Humax IR-ACE Support Question
Humax IR-ACE Support Question
Find answers below for this question about Humax IR-ACE.Need a Humax IR-ACE manual? We have 1 online manual for this item!
Current Answers
Related Humax IR-ACE Manual Pages
User Manual - Page 3
...or disconnecting the cable from the wall outlet before connecting or disconnecting the cable from the satellite dish. VENTILATION
: The slots on top of the STB must comply with SABS 061... to dripping or splashing, and no solvents) to satisfy international safety standards. CONNECTION TO THE SATELLITE DISH LNB : Disconnect the STB from the mains before cleaning. EARTHING
: The LNB cable ...
User Manual - Page 4
.... • Polarisation Characteristic of an electromagnetic wave determined by the use of Telenor Conax AS. This includes a satellite dish and a broadband antenna. • Forward Error Correction (FEC) An error control system for any problems caused... IF range. • Packet Identifier (PID) A set of numbers that receives, amplifies and retransmits a signal on a different frequency. GB3
User Manual - Page 5
Do the same for example analogue) to the common antenna equipment receiver that has satellite signals.
4. DiSEqC 1.2 Connection Please refer to the STB simultaneously. Connecting a Satellite antenna You can connect a further Sat-receiver (for the other end to the RF DiSEqC switch output connector and the
other LNBs. 4. Connect the coaxial cable from the second...
User Manual - Page 6
...manufacturer reserves the right to the model
requiring upgrading); (c) OTA over the air via satellite systems. Note that users register with this software upgrade takes place by the
manufacturer. ...software versions may be properly "tuned" to release via a designated satellite
system; 3) the equipment must be received). It is recommended that OTA is an official trademark and logo ...
User Manual - Page 8
... switch between Operation and Standby modes.
RADIO LED (YELLOW) The LED light goes on when in RADIO mode. TV/RADIO Press to volume down .
V+ (Model IR-ACE M only) Use to change services up .
GB7
STANDBY LED (RED) Indicates that the STB is under standby. SLOT For a CA Module with a smart card.
PUse...
User Manual - Page 9
STB Connections
Rear Panel
IR-ACE IR-ACE M
GB8
User Manual - Page 11
...RF OUT on STB and the other end to a terrestrial antenna connection or the socket for model IR-ACE.
TV with RCA / Cinch) 1. For best results, we recommend using one end of RCA/...TV doesn't have a RCA/Cinch socket, connect one end of the following set-ups:
Note: STB model IR-ACE shown; GB10 STB Connections
There are the same for public antenna on the wall. 4. With a Hi-...
User Manual - Page 12
... STB.
Connect one end of your motorised system(DiSEqC 1.2 Motor)
to a RCA/Cinch socket on your VCR. 3. TV with Motorised System (DiSEqC 1.2) 1. Note: STB model IR-ACE shown; Connect the coaxial cable from the LNB of a RCA/Cinch cable to the RCA/Cinch connector on the STB
and the other end to...
User Manual - Page 32
... button. 4. Box display, proceed as follows: 1. Select the desired menu mode using the button. 4. OSD Transparency To set the duration time of services belonging to a satellite. Activate the Other Setting menu via the Main menu. 2. Select the OSD Transparency item using the button. 3. Select the Info. Press the OK ( ) or EXIT...
User Manual - Page 41
..., press the OK ( )
button to delete all the marked satellite names. 6. To delete a satellite, proceed as follows: 1. Activate the Delete Satellite menu via the Main menu. 2.
Main Menu Guide
Delete Satellites The Delete Satellites menu supplies the following functions: • Delete a satellite. Activate the Delete Satellite menu via the Main menu. 2. If all services belonging to...
User Manual - Page 42
... antenna. The Antenna Setting menu supplies the following items to the long length of each antenna. Hence, the value is unique for SMATV. Moreover, the satellite name can be set on "High".
3-3.
LNB Power Switches/off the LNB power. Motorised System Disables/enables the motorise function. To compensate the voltage drop...
User Manual - Page 43
... option is enabled, the scrambled services are skipped during the search.
