Hoover UH70040W Support Question
Hoover UH70040W Support Question
Find answers below for this question about Hoover UH70040W.Need a Hoover UH70040W manual? We have 1 online manual for this item!
Question posted by teknocfre on February 24th, 2014
How To Change The Belts On A Mach Cyclonic Vacuum Uh70040w
The person who posted this question about this Hoover product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hoover UH70040W Manual Pages
Product Manual - Page 1
Lire attentivement ces instructions avant d'utiliser l'appareil. ®
Cyclonic Upright
®
Vacuum Cleaner
Aspirateur vertical
cyclonique
Owner's Manual
ENGLISH § pp. 1-...Cup 8-9 Replacing Agitator Brush Roll ..11-12 Replacing Belt 10-11 Replacing Powered Hand Tool
Agitator Brush Roll 12 Replacing Power Hand Tool Belt ..13 Replacing Headlight 10 Thermal Protector 14 Warranty 15 ...
Product Manual - Page 2
...electric shock, or injury:
• Do not use outdoors or on cord. Do not allow vacuum cleaner to the State of body away from electrical outlet before unplugging. • Do not unplug ... left outdoors, or
dropped into openings. Keep cord away from heated surfaces. • Use vacuum cleaner only for choosing a HOOVER® product
Please enter the COMPLETE model and serial numbers ...
Product Manual - Page 5
...-off pedal 19 12. Nozzle control knob: turn cleaner OFF, push switch again.
2-3
B
A
The cleaner is wider than the other). Combination tool 25. Do not change the plug in the OFF position. The indicator (B) will fit in the "brush roll on the pedal (A). Headlight 10. Hose/tool holder 18. Cord reel...
Product Manual - Page 9
Cleaning filters
Cyclonic filter assembly 3-7
How to clean
Disconnect cleaner from the filter assembly by inserting tabs (B) into cleaner body. Place the filter assembly on dirt cup (B) and
...
Product Manual - Page 10
...Disconnect cleaner from the filter cartridge by brushing with the cleaner's combination tool.
Replace belt if it over.
Push new bulb straight into position on cleaner. Excessive force is ...under "Agitator brush roll".
What to buy
To assure effective operation, use only genuine HOOVER belts with the screw. HOOVER part No. 40201-271.
10 Press handle release pedal and ...
Product Manual - Page 11
...screws securely.
Turn cleaner over .
3-13
3-14
B
3-15
D
C
A
Replacing flat belt
Disconnect cleaner from electrical outlet.
Place handle in direction shown.
What to lowest setting.
Continued
11...worn, the agitator brush roll should be replaced. Lift up . Removing belt
Remove used belt (B) from electrical outlet.
Unplug cleaner before turning it over so bottom ...
Product Manual - Page 12
... is in groove (D) on agitator brush roll. Belt will "pop" into place.
Insert agitator brush roll through belt and position belt in good condition. Reposition flat belt and bottom plate (Figs. 3-15 through belt and position belt over gear teeth (D) on side of cleaner.
Inspect belt to pulley. If belt is cracked, gouged or broken, replace it into...
Product Manual - Page 13
... slide retainers into grooves (D) in tool housing and snap into place. 5.
The belt can be replaced.
3-30
Replace belt
When replacing belt, ask for HOOVER part No. 38528-037.
3-31 B
A
1. With flat...
7. 3-27
3-28
B
3-29
A
C
E
6. Remove tool from turbine pulley (B).
Replace belt guard (B) making sure not to remove.
3.
With curved ends down, slide end plates (C) of the nozzle...
Product Manual - Page 14
... is found by using tool applying light
pressure. • Blockage in turbine channel • Remove blockage. • Broken or worn belt • Replace belt • Low cleaner suction • Check items under "Vacuum Cleaners Household" OR • checking the list of Sales and Service Centers provided with two ball bearings that contain sufficient...
Product Manual - Page 15
... plate (Fig. 3-13) and agitator brush roll (Fig. 3-20). Remove bottom plate, belt guard and turbine as described in and turn ON. This warranty only applies when the product is... roll and bottom plate.
If a blockage occurs during the warranted period. Replace belt turbine, brush roll, belt guard and bottom plate.
This warranty applies when the appliance is purchased. Military...
Similar Questions
How To Change Belt For Power Nozzle?
How to change belt for power nozzle?
How to change belt for power nozzle?
(Posted by Missionnews777 1 year ago)
How Come My A Uh70040 W Vacuu M Wont Suck But If You Use The Hose By Its Elf
(Posted by thethreeofus 9 years ago)
I Have The Hoover Uh70040w Mach Cyclonic Upright Vacuum Cleaner Its Sliver And I
I have the hoover cyclonic upright vaccume cleaner it is making a very lound grinding like noise whe...
I have the hoover cyclonic upright vaccume cleaner it is making a very lound grinding like noise whe...
(Posted by dorkylilrawr 9 years ago)
Belt Part
Is part number 40201-200 the belt I need to turn the brush
Is part number 40201-200 the belt I need to turn the brush
(Posted by looper922 10 years ago)