
I Need A Replacement Switch Housing Assembly For Hunter 28680.
My parts list says it is item #: 98378-01. I purchase 5 fans and the lights won't light on one unit....
My parts list says it is item #: 98378-01. I purchase 5 fans and the lights won't light on one unit....
(Posted by johnsid79726 9 years ago)
I Need A Gear Box For A Hunter Floor Fan Model # 90122a
This is a reciprocating gear box. The mounting casting (pot metal) is broken.
This is a reciprocating gear box. The mounting casting (pot metal) is broken.
(Posted by davecallahan 11 years ago)