BAT Search Some operators define the order of services in a list using information from a satellite transponder. (If the Network Search option is enabled, the services will be searched according to the BAT information. If this option is enabled, all services...
User Manual - Page 45
... is to four symbol rates for searching when the search type is "Detail". Symbol Rate table(optional) Upsets up to search services using information from a satellite. To automatically search the services, proceed as parameters. Activate the Automatic Search menu. 2. Since the Automatic Search is based on the parameter settings. To obtain...
User Manual - Page 46
... the Main menu. 2. 3-4. Activate the Status Menu via the STB Upgrade menu. To receive the information, proceed as the signal level and quality are maximally high when the antenna is...Signal Detection menu using the button,
then press the OK ( ) button to exit the menu. To receive the information, proceed as : • Information on the Software version, • Information on the Hardware...
User Manual - Page 48
...has not yet been viewed, a 'U' is marked in the "TYPE" column means that the received mail message is a message of the screen. Utility
The Utility menu supplies two functions: Calendar ... supplies information on the screen. Mail Messages
The Mail Messages menu shows the mail messages received over the air.
Select the desired mail message using the
button. Press the GREEN button...
User Manual - Page 49
... to use the
buttons. 8. You must set up so that can use the available DiSEqC 1.2 functions. This menu is called "Satellite Setting" and is not available, please use another one. Setting your receiver up a separate alternative antenna for better reception. To return to the Main Menu, use the EXIT ( ) button until you...
User Manual - Page 50
... Search
This is required when you are located.
(Please consult the user's manual for your motor is set your receiver is installed correctly with the calibrations
adjusted for the region in the Satellite Settings menu.
4. You should now see the Service
Searching menu.
4. Highlight the Alternative Antenna option and press the OK...
User Manual - Page 51
...and Strength Quality bar at the position you want.
10. To do this satellite.
3. Highlight the Satellite name option and use as your
motor East or West until it east so ... this to the Motor Control option, and using the
buttons, change this position, it is the satellite's position. You should register a signal once. Highlight the DiSEqC Command Mode option and, using the...
User Manual - Page 53
..., press the OK ( ) button to Automatic Search on page GB42. 5. When you 3set for the satellite you want , you have to wait a few seconds to allow the motor to move into position to use your receiver as normal. GB52 Now that you can use automatic search using the DiSEqC 1.2 motorised system. 1. Automatic...
User Manual - Page 58
... analogue TV programme. The input should be protected against
lightning
Physical Specifications
Size (W x H x D)
Weight (Net) Operating Temp Storage Temp Storage Humidity
260 x 50 x 182 mm (IR-ACE) 310 x 60 x 225 mm (IR-ACE M) Around 3.0 kg 0°C to + 45°C -10°C to EUTELSAT.
Similar Questions
Need To Do Sw Update For Humax Satellite Receiver Ir-hd1000
My Receiver is Humax IR-HD1000SW ver. MHZZSIR 1.00.05 (this is the working SW).I need to update to t...
My Receiver is Humax IR-HD1000SW ver. MHZZSIR 1.00.05 (this is the working SW).I need to update to t...
(Posted by YasirAbuelhassan 4 years ago)
Sw Update For Satellite Receiver Humax Ir Ace Ii
Looking for the assistance how to do manually the soft ware update for my receiver HUMAX IR-ACE II.W...
Looking for the assistance how to do manually the soft ware update for my receiver HUMAX IR-ACE II.W...
(Posted by rlotfi 9 years ago)
Update The Software Of Humax Receiver Ir-dh1000 Manually
WHAT IS THE FREQUANCY TO UPDATE THE SOFTWARE OF HUMAX RECEIVER IR-DH1000 MANUALLY?
WHAT IS THE FREQUANCY TO UPDATE THE SOFTWARE OF HUMAX RECEIVER IR-DH1000 MANUALLY?
(Posted by akhdair 12 years ago)
Which Remote Control Unit Goes With Humax Ir- Ace
WHICH REMOTE CONTROL UNIT GOES WITH HUMAX IR- ACE
WHICH REMOTE CONTROL UNIT GOES WITH HUMAX IR- ACE
(Posted by cazzatyler 12 years ago)